[OpenWrt-Devel] lantiq v3.18

John Crispin blogic at openwrt.org
Mon Feb 23 13:49:11 EST 2015


could you also show me the bootlog on 3.14 please

On 22/02/2015 20:40, Roger Pueyo Centelles wrote:
> Sure.
> 
> U-Boot 2013.10-openwrt5-00014-g0b78b5c-dirty (Mar 11 2014 - 22:56:27) arv7519rw
> 
> Board: Lantiq ARV7519RW VRX200 Family Board
> SoC:   Lantiq VRX288 v1.1
> CPU:   500 MHz
> IO:    250 MHz
> BUS:   250 MHz
> BOOT:  NOR
> DRAM:  128 MiB
> Flash: 32 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Net:   ltq-eth
> Hit any key to stop autoboot:  0
> ## Booting kernel from Legacy Image at b0080000 ...
>    Image Name:   MIPS OpenWrt Linux-3.18.7
>    Created:      2015-02-22  11:56:23 UTC
>    Image Type:   MIPS Linux Kernel Image (lzma compressed)
>    Data Size:    1546993 Bytes = 1.5 MiB
>    Load Address: 80002000
>    Entry Point:  80002000
>    Verifying Checksum ... OK
>    Uncompressing Kernel Image ... OK
> 
> Starting kernel ...
> 
> [    0.000000] Linux version 3.18.7 (lordroger at xeon) (gcc version
> 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44507) ) #1 Sun Feb 22 12:56:14
> CET 2015
> [    0.000000] SoC: VR9 rev 1.1
> [    0.000000] bootconsole [early0] enabled
> [    0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
> [    0.000000] MIPS: machine is ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT
> [    0.000000] Determined physical RAM map:
> [    0.000000]  memory: 08000000 @ 00000000 (usable)
> [    0.000000] Initrd not found or empty - disabling initrd
> [    0.000000] Zone ranges:
> [    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
> [    0.000000] Movable zone start for each node
> [    0.000000] Early memory node ranges
> [    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
> [    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
> [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
> linesize 32 bytes
> [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 32512
> [    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
> [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
> [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> [    0.000000] Writing ErrCtl register=00044751
> [    0.000000] Readback ErrCtl register=00044751
> [    0.000000] Memory: 125044K/131072K available (3312K kernel code,
> 147K rwdata, 932K rodata, 196K init, 205K bss, 6028K reserved)
> [    0.000000] NR_IRQS:256
> [    0.000000] CPU Clock: 500MHz
> [    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
> [    0.032000] pid_max: default: 32768 minimum: 301
> [    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.044000] pinctrl core: initialized pinctrl subsystem
> [    0.048000] NET: Registered protocol family 16
> [    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
> [    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7,
> channels: 28
> [    0.064000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
> [    0.088000] usbcore: registered new interface driver usbfs
> [    0.092000] usbcore: registered new interface driver hub
> [    0.096000] usbcore: registered new device driver usb
> [    0.100000] Switched to clocksource MIPS
> [    0.104000] NET: Registered protocol family 2
> [    0.108000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.116000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.124000] TCP: Hash tables configured (established 1024 bind 1024)
> [    0.128000] TCP: reno registered
> [    0.132000] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [    0.136000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [    0.144000] NET: Registered protocol family 1
> [    0.148000] gptu: totally 6 16-bit timers/counters
> [    0.152000] gptu: misc_register on minor 63
> [    0.156000] gptu: succeeded to request irq 126
> [    0.164000] gptu: succeeded to request irq 127
> [    0.168000] gptu: succeeded to request irq 128
> [    0.172000] gptu: succeeded to request irq 129
> [    0.176000] gptu: succeeded to request irq 130
> [    0.180000] gptu: succeeded to request irq 131
> [    0.184000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy22f_a1x.bin
> [    0.192000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7900000
> [    0.200000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7900000
> [    0.308000] futex hash table entries: 256 (order: -1, 3072 bytes)
> [    0.316000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [    0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
> (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> [    0.332000] msgmni has been set to 244
> [    0.336000] io scheduler noop registered
> [    0.340000] io scheduler deadline registered (default)
> [    0.344000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112,
> base_baud = 0) is a lantiq,asc
> [    0.352000] console [ttyLTQ0] enabled
> [    0.352000] console [ttyLTQ0] enabled
> [    0.360000] bootconsole [early0] disabled
> [    0.360000] bootconsole [early0] disabled
> [    0.368000] lantiq nor flash device: 02000000 at 10000000
> [    0.372000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank.
> Manufacturer ID 0x0000c2 Chip ID 0x00227e
> [    0.384000] Amd/Fujitsu Extended Query Table at 0x0040
> [    0.388000]   Amd/Fujitsu Extended Query version 1.3.
> [    0.392000] number of CFI chips: 1
> [    0.396000] lantiq nor flash device: 02000000 at 16000000
> [    0.404000] ltq-nor 10000000.nor-boot: probing failed
> [    0.512000] libphy: lantiq,xrx200-mdio: probed
> [    0.532000] net-xrx200: invalid MAC, using random
> [    0.600000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3]
> (phy_addr=0:00, irq=-1)
> [    0.668000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
> (phy_addr=0:13, irq=-1)
> [    0.736000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
> (phy_addr=0:14, irq=-1)
> [    0.804000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
> (phy_addr=0:11, irq=-1)
> [    0.872000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
> (phy_addr=0:12, irq=-1)
> [    0.880000] wdt 1f8803f0.watchdog: Init done
> [    0.884000] TCP: cubic registered
> [    0.884000] NET: Registered protocol family 17
> [    0.888000] bridge: automatic filtering via arp/ip/ip6tables has
> been deprecated. Update your scripts to load br_netfilter if you need
> this.
> [    0.904000] 8021q: 802.1Q VLAN Support v1.8
> [    0.908000] UBIFS error (pid 1): ubifs_mount: cannot open
> "ubi0:rootfs", error -19
> [    0.916000] VFS: Cannot open root device "(null)" or
> unknown-block(0,0): error -6
> [    0.924000] Please append a correct "root=" boot option; here are
> the available partitions:
> [    0.932000] Kernel panic - not syncing: VFS: Unable to mount root
> fs on unknown-block(0,0)
> [    0.932000] ---[ end Kernel panic - not syncing: VFS: Unable to
> mount root fs on unknown-block(0,0)
> [   33.092000] random: nonblocking pool is initialized
> 
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list