[OpenWrt-Devel] [PATCH] ath79: add support for GL.iNet GL-X1200
guilin.wang at gl-inet.com
guilin.wang at gl-inet.com
Fri Apr 10 00:50:13 EDT 2020
This patch adds supports for GL-X1200.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB
- RAM: 128 MiB DDR2
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
- SIM: 2x SIM card slots
- MicroSD: 1x microSD slot
- Antenna: 2x external 5dBi antennas
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 16x LEDs (3x GPIO controllable)
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
- OEM U-Boot supplies HTTP/GUI access
Implementation Notes
====================
Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.
The mode LEDs are
* Boot, Running system
* Failsafe 2G
* Upgrade 5G
Installation
============
Using sysupgrade
----------------
sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished
using U-Boot.
To glinet_gl-x1200-nand:
gl-x1200 OEM NAND, Self-built from OEM source NAND
To glinet_gl-x1200-nor:
gl-x1200 Self-built from OEM source NOR
glinet_gl-x1200 OpenWrt NOR (prior builds)
Using U-Boot
------------
The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second. When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:
curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
http://192.168.1.1/index.html
or
curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
http://192.168.1.1/index.html
Note that NOR vs. NAND is based on the file name extension.
Signed-off-by: guilin.wang at gl-inet.com <guilin.wang at gl-inet.com>
---
.../ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts | 18 ++
.../ath79/dts/qca9563_glinet_gl-x1200-nor.dts | 18 ++
.../linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi | 199 +++++++++++++++++++++
target/linux/ath79/image/nand.mk | 34 ++++
.../ath79/nand/base-files/etc/board.d/02_network | 5 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 10 ++
.../ath79/nand/base-files/lib/upgrade/platform.sh | 4 +-
7 files changed, 287 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
new file mode 100644
index 0000000..1fefd4f
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_glinet_gl-x1200.dtsi"
+
+/ {
+ compatible = "glinet,gl-x1200-nor-nand", "qca,qca9563";
+ model = "GL.iNet GL-X1200 (NOR/NAND)";
+};
+
+&nor_kernel {
+ label = "kernel";
+};
+
+&nand_ubi {
+ label = "ubi";
+};
diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
new file mode 100644
index 0000000..4eded21
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_glinet_gl-x1200.dtsi"
+
+/ {
+ compatible = "glinet,gl-x1200-nor", "qca,qca9563";
+ model = "GL.iNet GL-X1200 (NOR)";
+};
+
+/delete-node/ &nor_kernel;
+/delete-node/ &nor_reserved;
+
+&nor_firmware {
+ compatible = "denx,uimage";
+ label = "firmware";
+};
diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
new file mode 100644
index 0000000..60e3dba
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+ compatible = "glinet,gl-x1200", "qca,qca9563";
+ model = "GL.iNet GL-X1200";
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ aliases {
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ label-mac-device = ð0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system: system {
+ label = "gl-x1200:red:system";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ led_wlan2g: wlan2g {
+ label = "gl-x1200:green:wlan2g";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led_wlan5g: wlan5g {
+ label = "gl-x1200:green:wlan5g";
+ gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+ gpio-export {
+ compatible = "gpio-export";
+
+ gpio_modem1_power {
+ gpio-export,name = "gl-x1200:4g1:power";
+ gpio-export,output = <1>;
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ gpio_usb_power {
+ gpio-export,name = "gl-x1200:usb:power";
+ gpio-export,output = <1>;
+ gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_modem2_power {
+ gpio-export,name = "gl-x1200:4g2:power";
+ gpio-export,output = <1>;
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <2>;
