[OpenWrt-Devel] [PATCH] ar71xx: add support for GL.iNet GL-X1200
mail at adrianschmutzler.de
mail at adrianschmutzler.de
Sat Apr 11 18:01:08 EDT 2020
Hi,
> -----Original Message-----
> From: openwrt-devel [mailto:openwrt-devel-bounces at lists.openwrt.org]
> On Behalf Of guilin.wang at gl-inet.com
> Sent: Freitag, 10. April 2020 05:44
> To: openwrt-devel at lists.openwrt.org
> Cc: guilin.wang at gl-inet.com
> Subject: [OpenWrt-Devel] [PATCH] ar71xx: add support for GL.iNet GL-X1200
The ar71xx target has been deprecated for a long time and will not be included in the next release branch.
Consequently, we do not accept any new devices there, but will focus on the ath79 patch supplied in parallel.
Best
Adrian
>
> This patch adds supports for GL-X1200.
>
> Specification:
> - SOC: QCA9563 (775MHz)
> - Flash: 16 MiB
> - RAM: 128 MiB DDR2
> - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
> - Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
> - SIM: 2x SIM card slots
> - MicroSD: 1x microSD slot
> - Antenna: 2x external 5dBi antennas
> - USB: 1x USB 2.0 port
> - Button: 1x reset button
> - LED: 16x LEDs (3x GPIO controllable)
> - UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
> - OEM U-Boot supplies HTTP/GUI access
>
> Implementation Notes
> ====================
>
> Both the NOR and NAND variants boot off a NOR-based kernel, consistent
> with the OEM's firmware.
>
> The mode LEDs are
> * Boot, Running system
> * Failsafe 2G
> * Upgrade 5G
>
> Installation
> ============
>
> Using sysupgrade
> ----------------
>
> sysupgrade may be used to install a NAND image on a device running a NAND
> image or a NOR image on a device running a NOR image. It is recommended
> to *not* preserve config when upgrading from OEM firmware or previous
> versions of OpenWrt. No supported sysupgrade path should require "force".
> Transitioning from NOR to NAND can be accomplished
>
> using U-Boot.
>
> To glinet_gl-x1200-nand:
>
> gl-x1200 OEM NAND, Self-built from OEM source NAND
>
> To glinet_gl-x1200-nor:
>
> gl-x1200 Self-built from OEM source NOR
> glinet_gl-ar750s OpenWrt NOR (prior builds)
>
> Using U-Boot
> ------------
>
> The OEM U-Boot can be put into a graphical, firmware-upload mode by
> holding down the button on the side of the router while applying power and
> for a bit more than five seconds following with the current OEM U-Boot. The
> power LED will come on, then the 5G LED will flash five times, about once a
> second. When the 5G LED stops flashing and the 2G LED lights solid, the
> router's U-Boot will provide an upload page at http://192.168.1.1/ Either a
> browser may be used to upload an image, or a utility such as curl may be
> used:
>
> curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
> http://192.168.1.1/index.html
> or
> curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
> http://192.168.1.1/index.html
>
> Note that NOR vs. NAND is based on the file name extension.
