[OpenWrt-Devel] raspberry pi v3.19

[Álvaro Fernández Rojas]

Okay, it's working now:
http://files.noltari.es/openwrt/bcm2708/bcm2708_3-18_log.txt

Patches:
http://files.noltari.es/openwrt/bcm2708/brcm2708_3-18.tgz

El 10/02/2015 a las 13:10, Álvaro Fernández Rojas escribió:
> I could finally boot 3.18 by loading the rootfs from USB:
> http://pastebin.com/b4dX0X7B
> 
> Everything seems to be working fine, still no clue about the SD issues...
> http://pastebin.com/G61ALvLX
> 
> El 10/02/2015 a las 11:09, Álvaro Fernández Rojas escribió:
>> The pins you said are the right ones. However, if anything fails before the kernel is booted you won't get any output. You could try booting a 3.14 image and check if you are properly connected to the uart.
>>
>> It may be some wrong configuration related to the recently added DT support, which expects a DTB and since no DTB is passed from the bootloader, the kernel crashes before any output.
>>
>>> El 10/2/2015, a las 6:29, John Crispin <blogic at openwrt.org> escribió:
>>>
>>> ok, so uart, how do you connect it ?
>>>
>>>> On 10/02/2015 02:02, Álvaro Fernández Rojas wrote:
>>>> I tried adding support for 3.18 and I have issues booting the raspberry. There must be something wrong with the new mmc driver, because it detects the SD card insertions/extractiones, but doesn't read the partitions:
>>>> http://pastebin.com/GWFYrXnT
>>>>
>>>> My patches:
>>>> http://files.noltari.es/openwrt/bcm2708/brcm2708_3-18.tgz
>>>>
>>>> Regards,
>>>> Álvaro.
>>>>
>>>>> El 09/02/2015 a las 18:12, Florian Fainelli escribió:
>>>>>> On Feb 9, 2015 4:25 AM, "John Crispin" <blogic at openwrt.org <mailto:blogic at openwrt.org>> wrote:
>>>>>>
>>>>>> Hi,
>>>>>>
>>>>>> i synced our rpi port with the upstream tree on github. it boots and i
>>>>>> can see the coloured palette test pic on the hdmi, however ethernet
>>>>>> fails to come up. i attached a uart just to find out that my rpi is
>>>>>> either broken or i am connecting it wrong.
>>>>>>
>>>>>> has anyone managed to get uart working ? to my understanding i need to
>>>>>> connect pin6 to gnd and use 8 and 10 for the 2 data lines. should i see
>>>>>> output from the bootloader prior to board detecting/loading the sd card
>>>>>
>>>>> You will not get any UART output prior to the kernel boot, the GPU boot code does not output anything (at least not in the builds we use).
>>>>>
>>>>> Could you share the boot log to see if there is anything obvious?
>>>>>
>>>>>>
>>>>>>        John
>>>>>> _______________________________________________
>>>>>> openwrt-devel mailing list
>>>>>> openwrt-devel at lists.openwrt.org <mailto:openwrt-devel at lists.openwrt.org>
>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> openwrt-devel mailing list
>>>>> openwrt-devel at lists.openwrt.org
>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel