[PATCH v3] realtek: ensure output drivers are enabled in RTL8231

Paul Fertser fercerpav at gmail.com
Fri Oct 1 02:37:11 PDT 2021


The bootloader can leave the GPIO expander in a state which doesn't have
output drivers enabled so GPIOs will properly work for input but output
operations will have no effect.

To avoid disrupting the boot in case the bootloader left direction and
data registers in an inconsistent state (e.g. pulling SoC's reset to 0)
reconfigure everything as input.

Reviewed-by: Sander Vanheule <sander at svanheule.net>
Signed-off-by: Paul Fertser <fercerpav at gmail.com>
---

Notes:
    Changes from v2:
     - Fix 5.10 as well
    
    Changes from v1:
     - Fix comment to mention we affect two extra GPIOs
     - Remove unused "v" declaration.

 .../realtek/files-5.10/drivers/gpio/gpio-rtl8231.c   | 12 +++++++-----
 .../realtek/files-5.4/drivers/gpio/gpio-rtl8231.c    | 12 +++++++-----
 2 files changed, 14 insertions(+), 10 deletions(-)

diff --git a/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c b/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c
index a8ffcdc31368..f4f5621e0c1b 100644
--- a/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c
+++ b/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c
@@ -239,8 +239,6 @@ void rtl8231_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
 
 int rtl8231_init(struct rtl8231_gpios *gpios)
 {
-	u32 v;
-
 	pr_info("%s called, MDIO bus ID: %d\n", __func__, gpios->smi_bus_id);
 
 	gpios->reg_cached = 0;
@@ -254,11 +252,15 @@ int rtl8231_init(struct rtl8231_gpios *gpios)
 		sw_w32_mask(3, 1, RTL838X_DMY_REG5);
 	}
 
-	/* Select GPIO functionality for pins 0-34 */
+	/* Select GPIO functionality and force input direction for pins 0-36 */
 	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(0), 0xffff);
+	rtl8231_write(gpios, RTL8231_GPIO_DIR(0), 0xffff);
 	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(16), 0xffff);
-	v = rtl8231_read(gpios, RTL8231_GPIO_PIN_SEL(32));
-	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), v | 0x7);
+	rtl8231_write(gpios, RTL8231_GPIO_DIR(16), 0xffff);
+	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), 0x03ff);
+
+	/* Set LED_Start to enable drivers for output mode */
+	rtl8231_write(gpios, RTL8231_LED_FUNC0, 1 << 1);
 
 	return 0;
 }
diff --git a/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c b/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c
index a8ffcdc31368..f4f5621e0c1b 100644
--- a/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c
+++ b/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c
@@ -239,8 +239,6 @@ void rtl8231_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
 
 int rtl8231_init(struct rtl8231_gpios *gpios)
 {
-	u32 v;
-
 	pr_info("%s called, MDIO bus ID: %d\n", __func__, gpios->smi_bus_id);
 
 	gpios->reg_cached = 0;
@@ -254,11 +252,15 @@ int rtl8231_init(struct rtl8231_gpios *gpios)
 		sw_w32_mask(3, 1, RTL838X_DMY_REG5);
 	}
 
-	/* Select GPIO functionality for pins 0-34 */
+	/* Select GPIO functionality and force input direction for pins 0-36 */
 	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(0), 0xffff);
+	rtl8231_write(gpios, RTL8231_GPIO_DIR(0), 0xffff);
 	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(16), 0xffff);
-	v = rtl8231_read(gpios, RTL8231_GPIO_PIN_SEL(32));
-	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), v | 0x7);
+	rtl8231_write(gpios, RTL8231_GPIO_DIR(16), 0xffff);
+	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), 0x03ff);
+
+	/* Set LED_Start to enable drivers for output mode */
+	rtl8231_write(gpios, RTL8231_LED_FUNC0, 1 << 1);
 
 	return 0;
 }
-- 
2.17.1




More information about the openwrt-devel mailing list