[OpenWrt-Devel] ATH10K VLAN firmware issue

Bruno Antunes baantunes at gmail.com
Fri Nov 4 10:41:14 EDT 2016


On 4 November 2016 at 14:18, Mauro Mozzarelli <openwrt at ezplanet.net> wrote:
> Since the capability is implemented in software you might be testing the
> limit of your router's CPU i/o speed.

By loading the module in rawmode?

The AP is an APU and Sta is an APU2.

>
>
>
> On 04/11/16 14:13, Bruno Antunes wrote:
>>
>> Hi all,
>>
>> Old thread but I think the issue is still present.
>>
>> I'm running a setup with VLANs with WDS and ath10k cards.
>>
>> To make it work both cards must be loaded in rawmode, AP
>> and Sta, and with no security.
>>
>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>
>> Although it works the throughput is very bad.
>> Are there any alternatives to improve the throughput.
>>
>> Best Regards,
>> Bruno
>>
>> On 9 December 2015 at 17:24, voncken <cedric.voncken at acksys.fr> wrote:
>>>
>>>
>>>> -----Message d'origine-----
>>>> De : Ben Greear [mailto:greearb at candelatech.com]
>>>> Envoyé : mercredi 9 décembre 2015 16:34
>>>> À : Cedric VONCKEN; ath10k at lists.infradead.org; linux-wireless
>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>
>>>> This only happens when you use STA  + WDS, or is .1q broken for you in
>>>> other cases as well?
>>>
>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>
>>> Thanks
>>>
>>> Cedric.
>>>
>>>> Thanks,
>>>> Ben
>>>>
>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>
>>>>>      I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>
>>>>>      My client is set in STA + WDS and the netdev is bridged with eth0.
>>>>>      I have a computer with vlan configuration set connected to the STA
>>>>> eth0.
>>>>>
>>>>>      If I try to transmit frames with 802.1q tag, the frames are not
>>>
>>> sent.
>>>>>
>>>>>      I checked with wireless sniffer, and I don't see the frame with
>>>>> VLAN
>>>>> tag (the frames without VLAN tag are sent).
>>>>>
>>>>>      I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>> openwrt, and in all cases I have the same issue.
>>>>>
>>>>>      Thanks for your help.
>>>>>
>>>>>
>>>>> --
>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>> linux-wireless" in the body of a message to majordomo at vger.kernel.org
>>>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>>>>
>>>> --
>>>> Ben Greear <greearb at candelatech.com>
>>>> Candela Technologies Inc  http://www.candelatech.com
>>>
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-wireless"
>>> in
>>> the body of a message to majordomo at vger.kernel.org
>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel at lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list