+
+ flash_nor: flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ nor_partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ art: partition at 50000 {
+ label = "art";
+ reg = <0x050000 0x010000>;
+ read-only;
+ };
+
+ nor_firmware: partition at 60000 {
+ label = "nor_firmware";
+ reg = <0x060000 0xfa0000>;
+ };
+
+ nor_kernel: partition_alt at 60000 {
+ label = "nor_kernel";
+ reg = <0x060000 0x400000>;
+ };
+
+ nor_reserved: parition_alt at 460000 {
+ label = "nor_reserved";
+ reg = <0x460000 0xba0000>;
+ };
+ };
+ };
+
+ flash_nand: flash at 1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <25000000>;
+
+ nand_partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nand_ubi: partition at 0 {
+ label = "nand_ubi";
+ reg = <0x000000 0x8000000>;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&phy0>;
+ mtd-mac-address = <&art 0x0>;
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0>;
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ qca,ar8327-initvals = <
+ 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ >;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb_phy1 {
+ status = "okay";
+};
+
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk
index 3ccd199..712e90d 100644
--- a/target/linux/ath79/image/nand.mk
+++ b/target/linux/ath79/image/nand.mk
@@ -130,6 +130,40 @@ define Device/glinet_gl-ar750s-nor
endef
TARGET_DEVICES += glinet_gl-ar750s-nor
+define Device/glinet_gl-x1200-common
+ SOC := qca9563
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-X1200
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct kmod-usb2 kmod-leds-gpio\
+ kmod-usb-storage block-mount kmod-usb-net-qmi-wwan
+ KERNEL_SIZE := 2048k
+ IMAGE_SIZE := 16000k
+ PAGESIZE := 2048
+ VID_HDR_OFFSET := 2048
+endef
+
+# NB: The kernel size is intentionally restricted at this time; see commit message
+define Device/glinet_gl-x1200-nor-nand
+ $(Device/glinet_gl-x1200-common)
+ DEVICE_VARIANT := NOR/NAND
+ BLOCKSIZE := 128k
+ GL_UBOOT_UBI_OFFSET := 2048k
+ IMAGES += factory.img
+ IMAGE/factory.img := append-kernel | pad-to $$$$(GL_UBOOT_UBI_OFFSET) | \
+ append-ubi | check-kernel-size $$$$(GL_UBOOT_UBI_OFFSET)
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ SUPPORTED_DEVICES += glinet,gl-x1200-nor
+endef
+TARGET_DEVICES += glinet_gl-x1200-nor-nand
+
+define Device/glinet_gl-x1200-nor
+ $(Device/glinet_gl-x1200-common)
+ DEVICE_VARIANT := NOR
+ BLOCKSIZE := 64k
+ SUPPORTED_DEVICES += gl-x1200 glinet,gl-x1200 glinet,gl-x1200-nor-nand
+endef
+TARGET_DEVICES += glinet_gl-x1200-nor
+
# fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + 0xff)
define Device/netgear_ath79_nand
DEVICE_VENDOR := NETGEAR
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network
index b2191ee..cd1e0a7 100755
--- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
@@ -20,6 +20,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "2:lan:2" "3:lan:1" "1:wan"
;;
+ glinet,gl-x1200-nor|\
+ glinet,gl-x1200-nor-nand)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
+ ;;
netgear,wndr3700-v4|\
netgear,wndr4300|\
netgear,wndr4300-v2|\
diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index d5fd3db..02f226c 100644
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -24,6 +24,16 @@ case "$FIRMWARE" in
;;
esac
;;
+"ath10k/pre-cal-pci-0000:00:00.0.bin")
+ case $board in
+ glinet,gl-x1200-nor|\
+ glinet,gl-x1200-nor-nand)
+ caldata_extract "art" 0x5000 0x2f20
+ ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+ ;;
+ esac
+ ;;
*)
exit 1
;;
diff --git a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
index ea77345..4ea2287 100644
--- a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
@@ -19,7 +19,9 @@ platform_do_upgrade() {
glinet_nand_nor_do_upgrade "$1"
;;
glinet,gl-ar750s-nor|\
- glinet,gl-ar750s-nor-nand)
+ glinet,gl-ar750s-nor-nand |\
+ glinet,gl-x1200-nor|\
+ glinet,gl-x1200-nor-nand)
nand_nor_do_upgrade "$1"
;;
*)
--
2.7.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list