>
> Signed-off-by: guilin.wang at gl-inet.com <guilin.wang at gl-inet.com>
> ---
> .../ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts | 18 ++
> .../ath79/dts/qca9563_glinet_gl-x1200-nor.dts | 18 ++
> .../linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi | 199
> +++++++++++++++++++++
> target/linux/ath79/image/nand.mk | 34 ++++
> .../ath79/nand/base-files/etc/board.d/02_network | 5 +
> .../etc/hotplug.d/firmware/11-ath10k-caldata | 10 ++
> .../ath79/nand/base-files/lib/upgrade/platform.sh | 4 +-
> 7 files changed, 287 insertions(+), 1 deletion(-) create mode 100644
> target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
> create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
> create mode 100644 target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
>
> diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
> b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
> new file mode 100644
> index 0000000..1fefd4f
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts
> @@ -0,0 +1,18 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +/dts-v1/;
> +
> +#include "qca9563_glinet_gl-x1200.dtsi"
> +
> +/ {
> + compatible = "glinet,gl-x1200-nor-nand", "qca,qca9563";
> + model = "GL.iNet GL-X1200 (NOR/NAND)"; };
> +
> +&nor_kernel {
> + label = "kernel";
> +};
> +
> +&nand_ubi {
> + label = "ubi";
> +};
> diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
> b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
> new file mode 100644
> index 0000000..4eded21
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts
> @@ -0,0 +1,18 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +/dts-v1/;
> +
> +#include "qca9563_glinet_gl-x1200.dtsi"
> +
> +/ {
> + compatible = "glinet,gl-x1200-nor", "qca,qca9563";
> + model = "GL.iNet GL-X1200 (NOR)";
> +};
> +
> +/delete-node/ &nor_kernel;
> +/delete-node/ &nor_reserved;
> +
> +&nor_firmware {
> + compatible = "denx,uimage";
> + label = "firmware";
> +};
> diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
> b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
> new file mode 100644
> index 0000000..60e3dba
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi
> @@ -0,0 +1,199 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "qca956x.dtsi"
> +
> +/ {
> + compatible = "glinet,gl-x1200", "qca,qca9563";
> + model = "GL.iNet GL-X1200";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + aliases {
> + led-boot = &led_system;
> + led-failsafe = &led_system;
> + led-running = &led_system;
> + led-upgrade = &led_system;
> + label-mac-device = ð0;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&jtag_disable_pins>;
> +
> + reset {
> + label = "reset";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_system: system {
> + label = "gl-x1200:red:system";
> + gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> + default-state = "keep";
> + };
> +
> + led_wlan2g: wlan2g {
> + label = "gl-x1200:green:wlan2g";
> + gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy1tpt";
> + };
> +
> + led_wlan5g: wlan5g {
> + label = "gl-x1200:green:wlan5g";
> + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tpt";
> + };
> + };
> + gpio-export {
> + compatible = "gpio-export";
> +
> + gpio_modem1_power {
> + gpio-export,name = "gl-x1200:4g1:power";
> + gpio-export,output = <1>;
> + gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
> + };
> +
> + gpio_usb_power {
> + gpio-export,name = "gl-x1200:usb:power";
> + gpio-export,output = <1>;
> + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
> + };
> +
> + gpio_modem2_power {
> + gpio-export,name = "gl-x1200:4g2:power";
> + gpio-export,output = <1>;
> + gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&spi {
> + status = "okay";
> +
> + num-cs = <2>;
> +
> + flash_nor: flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> +
> + nor_partitions: partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x000000 0x040000>;
> + read-only;
> + };
> +
> + partition at 40000 {
> + label = "u-boot-env";
> + reg = <0x040000 0x010000>;
> + };
> +
> + art: partition at 50000 {
> + label = "art";
> + reg = <0x050000 0x010000>;
> + read-only;
> + };
> +
> + nor_firmware: partition at 60000 {
> + label = "nor_firmware";
> + reg = <0x060000 0xfa0000>;
> + };
> +
> + nor_kernel: partition_alt at 60000 {
> + label = "nor_kernel";
> + reg = <0x060000 0x400000>;
> + };
> +
> + nor_reserved: parition_alt at 460000 {
> + label = "nor_reserved";
> + reg = <0x460000 0xba0000>;
> + };
> + };
> + };
> +
> + flash_nand: flash at 1 {
> + compatible = "spi-nand";
