[OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was: Multiple Wi-Fi client/AP interfaces on one radio)

John kerry kerry9842 at gmail.com
Tue Aug 11 21:29:21 EDT 2015


Yes i able to config using GUI, But when i am configuring GUI i scan and
connect to one AP and then add one more AP mode to it. So finally i will
have wireless configuration.

But i cant keep this config in build option because if i load this
configuration it will load what i connected last time, so next time i cant
scan it anymore it showing the same connected to last AP.




On Wed, Aug 12, 2015 at 1:36 AM, David Lang <david at lang.hm> wrote:

> I thought you said a couple posts ago that you were able to configure it
> through the GUI to work the way you wanted it to, you were just wanting to
> make something the default.
>
> So do you have it working or not?
>
> If you have it working, it should keep working after a reboot. What are
> you meaning when you say that you want to change the default?
>
> Are you meaning that you want to create an image that will behave this way
> when you do a factory reset (or when you first flash it)? If so, then you
> need to take your working config and make it part of your image via the
> files/ mechansim.
>
> If you are meaning something else, I'm still not understanding what you
> are trying to do.
>
> David Lang
>
>
>
> On Tue, 11 Aug 2015, John kerry wrote:
>
> Date: Tue, 11 Aug 2015 21:20:58 +0800
>>
>> From: John kerry <kerry9842 at gmail.com>
>> To: David Lang <david at lang.hm>
>> Cc: Alex Weedy <weedy2887 at gmail.com>,
>>     OpenWrt Development List <openwrt-devel at lists.openwrt.org>
>> Subject: Re: [OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was:
>> Multiple
>>     Wi-Fi client/AP interfaces on one radio)
>>
>> Hi,
>>
>> How to config wireless config file for repeater mode. I am not able to
>> config.
>>
>> On Tue, Aug 11, 2015 at 5:34 PM, John kerry <kerry9842 at gmail.com> wrote:
>>
>> When i load firmware the wireless config will be like below:
>>>
>>> config wifi-device 'wifi0'
>>>         option type 'qcawifi'
>>>         option macaddr '00:26:75:bd:37:24'
>>>         option hwmode '11ng'
>>>         option txpower '16'
>>>         option htmode 'HT20'
>>>         option disabled '0'
>>>         option channel '1'
>>>
>>> config wifi-iface
>>>         option device 'wifi0'
>>>         option mode 'ap'
>>>         option ssid 'Test_ap'
>>>         option network 'lan'
>>>         option encryption 'psk2'
>>>         option key 'Test_ap'
>>>         option wds '1'
>>>
>>> so it works as Access point, i can connect to it any devices. When i scan
>>> it shows me list of devices then connect to anyone. then the wireless
>>> config  will becomes like below:
>>>
>>> config wifi-device 'wifi0'
>>>         option type 'qcawifi'
>>>         option macaddr '00:26:75:bd:37:24'
>>>         option hwmode '11ng'
>>>         option txpower '16'
>>>         option htmode 'HT20'
>>>         option disabled '0'
>>>         option channel '1'
>>>
>>> config wifi-iface
>>>         option network 'wwan'
>>>         option ssid 'D-link-Router'
>>>         option encryption 'psk2'
>>>         option device 'wifi0'
>>>         option mode 'sta'
>>>         option key '0010069039'
>>>         option wds '1'
>>>
>>> Then i add one more ap mode so wireless config becomes,
>>> config wifi-device 'wifi0'
>>>         option type 'qcawifi'
>>>         option macaddr '00:26:75:bd:37:24'
>>>         option hwmode '11ng'
>>>         option txpower '16'
>>>         option htmode 'HT20'
>>>         option disabled '0'
>>>         option channel '1'
>>>
>>> config wifi-iface
>>>        option network 'wwan'
>>>         option ssid 'D-link-Router'
>>>         option encryption 'psk2'
>>>         option device 'wifi0'
>>>         option mode 'sta'
>>>         option key '0010069039'
>>>         option wds '1'
>>>
>>> config wifi-iface
>>>         option device 'wifi0'
