[OpenWrt-Devel] [PATCH] ath79: add support for GL.iNet GL-X1200

guilin.wang at gl-inet.com guilin.wang at gl-inet.com
Thu Apr 9 23:53:54 EDT 2020


This patch adds supports for GL-X1200.

Specification:
	- SOC: QCA9563 (775MHz)
	- Flash: 16 MiB
	- RAM: 128 MiB DDR2
	- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
	- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
	- SIM: 2x SIM card slots
	- MicroSD: 1x microSD slot
	- Antenna: 2x external 5dBi antennas
	- USB: 1x USB 2.0 port
	- Button: 1x reset button
	- LED: 16x LEDs (3x GPIO controllable)
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
	- OEM U-Boot supplies HTTP/GUI access

Implementation Notes
====================

Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.

The mode LEDs are
    * Boot, Running   system
    * Failsafe        2G
    * Upgrade         5G

Installation
============

Using sysupgrade
----------------

sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished

using U-Boot.

To glinet_gl-x1200-nand:

    gl-x1200          OEM NAND, Self-built from OEM source NAND

To glinet_gl-x1200-nor:

    gl-x1200          Self-built from OEM source NOR
    glinet_gl-ar750s   OpenWrt NOR (prior builds)

Using U-Boot
------------

The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second.  When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:

    curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
         http://192.168.1.1/index.html
or
    curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
         http://192.168.1.1/index.html

Note that NOR vs. NAND is based on the file name extension.

Signed-off-by: guilin.wang at gl-inet.com <guilin.wang at gl-inet.com>
---
 .../ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts |  18 ++
 .../ath79/dts/qca9563_glinet_gl-x1200-nor.dts      |  18 ++
 .../linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi   | 199 +++++++++++++++++++++
 target/linux/ath79/image/nand.mk                   |  34 ++++
 .../ath79/nand/base-files/etc/board.d/02_network   |   5 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata       |  10 ++
 .../ath79/nand/base-files/lib/upgrade/platform.sh  |   4 +-
 7 files changed, 287 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
 create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
 create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi

diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
new file mode 100644
index 0000000..1fefd4f
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_glinet_gl-x1200.dtsi"
+
+/ {
+	compatible = "glinet,gl-x1200-nor-nand", "qca,qca9563";
+	model = "GL.iNet GL-X1200 (NOR/NAND)";
+};
+
+&nor_kernel {
+	label = "kernel";
+};
+
+&nand_ubi {
+	label = "ubi";
+};
diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
new file mode 100644
index 0000000..4eded21
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_glinet_gl-x1200.dtsi"
+
+/ {
+	compatible = "glinet,gl-x1200-nor", "qca,qca9563";
+	model = "GL.iNet GL-X1200 (NOR)";
+};
+
+/delete-node/ &nor_kernel;
+/delete-node/ &nor_reserved;
+
+&nor_firmware {
+	compatible = "denx,uimage";
+	label = "firmware";
+};
diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
new file mode 100644
index 0000000..60e3dba
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	compatible = "glinet,gl-x1200", "qca,qca9563";
+	model = "GL.iNet GL-X1200";
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+		label-mac-device = &eth0;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&jtag_disable_pins>;
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_system: system {
+			label = "gl-x1200:red:system";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		led_wlan2g: wlan2g {
+			label = "gl-x1200:green:wlan2g";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		led_wlan5g: wlan5g {
+			label = "gl-x1200:green:wlan5g";
+			gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+	gpio-export {
+		compatible = "gpio-export";
+
+		gpio_modem1_power {
+			gpio-export,name = "gl-x1200:4g1:power";
+			gpio-export,output = <1>;
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		gpio_usb_power {
+			gpio-export,name = "gl-x1200:usb:power";
+			gpio-export,output = <1>;
+			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		gpio_modem2_power {
+			gpio-export,name = "gl-x1200:4g2:power";
+			gpio-export,output = <1>;
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <2>;
+
+	flash_nor: flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		nor_partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition at 40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			art: partition at 50000 {
+				label = "art";
+				reg = <0x050000 0x010000>;
+				read-only;
+			};
+
+			nor_firmware: partition at 60000 {
+				label = "nor_firmware";
+				reg = <0x060000 0xfa0000>;
+			};
+
+			nor_kernel: partition_alt at 60000 {
+				label = "nor_kernel";
+				reg = <0x060000 0x400000>;
+			};
+
+			nor_reserved: parition_alt at 460000 {
+				label = "nor_reserved";
+				reg = <0x460000 0xba0000>;
+			};
+		};
+	};
+
+	flash_nand: flash at 1 {
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <25000000>;
+
+		nand_partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			nand_ubi: partition at 0 {
+				label = "nand_ubi";
+				reg = <0x000000 0x8000000>;
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&phy0>;
+	mtd-mac-address = <&art 0x0>;
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy-mask = <0>;
+
+	phy0: ethernet-phy at 0 {
+		reg = <0>;
+		phy-mode = "sgmii";
+		qca,ar8327-initvals = <
+			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+			0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk
index 3ccd199..712e90d 100644
--- a/target/linux/ath79/image/nand.mk
+++ b/target/linux/ath79/image/nand.mk
@@ -130,6 +130,40 @@ define Device/glinet_gl-ar750s-nor
 endef
 TARGET_DEVICES += glinet_gl-ar750s-nor
 
