[OpenWrt-Devel] [PATCH] ramips: adding support for OY-0001 Wireless Router
John Crispin
blogic at openwrt.org
Fri Jul 10 07:37:02 EDT 2015
On 10/07/2015 13:27, Karl Palsson wrote:
> Isn't this normally called the "OYE-0001" ? not "OY-0001" ? The website
> and all literature I've seen uses the "OYE-0001" name...
>
> Regardless, in many places, you have not followed the existing
> alphabetical order.
>
there never has been an alphabetic order requirement and many entries
are not alphabetically sorted
> LiWeijian <younfan33 at hotmail.com> wrote:
>> From: Tom Deng <2579131212 at qq.com>
>
>> Adding support for OY-0001 Wireless Router.
>> OY-0001 is a wireless router made by oyewifi.com. Below is the details:
>> MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
>> Signed-off-by: Tom Deng <2579131212 at qq.com>
>> ---
>> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
>> b/target/linux/ramips/base-files/etc/board.d/01_leds
>> index 545bd70..fe3a79d 100755
>> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
>> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
>> @@ -238,6 +238,10 @@ case $board in
>> set_wifi_led "zbtlink:blue:air"
>> set_usb_led "zbtlink:blue:usb"
>> ;;
>> + oy-0001)
>> + ucidef_set_led_default "power" "power" "oy:green:power" "1"
>> + set_wifi_led "oy:green:wifi"
>> + ;;
>> wr8305rt)
>> ucidef_set_led_default "power" "power" "wr8305rt:sys" "1"
>> set_usb_led "wr8305rt:usb"
>> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
>> b/target/linux/ramips/base-files/etc/board.d/02_network
>> index bc1fc01..9fb3535 100755
>> --- a/target/linux/ramips/base-files/etc/board.d/02_network
>> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
>> @@ -139,6 +139,7 @@ ramips_setup_interfaces()
>> mzk-750dhp | \
>> whr-300hp2 | \
>> whr-600d | \
>> + oy-0001 | \
>> wsr-600 | \
>> wsr-1166 | \
>> wt1520 | \
>> @@ -283,6 +284,11 @@ ramips_setup_macs()
>> wan_mac=$(mtd_get_mac_binary devdata 7)
>> ;;
>
>> + oy-0001)
>> + lan_mac=$(mtd_get_mac_binary factory 40)
>> + wan_mac=$(mtd_get_mac_binary factory 46)
>> + ;;
>> +
>> w306r-v20)
>> lan_mac=$(cat /sys/class/net/eth0/address)
>> wan_mac=$(macaddr_add "$lan_mac" 5)
>> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
>> b/target/linux/ramips/base-files/lib/ramips.sh
>> index d2a1856..3d40ab9 100755
>> --- a/target/linux/ramips/base-files/lib/ramips.sh
>> +++ b/target/linux/ramips/base-files/lib/ramips.sh
>> @@ -400,6 +400,9 @@ ramips_board_detect() {
>> *"Zbtlink ZBT-WA05")
>> name="zbt-wa05"
>> ;;
>> + *"OY-0001")
>> + name="oy-0001"
>> + ;;
>> *"ZBT WR8305RT")
>> name="wr8305rt"
>> ;;
>> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> index cedd62b..8f45a84 100755
>> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> @@ -116,6 +116,7 @@ platform_check_image() {
>> wr6202 |\
>> wr8305rt |\
>> wrtnode |\
>> + oy-0001 |\
>> wt1520 |\
>> wt3020 |\
>> x5 |\
>> diff --git a/target/linux/ramips/dts/OY-0001.dts
>> b/target/linux/ramips/dts/OY-0001.dts
>> new file mode 100644
>> index 0000000..48b7099
>> --- /dev/null
>> +++ b/target/linux/ramips/dts/OY-0001.dts
>> @@ -0,0 +1,123 @@
>> +/dts-v1/;
>> +
>> +/include/ "mt7620a.dtsi"
>> +
>> +/ {
>> + compatible = "ralink,mt7620a-soc";
>> + model = "OY-0001";
>> +
>> + chosen {
>> + bootargs = "console=ttyS0,115200";
>> + };
>> +