>>>         option mode 'ap'
>>>         option ssid 'Test_ap'
>>>         option network 'lan'
>>>         option encryption 'psk2'
>>>         option key 'Test_ap'
>>>         option wds '1'
>>>
>>> This i added manually one ap mode.
>>>
>>> So if i copy this config file, build and load this firmware, its load
>>> what
>>> it was there so it shows one client which i was connected last time and
>>> one
>>> AP which i added.
>>>
>>> But now i cannot scan anymore and connect to new router instead of old
>>> client.
>>>
>>> This is the problem i am facing.
>>>
>>> Basically i need to configure the wireless file for repeater mode.
>>>
>>> So after connecting to another router this SSID still should be there and
>>> other device can connect to it.
>>>
>>> On Tue, Aug 11, 2015 at 4:30 PM, David Lang <david at lang.hm> wrote:
>>>
>>> you have a working config
>>>>
>>>> but you want to do something by default
>>>>
>>>> what you want to do is different at different times.
>>>>
>>>> what is it that you want to be the default? when do you want this
>>>> default
>>>> to apply? This isn't clear.
>>>>
>>>> David Lang
>>>>
>>>> On Tue, 11 Aug 2015, John kerry wrote:
>>>>
>>>> Date: Tue, 11 Aug 2015 15:51:38 +0800
>>>>
>>>>> From: John kerry <kerry9842 at gmail.com>
>>>>> To: David Lang <david at lang.hm>
>>>>> Cc: Alex Weedy <weedy2887 at gmail.com>,
>>>>>     OpenWrt Development List <openwrt-devel at lists.openwrt.org>
>>>>> Subject: Re: [OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was:
>>>>> Multiple
>>>>>
>>>>>     Wi-Fi client/AP interfaces on one radio)
>>>>>
>>>>> Yes,
>>>>>
>>>>> i can copy the config and build with this configuration,
>>>>>
>>>>> for example now i have connected to some router, another time we can
>>>>> connect to any router. So how i can fix the settings by default.
>>>>>
>>>>> On Tue, Aug 11, 2015 at 12:45 AM, David Lang <david at lang.hm> wrote:
>>>>>
>>>>> On Mon, 10 Aug 2015, John kerry wrote:
>>>>>
>>>>>>
>>>>>> I followed the same steps and its working too. But this i want in
>>>>>> wireless
>>>>>>
>>>>>> config file, Because i dont want every time to add using GUI. So When
>>>>>>> i
>>>>>>> connect to another router also, no need to add one more. I mean to
>>>>>>> say
>>>>>>> it
>>>>>>> should be in default wireless config file.
>>>>>>>
>>>>>>>
>>>>>>> what do you mean by "default wireless config file"
>>>>>>
>>>>>> Once you have set it from the GUI, it is in the config files. The next
>>>>>> time you boot it will use that config.
>>>>>>
>>>>>> If you mean that you want it in the factory default config (for when
>>>>>> you
>>>>>> first flash the router or do a factory reset), then take the
>>>>>> /etc/config/wireless and /etc/config/network files and add them to
>>>>>> your
>>>>>> build under /files
>>>>>>
>>>>>> David Lang
>>>>>>
>>>>>>
>>>>>> On Mon, Aug 10, 2015 at 6:18 PM, David Lang <david at lang.hm> wrote:
>>>>>>
>>>>>>
>>>>>>> On Mon, 10 Aug 2015, John kerry wrote:
>>>>>>>
>>>>>>>
>>>>>>>> Date: Mon, 10 Aug 2015 18:10:14 +0800
>>>>>>>>
>>>>>>>> From: John kerry <kerry9842 at gmail.com>
>>>>>>>>
>>>>>>>>> To: Alex Weedy <weedy2887 at gmail.com>,
>>>>>>>>>     OpenWrt Development List <openwrt-devel at lists.openwrt.org>
>>>>>>>>> Subject: [OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was:
>>>>>>>>> Multiple
>>>>>>>>> Wi-Fi
>>>>>>>>>     client/AP interfaces on one radio)
>>>>>>>>>
>>>>>>>>> Firstly i configure wireless config as below:
>>>>>>>>>
>>>>>>>>> config wifi-device 'wifi0'
>>>>>>>>>        option type 'qcawifi'
>>>>>>>>>        option macaddr '00:01:11:00:01:00'
>>>>>>>>>        option hwmode '11ng'
>>>>>>>>>        option txpower '17'
>>>>>>>>>        option htmode 'HT20'
>>>>>>>>>        option disabled '0'
>>>>>>>>>        option channel '1'
>>>>>>>>>
>>>>>>>>> config wifi-iface
>>>>>>>>>        option device 'wifi0'
>>>>>>>>>        option mode 'ap'
>>>>>>>>>        option ssid 'Testing_ap'
>>>>>>>>>        option network 'lan'
>>>>>>>>>        option encryption 'psk2'
>>>>>>>>>        option key 'Testing_ap'
>>>>>>>>>
>>>>>>>>> so its SSID was showing and able to connect any device to it.
>>>>>>>>>
>>>>>>>>> Then i scan the device and connect to one of it. While joining the
>>>>>>>>> network
>>>>>>>>> i selected Client(WDS) then the wireless config becomes like below:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> why don't you try following the steps in the video that you posted.
>>>>>>>>>
>>>>>>>>
>>>>>>>> first connect as a client, then add an additional interface and make
>>>>>>>> the
>>>>>>>> second interface the AP for things to connect to.
>>>>>>>>
>>>>>>>> the order may make a difference.
>>>>>>>>
>>>>>>>> David Lang
>>>>>>>>
>>>>>>>>
>>>>>>>> config wifi-device 'wifi0'
>>>>>>>>
>>>>>>>>        option type 'qcawifi'
>>>>>>>>
>>>>>>>>>        option macaddr '00:01:11:00:01:00'
>>>>>>>>>        option hwmode '11ng'
>>>>>>>>>        option txpower '17'
>>>>>>>>>        option htmode 'HT20'
>>>>>>>>>        option disabled '0'
>>>>>>>>>        option channel '1'
>>>>>>>>>
>>>>>>>>> config wifi-iface
>>>>>>>>>        option network 'wwan'
>>>>>>>>>        option ssid 'D_Link_Router'
>>>>>>>>>        option encryption 'psk2'
>>>>>>>>>        option device 'wifi0'
>>>>>>>>>        option mode 'sta'
>>>>>>>>>        option key 'Dlink_Router'
>>>>>>>>>        option wds '1'
>>>>>>>>>
>>>>>>>>> Then  i added one as shown in the video. Now its connected to
>>>>>>>>> router
>>>>>>>>> also
>>>>>>>>> and this add one also showing so i can connect to this also.
>>>>>>>>>
>>>>>>>>> But i am not getting how to keep this in default wireless config.
>>>>>>>>>
>>>>>>>>> Because every time we cant add one to configure like this. It
>>>>>>>>> should
>>>>>>>>> be
>>>>>>>>> like default should be in ap mode so any device we can connect, if
>>>>>>>>> its
>>>>>>>>> connected to another router also that SSID still should be visible
>>>>>>>>> and
>>>>>>>>> able
>>>>>>>>> to connect to this.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>> On Mon, Aug 10, 2015 at 2:57 PM, John kerry <kerry9842 at gmail.com>
>>>>>>>> wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>> When i try to configure based on video, its shows 2 one as client
>>>>>>>>> another
>>>>>>>>>
>>>>>>>>> one as Master but i am not able to enable it . I mean to say
>>>>>>>>> wireless
>>>>>>>>>
>>>>>>>>>> becomes disable. If i enable it using GUI also its not happening.
>>>>>>>>>>
>>>>>>>>>> On Mon, Aug 10, 2015 at 2:55 PM, David Lang <david at lang.hm>
>>>>>>>>>> wrote:
>>>>>>>>>>
>>>>>>>>>> What happens when you try to follow the video?
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Based on your comments, i'm guessing that things don't work when
>>>>>>>>>>> you
>>>>>>>>>>> try
>>>>>>>>>>> and configure the second network and have it with a different
>>>>>>>>>>> SSID
>>>>>>>>>>> than
>>>>>>>>>>> the
>>>>>>>>>>> first network that you put in client mode.
>>>>>>>>>>>
>>>>>>>>>>> Is this correct?
>>>>>>>>>>>
>>>>>>>>>>> David Lang
>>>>>>>>>>>
>>>>>>>>>>> On Mon, 10 Aug 2015, John kerry wrote:
>>>>>>>>>>>
>>>>>>>>>>> Yes, When i am connecting to Another router its changed to Client
>>>>>>>>>>> mode.
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Can i configure this in repeater mode like its shows in below
>>>>>>>>>>> link:
>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> https://www.youtube.com/watch?v=3rbsh2zxPnk
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> _______________________________________________
>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> openwrt-devel mailing list
>>>>>>>>>
>>>>>>>> openwrt-devel at lists.openwrt.org
>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>
>>>
>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150812/3fc8236c/attachment.htm>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list