+define Device/glinet_gl-x1200-common
+  SOC := qca9563
+  DEVICE_VENDOR := GL.iNet
+  DEVICE_MODEL := GL-X1200
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct kmod-usb2 kmod-leds-gpio\
+	kmod-usb-storage block-mount kmod-usb-net-qmi-wwan
+  KERNEL_SIZE := 2048k
+  IMAGE_SIZE := 16000k
+  PAGESIZE := 2048
+  VID_HDR_OFFSET := 2048
+endef
+
+# NB: The kernel size is intentionally restricted at this time; see commit message
+define Device/glinet_gl-x1200-nor-nand
+  $(Device/glinet_gl-x1200-common)
+  DEVICE_VARIANT := NOR/NAND
+  BLOCKSIZE := 128k
+  GL_UBOOT_UBI_OFFSET := 2048k
+  IMAGES += factory.img
+  IMAGE/factory.img := append-kernel | pad-to $$$$(GL_UBOOT_UBI_OFFSET) | \
+	append-ubi | check-kernel-size $$$$(GL_UBOOT_UBI_OFFSET)
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  SUPPORTED_DEVICES += glinet,gl-x1200-nor
+endef
+TARGET_DEVICES += glinet_gl-x1200-nor-nand
+
+define Device/glinet_gl-x1200-nor
+  $(Device/glinet_gl-x1200-common)
+  DEVICE_VARIANT := NOR
+  BLOCKSIZE := 64k
+  SUPPORTED_DEVICES += gl-x1200 glinet,gl-x1200 glinet,gl-x1200-nor-nand
+endef
+TARGET_DEVICES += glinet_gl-x1200-nor
+
 # fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + 0xff)
 define Device/netgear_ath79_nand
   DEVICE_VENDOR := NETGEAR
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network
index b2191ee..cd1e0a7 100755
--- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
@@ -20,6 +20,11 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0 at eth0" "2:lan:2" "3:lan:1" "1:wan"
 		;;
+	glinet,gl-x1200-nor|\
+	glinet,gl-x1200-nor-nand)
+		ucidef_add_switch "switch0" \
+			"0 at eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
+		;;
 	netgear,wndr3700-v4|\
 	netgear,wndr4300|\
 	netgear,wndr4300-v2|\
diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index d5fd3db..02f226c 100644
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -24,6 +24,16 @@ case "$FIRMWARE" in
 		;;
 	esac
 	;;
+"ath10k/pre-cal-pci-0000:00:00.0.bin")
+	case $board in
+	glinet,gl-x1200-nor|\
+	glinet,gl-x1200-nor-nand)
+		caldata_extract "art" 0x5000 0x2f20
+		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+		;;
+	esac
+	;;
 *)
 	exit 1
 	;;
diff --git a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
index ea77345..4ea2287 100644
--- a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
@@ -19,7 +19,9 @@ platform_do_upgrade() {
 		glinet_nand_nor_do_upgrade "$1"
 		;;
 	glinet,gl-ar750s-nor|\
-	glinet,gl-ar750s-nor-nand)
+	glinet,gl-ar750s-nor-nand |\
+	glinet,gl-x1200-nor|\
+	glinet,gl-x1200-nor-nand)
 		nand_nor_do_upgrade "$1"
 		;;
 	*)
-- 
2.7.4




_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list