> + reg = <1>;
> + spi-max-frequency = <25000000>;
> +
> + nand_partitions: partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + nand_ubi: partition at 0 {
> + label = "nand_ubi";
> + reg = <0x000000 0x8000000>;
> + };
> + };
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + phy-handle = <&phy0>;
> + mtd-mac-address = <&art 0x0>;
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + phy-mask = <0>;
> +
> + phy0: ethernet-phy at 0 {
> + reg = <0>;
> + phy-mode = "sgmii";
> + qca,ar8327-initvals = <
> + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
> + 0x7c 0x0000007e /* PORT0_STATUS */
> + >;
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&uart {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> +
> +&usb_phy0 {
> + status = "okay";
> +};
> +
> +&usb_phy1 {
> + status = "okay";
> +};
> +
> +
> +&wmac {
> + status = "okay";
> +
> + mtd-cal-data = <&art 0x1000>;
> +};
> diff --git a/target/linux/ath79/image/nand.mk
> b/target/linux/ath79/image/nand.mk
> index 3ccd199..712e90d 100644
> --- a/target/linux/ath79/image/nand.mk
> +++ b/target/linux/ath79/image/nand.mk
> @@ -130,6 +130,40 @@ define Device/glinet_gl-ar750s-nor endef
> TARGET_DEVICES += glinet_gl-ar750s-nor
>
> +define Device/glinet_gl-x1200-common
> + SOC := qca9563
> + DEVICE_VENDOR := GL.iNet
> + DEVICE_MODEL := GL-X1200
> + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct kmod-
> usb2 kmod-leds-gpio\
> + kmod-usb-storage block-mount kmod-usb-net-qmi-wwan
> + KERNEL_SIZE := 2048k
> + IMAGE_SIZE := 16000k
> + PAGESIZE := 2048
> + VID_HDR_OFFSET := 2048
> +endef
> +
> +# NB: The kernel size is intentionally restricted at this time; see
> +commit message define Device/glinet_gl-x1200-nor-nand
> + $(Device/glinet_gl-x1200-common)
> + DEVICE_VARIANT := NOR/NAND
> + BLOCKSIZE := 128k
> + GL_UBOOT_UBI_OFFSET := 2048k
> + IMAGES += factory.img
> + IMAGE/factory.img := append-kernel | pad-to
> $$$$(GL_UBOOT_UBI_OFFSET) | \
> + append-ubi | check-kernel-size $$$$(GL_UBOOT_UBI_OFFSET)
> + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
> + SUPPORTED_DEVICES += glinet,gl-x1200-nor endef TARGET_DEVICES +=
> +glinet_gl-x1200-nor-nand
> +
> +define Device/glinet_gl-x1200-nor
> + $(Device/glinet_gl-x1200-common)
> + DEVICE_VARIANT := NOR
> + BLOCKSIZE := 64k
> + SUPPORTED_DEVICES += gl-x1200 glinet,gl-x1200
> +glinet,gl-x1200-nor-nand endef TARGET_DEVICES += glinet_gl-x1200-nor
> +
> # fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header +
> 0xff) define Device/netgear_ath79_nand
> DEVICE_VENDOR := NETGEAR
> diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network
> b/target/linux/ath79/nand/base-files/etc/board.d/02_network
> index b2191ee..cd1e0a7 100755
> --- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
> @@ -20,6 +20,11 @@ ath79_setup_interfaces()
> ucidef_add_switch "switch0" \
> "0 at eth0" "2:lan:2" "3:lan:1" "1:wan"
> ;;
> + glinet,gl-x1200-nor|\
> + glinet,gl-x1200-nor-nand)
> + ucidef_add_switch "switch0" \
> + "0 at eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
> "5:wan"
> + ;;
> netgear,wndr3700-v4|\
> netgear,wndr4300|\
> netgear,wndr4300-v2|\
> diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-
> ath10k-caldata b/target/linux/ath79/nand/base-
> files/etc/hotplug.d/firmware/11-ath10k-caldata
> index d5fd3db..02f226c 100644
> --- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-
> caldata
> +++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10
> +++ k-caldata
> @@ -24,6 +24,16 @@ case "$FIRMWARE" in
> ;;
> esac
> ;;
> +"ath10k/pre-cal-pci-0000:00:00.0.bin")
> + case $board in
> + glinet,gl-x1200-nor|\
> + glinet,gl-x1200-nor-nand)
> + caldata_extract "art" 0x5000 0x2f20
> + ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
> + /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
> + ;;
> + esac
> + ;;
> *)
> exit 1
> ;;
> diff --git a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
> b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
> index ea77345..4ea2287 100644
> --- a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh
> @@ -19,7 +19,9 @@ platform_do_upgrade() {
> glinet_nand_nor_do_upgrade "$1"
> ;;
> glinet,gl-ar750s-nor|\
> - glinet,gl-ar750s-nor-nand)
> + glinet,gl-ar750s-nor-nand |\
> + glinet,gl-x1200-nor|\
> + glinet,gl-x1200-nor-nand)
> nand_nor_do_upgrade "$1"
> ;;
> *)
> --
> 2.7.4
>
>
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: openpgp-digital-signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20200412/b309d013/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list