[OpenWrt-Devel] [PATCH] CC: ramips: Backport support for Netgear EX2700
Joseph C. Lehner
joseph.c.lehner at gmail.com
Thu Feb 11 13:07:10 EST 2016
This patch adds support for the Netgear EX2700 in Chaos Calmer and
builds an approriate sysupgrade image (backported from my earlier
submission).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner at gmail.com>
---
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5946f98..5327d00 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -114,6 +114,10 @@ case $board in
esr-9753)
set_wifi_led "rt2800pci-phy0::radio"
;;
+ ex2700)
+ ucidef_set_led_default "power_r" "POWER (red)" "ex2700:red:power" "0"
+ set_wifi_led "ex2700:green:router"
+ ;;
f5d8235-v1)
set_usb_led "f5d8235-v1:blue:storage"
;;
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index d7d016b..a78912d 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -113,7 +113,8 @@ ramips_setup_interfaces()
ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t"
;;
- cf-wr800n)
+ cf-wr800n|\
+ ex2700)
ucidef_set_interface_lan "eth0.1"
ucidef_add_switch "switch0" "1" "1"
ucidef_add_switch_vlan "switch0" "1" "4 6t"
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index a7e2501..6474ebd 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -63,6 +63,9 @@ get_status_led() {
esr-9753)
status_led="esr-9753:orange:power"
;;
+ ex2700)
+ status_led="ex2700:red:power"
+ ;;
f5d8235-v2)
status_led="f5d8235v2:blue:router"
;;
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 4141ddd..8dc05b0 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -223,6 +223,9 @@ ramips_board_detect() {
*"Netgear WNCE2001")
name="wnce2001"
;;
+ *"Netgear EX2700")
+ name="ex2700"
+ ;;
*"NexAira BC2")
name="bc2"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 2f64d8c..a3d0175 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -49,6 +49,7 @@ platform_check_image() {
dir-620-d1 | \
dir-810l | \
e1700 | \
+ ex2700 |\
esr-9753 | \
f7c027 | \
fonera20n | \
diff --git a/target/linux/ramips/dts/EX2700.dts b/target/linux/ramips/dts/EX2700.dts
new file mode 100644
index 0000000..da98bd8
--- /dev/null
+++ b/target/linux/ramips/dts/EX2700.dts
@@ -0,0 +1,148 @@
+/*
+ * Device Tree file for the Netgear EX2700
+ *
+ * Copyright (C) 2016 Joseph C. Lehner <joseph.c.lehner at gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+ compatible = "ralink,mt7620a-soc";
+ model = "Netgear EX2700";
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ palmbus at 10000000 {
+
+ gpio0: gpio at 600 {
+ status = "okay";
+ };
+
+ gpio1: gpio at 638 {
+ status = "okay";
+ };
+
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mx25l3205d";
+ reg = <0 0>;
+ linux,modalias = "m25p80", "mx25l3205d";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "firmware";
+ reg = <0x40000 0x3b0000>;
+ };
+
+ art: partition at 3f0000 {
+ label = "art";
+ reg = <0x3f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+ };
+
+ ethernet at 10100000 {
+ mtd-mac-address = <&art 0x0>;
+ };
+
+ wmac at 10180000 {
+ ralink,mtd-eeprom = <&art 0x1000>;
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ default {
+ // spi refclk: pins 37, 38, 39
+ // uartf: pins 8, 9, 10, 11, 12, 13, 14
+ // i2c: pins 1, 2
+ ralink,group = "i2c", "uartf", "spi refclk";
+ ralink,function = "gpio";
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power_g {
+ label = "ex2700:green:power";
+ gpios = <&gpio0 9 1>;
+ default-state = "on";
+ };
+
+ power_r {
+ label = "ex2700:red:power";
+ gpios = <&gpio0 11 1>;
+ };
+
+ device_g {
+ label = "ex2700:green:device";
+ gpios = <&gpio0 13 1>;
+ };
+
+ device_r {
+ label = "ex2700:red:device";
+ gpios = <&gpio0 10 1>;
+ };
+
+ router_g {
+ label = "ex2700:green:router";
+ gpios = <&gpio0 12 1>;
+ };
+
+ router_r {
+ label = "ex2700:red:router";
+ gpios = <&gpio0 14 1>;
+ };
+
+ wps {
+ label = "ex2700:green:wps";
+ gpios = <&gpio1 15 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 1 1>;
+ linux,code = <0x198>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 2 1>;
+ linux,code = <0x211>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 0d762ba..bdb5844 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -855,6 +855,7 @@ endif
#
Image/Build/Profile/E1700=$(call BuildFirmware/UMedia/$(1),$(1),e1700,E1700,0x013326)
+Image/Build/Profile/EX2700=$(call BuildFirmware/Default4M/$(1),$(1),ex2700,EX2700)
Image/Build/Profile/MT7620a=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a,MT7620a)
Image/Build/Profile/MT7620a_MT7610e=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7610e,MT7620a_MT7610e)
Image/Build/Profile/MT7620a_MT7530=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7530,MT7620a_MT7530)
@@ -893,6 +894,7 @@ Image/Build/Profile/MicroWRT=$(call BuildFirmware/CustomFlash/$(1),$(1),microwrt
ifeq ($(SUBTARGET),mt7620)
define Image/Build/Profile/Default
$(call Image/Build/Profile/E1700,$(1))
+ $(call Image/Build/Profile/EX2700,$(1))
$(call Image/Build/Profile/MT7620a,$(1))
$(call Image/Build/Profile/MT7620a_MT7610e,$(1))
$(call Image/Build/Profile/MT7620a_MT7530,$(1))
diff --git a/target/linux/ramips/mt7620/profiles/netgear.mk b/target/linux/ramips/mt7620/profiles/netgear.mk
new file mode 100644
index 0000000..d1b073a
--- /dev/null
+++ b/target/linux/ramips/mt7620/profiles/netgear.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2016 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/EX2700
+ NAME:=Netgear EX2700
+ PACKAGES:=-kmod-usb-core -kmod-usb2 -kmod-usb-ohci -kmod-ledtrig-usbdev
+endef
+
+define Profile/EX2700/Description
+ Support for Netgear EX2700
+endef
+$(eval $(call Profile,EX2700))
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list