[OpenWrt-Devel] ar71xx update to v3.18

[Paul Blazejowski]

On Sun, 2015-02-15 at 20:49 +0100, John Crispin wrote:
> Hi,
> 
> i just pushed the v3.18 support for ar71xx. i have tested this on
> carambola2, unifi and wndr4300. the default is still at 3.14. please
> start testing on more hardware.
> 
> to do so you need to set the kernel to 3.18 in
> target/linux/ar71xx/Makefile as the default is still at 3.14.
> 
> 902-unaligned_access_hacks.patch was rebased, however there might be new
> places in the stack that need the hack applied. testing for this is also
> welcome.
> 
> 	John
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel

Compiled just fine here on wndr3700v4. Sysupgraded my router via LuCI
and immediately noticed two things:

1. no wifi

[   21.670000] cfg80211: Calling CRDA to update world regulatory domain
[   21.670000] cfg80211: World regulatory domain updated:
[   21.680000] cfg80211:  DFS Master region: unset
[   21.680000] cfg80211:   (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[   21.690000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[   21.700000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[   21.710000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm), (N/A)
[   21.720000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[   21.730000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz,
160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   21.730000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[   21.740000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[   21.750000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[   22.170000] ath9k ar934x_wmac: Direct firmware load for
soc_wmac.eeprom failed with error -2
[   22.180000] ath: phy0: Unable to load EEPROM file soc_wmac.eeprom
[   22.190000] ath9k ar934x_wmac: failed to initialize device
[   22.190000] ath9k: probe of ar934x_wmac failed with error -22
[   22.200000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   22.220000] ath9k 0000:00:00.0: Direct firmware load for
pci_wmac0.eeprom failed with error -2
[   22.230000] ath: phy1: Unable to load EEPROM file pci_wmac0.eeprom
[   22.230000] ath9k 0000:00:00.0: Failed to initialize device
[   22.240000] ath9k: probe of 0000:00:00.0 failed with error -22
[   29.760000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready


2. bridge warning

bridge: automatic filtering via arp/ip/ip6tables has been deprecated.
Update your scripts to load br_netfilter if you need this.

regular ethX ports (lan side) work fine over wire.
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel