Issue with ATH10K driver while bringing up mesh interface

[Horse]

Hi

Please try  "insmod ath10k_core.ko rawmode=1"

Thanks

Sridhar Konabathini 於 2016/8/16 下午 12:52 寫道:
> Hi,
>     We are using firmware - fw 10.2.4.70.9-2. while inserting ath10k_core.ko,
> ath10k_pci.ko, we are getting below info.
>
> ----------------------------------------------------------------------------------
>
> root at t1024rdb:/dev/shm# insmod ath10k_core.ko
> root at t1024rdb:/dev/shm# insmod ath10k_pci.ko
> [ 8568.272054] ath10k_pci 0001:03:00.0: pci irq msi interrupts 1 irq_mode 0
> reset_mode 0
> root at t1024rdb:/dev/shm# [ 8569.675804] ath10k_pci 0001:03:00.0: qca988x hw2.0
> (0x4100016c, 0x043202ff sub 0000:0000) fw 10.2.4.70.9-2 fwapi 5 bdapi 1 htt-ver 2.1
> wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,raw-mode
> [ 8569.694974] ath10k_pci 0001:03:00.0: debug 0 debugfs 0 tracing 0 dfs 1 testmode 0
>
> ----------------------------------------------------------------------------------
>
> How to set rawmode=1 while inserting the ath10k module. Can you please help on this.
>
>
> Regards,
>
> Sridhar
>
>
> On Tue, 16 Aug 2016 12:21:48 +0800, Horse wrote
>> Hi
>> Which firmware version are you using now?
>> I think "RAW" mode is disabled after firmware 10.4 no matter CT firmware
>> or official firmware.
>> if you are using firmware 10.2, you might need to add rawmode=1 while
>> insmod ath10k_core.ko
>>
>> Thanks
>>
>> Sridhar Kondabathini 於 2016/8/16 下午 12:06 寫道:
>>> Hi,
>>>      When we are trying to bring up AP to add mesh interfaces on T1024 board with
>>> kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support is
>>> used, then we are getting below error -
>>>
>>> --------------------------------------------------------------------------------
> --
>>> T1024# ifconfig mesh0
>>>
>>> mesh0     Link encap:Ethernet  HWaddr 04:f0:21:1b:7d:b6
>>>             BROADCAST MULTICAST  MTU:1500  Metric:1
>>>             RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>             TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>             collisions:0 txqueuelen:1000
>>>             RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
>>>
>>> T1024# ifconfig mesh0 0.0.0.0 up
>>>
>>> [ 8694.385554] ath10k_pci 0001:03:00.0: must load driver with rawmode=1 to add
> mesh
>>> interfaces
>>>
>>>
>>> --------------------------------------------------------------------------------
> --
>>> How to resolve this issue, can you please help on this.
>>>
>>>
>>> Regards,
>>>
>>> Sridhar Kondabathini,
>>> Research engineer,
>>> PSG lab,
>>> Center for Development Of Telematics
>>> 9480484821.
>>>
>>>
>>>
>>>
>>> Disclaimer:
>>> ----------
>>> This email and any files transmitted with it are confidential and intended
> solely
>>> for
>>> the use of the individual or entity to whom they are addressed.  If you are not
> the
>>> intended recipient you are notified that disclosing, copying, distributing or
> taking
>>> any
>>> action in reliance on the contents of this information is strictly prohibited.
> The
>>> sender does not a
>>>
>>>
>>> _______________________________________________
>>> ath10k mailing list
>>> ath10k at lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/ath10k
>
> Regards,
>
> Sridhar Kondabathini,
> Research engineer,
> PSG lab,
> Center for Development Of Telematics
> 9480484821.
>
>
>
>
> Disclaimer:
> ----------
> This email and any files transmitted with it are confidential and intended solely
> for
> the use of the individual or entity to whom they are addressed.  If you are not the
> intended recipient you are notified that disclosing, copying, distributing or taking
> any
> action in reliance on the contents of this information is strictly prohibited. The
> sender does not a
>
>
> _______________________________________________
> ath10k mailing list
> ath10k at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k