>> + palmbus at 10000000 {
>> + gpio2: gpio at 660 {
>> + status = "okay";
>> + };
>> +
>> + gpio3: gpio at 688 {
>> + status = "okay";
>> + };
>> +
>> + spi at b00 {
>> + status = "okay";
>> +
>> + m25p80 at 0 {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "w25q128";
>> + reg = <0 0>;
>> + linux,modalias = "m25p80", "w25q128";
>> + spi-max-frequency = <10000000>;
>> +
>> + partition at 0 {
>> + label = "u-boot";
>> + reg = <0x0 0x30000>;
>> + read-only;
>> + };
>> +
>> + partition at 30000 {
>> + label = "u-boot-env";
>> + reg = <0x30000 0x10000>;
>> + read-only;
>> + };
>> +
>> + factory: partition at 40000 {
>> + label = "factory";
>> + reg = <0x40000 0x10000>;
>> + read-only;
>> + };
>> +
>> + partition at 50000 {
>> + label = "firmware";
>> + reg = <0x50000 0xfb0000>;
>> + };
>> +
>> + };
>> + };
>> + };
>> +
>> + pinctrl {
>> + state_default: pinctrl0 {
>> + gpio {
>> + ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "wled", "nd_sd";
>> + ralink,function = "gpio";
>> + };
>> + };
>> + };
>> +
>> + ethernet at 10100000 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&ephy_pins>;
>> +
>> + ralink,port-map = "llllw";
>> + };
>> +
>> + gsw at 10110000 {
>> + ralink,port4 = "ephy";
>> + };
>> +
>> + wmac at 10180000 {
>> + ralink,mtd-eeprom = <&factory 0>;
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> + powerled {
>> + label = "oy:green:power";
>> + gpios = <&gpio0 9 1>;
>> + };
>> + wifiled {
>> + label = "oy:green:wifi";
>> + gpios = <&gpio3 0 1>;
>> + };
>> + };
>> +
>> + sdhci at 10130000 {
>> + status = "okay";
>> + };
>> +
>> + ehci at 101c0000 {
>> + status = "okay";
>> + };
>> +
>> + ohci at 101c1000 {
>> + status = "okay";
>> + };
>> +
>> + pcie at 10140000 {
>> + status = "okay";
>> + };
>> +
>> + gpio-keys-polled {
>> + compatible = "gpio-keys-polled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + poll-interval = <20>;
>> + s1 {
>> + label = "reset";
>> + gpios = <&gpio0 1 1>;
>> + linux,code = <0x198>;
>> + };
>> + };
>> +};
>> diff --git a/target/linux/ramips/image/Makefile
>> b/target/linux/ramips/image/Makefile
>> index 0c28216..2fe5fdd 100644
>> --- a/target/linux/ramips/image/Makefile
>> +++ b/target/linux/ramips/image/Makefile
>> @@ -866,6 +866,7 @@ Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l
>> na930_mtd_size=20971520
>> Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
>> Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
>> +Image/Build/Profile/OY-0001=$(call BuildFirmware/Default16M/$(1),$(1),oy-0001,OY-0001)
>> Image/Build/Profile/Y1=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1,Y1)
>> Image/Build/Profile/Y1S=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1s,Y1S)
>> Image/Build/Profile/MLW221=$(call BuildFirmware/Default16M/$(1),$(1),mlw221,MLW221)
>> @@ -899,6 +900,7 @@ define Image/Build/Profile/Default
>> $(call Image/Build/Profile/WHR1166D,$(1))
>> $(call Image/Build/Profile/MZK-750DHP,$(1))
>> $(call Image/Build/Profile/NA930,$(1))
>> + $(call Image/Build/Profile/OY-0001,$(1))
>> $(call Image/Build/Profile/Y1,$(1))
>> $(call Image/Build/Profile/Y1S,$(1))
>> $(call Image/Build/Profile/MLW221,$(1))
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel at lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
>
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list