[OpenWrt-Devel] [PATCH] [generic] ramips: adding support for OYE-0001 Wireless Router

John Crispin blogic at openwrt.org
Tue Jun 30 03:42:15 EDT 2015


Hi,

 the patch is whitespace broken. your email client most likely replaced
all tabs with spaces. please check your mail clients settings and resend
a version with tabs in it

	John

On 30/06/2015 08:37, younfan33 wrote:
> From: Tom Deng <2579131212 at qq.com>  
> 
> Adding support for OYE-0001 Wireless Router.  
> OYE-0001 is a wireless router made by oyewifi.com. Below is the details:  
> MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.  
> Signed-off-by: Tom Deng <2579131212 at qq.com>  
> --- 
> Index: target/linux/ramips/base-files/etc/diag.sh 
> =================================================================== 
> --- target/linux/ramips/base-files/etc/diag.sh    (revision 43797) 
> +++ target/linux/ramips/base-files/etc/diag.sh    (working copy) 
> @@ -185,6 +185,9 @@ 
>      f7c027) 
>          status_led="belkin:orange:status" 
>          ;; 
> +    oye-0001) 
> +        status_led="oye:green:wifi" 
> +        ;; 
>      na930) 
>          status_led="na930:blue:power" 
>          ;; 
> Index: target/linux/ramips/base-files/etc/uci-defaults/01_leds 
> =================================================================== 
> --- target/linux/ramips/base-files/etc/uci-defaults/01_leds    (revision 43797) 
> +++ target/linux/ramips/base-files/etc/uci-defaults/01_leds    (working copy) 
> @@ -198,6 +198,10 @@ 
>          set_wifi_led "zbtlink:blue:air" 
>          set_usb_led "zbtlink:blue:usb" 
>          ;; 
> +    oye-0001) 
> +        ucidef_set_led_default "power" "power" "oye:green:power" "1" 
> +        set_wifi_led "oye:green:wifi" 
> +        ;; 
>      wr8305rt) 
>          ucidef_set_led_default "power" "power" "wr8305rt:sys" "1" 
>          set_usb_led "wr8305rt:usb" 
> Index: target/linux/ramips/base-files/etc/uci-defaults/02_network 
> =================================================================== 
> --- target/linux/ramips/base-files/etc/uci-defaults/02_network    (revision 43797) 
> +++ target/linux/ramips/base-files/etc/uci-defaults/02_network    (working copy) 
> @@ -103,6 +103,7 @@ 
>      dir-615-h1 | \ 
>      hlk-rm04 | \ 
>      mzk-w300nh2 | \ 
> +    oye-0001 | \ 
>      mzk-750dhp) 
>          ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" 
>          ucidef_add_switch "switch0" "1" "1" 
> @@ -220,6 +221,11 @@ 
>          wan_mac=$(mtd_get_mac_binary devdata 7) 
>          ;; 
>   
> +    oye-0001) 
> +        lan_mac=$(mtd_get_mac_binary factory 40) 
> +        wan_mac=$(mtd_get_mac_binary factory 46) 
> +        ;; 
> + 
>      w306r-v20) 
>          lan_mac=$(cat /sys/class/net/eth0/address) 
>          wan_mac=$(macaddr_add "$lan_mac" 5) 
> Index: target/linux/ramips/base-files/lib/ramips.sh 
> =================================================================== 
> --- target/linux/ramips/base-files/lib/ramips.sh    (revision 43797) 
> +++ target/linux/ramips/base-files/lib/ramips.sh    (working copy) 
> @@ -322,6 +322,9 @@ 
>      *"Zbtlink ZBT-WA05") 
>          name="zbt-wa05" 
>          ;; 
> +    *"OYE-0001") 
> +        name="oye-0001" 
> +        ;; 
>      *"ZBT WR8305RT") 
>          name="wr8305rt" 
>          ;; 
> Index: target/linux/ramips/base-files/lib/upgrade/platform.sh 
> =================================================================== 
> --- target/linux/ramips/base-files/lib/upgrade/platform.sh    (revision 43797) 
> +++ target/linux/ramips/base-files/lib/upgrade/platform.sh    (working copy) 
> @@ -95,6 +95,7 @@ 
>      wmr300 |\ 
>      wr8305rt |\ 
>      wrtnode |\ 
> +    oye-0001 |\ 
>      x5 |\ 
>      x8 |\ 
>      zbt-wa05 |\ 
> Index: target/linux/ramips/dts/OYE-0001.dts 
> =================================================================== 
> --- target/linux/ramips/dts/OYE-0001.dts    (revision 0) 
> +++ target/linux/ramips/dts/OYE-0001.dts    (revision 0) 
> @@ -0,0 +1,123 @@ 
> +/dts-v1/; 
> + 
> +/include/ "mt7620a.dtsi" 
> + 
> +/ { 
> +    compatible = "ralink,mt7620a-soc"; 
> +    model = "OYE-0001"; 
> + 
> +        chosen { 
> +                bootargs = "console=ttyS0,115200"; 
> +        }; 
> + 
> +    palmbus at 10000000 { 
> +        gpio2: gpio at 660 { 
> +            status = "okay"; 
> +        }; 
> + 
> +        gpio3: gpio at 688 { 
> +            status = "okay"; 
> +        }; 
> + 
> +        spi at b00 { 
> +            status = "okay"; 
> + 
> +            m25p80 at 0 { 
> +                #address-cells = <1>; 
> +                #size-cells = <1>; 
> +                compatible = "w25q128"; 
> +                reg = <0 0>; 
> +                linux,modalias = "m25p80", "w25q128"; 
> +                spi-max-frequency = <10000000>; 
> + 
> +                partition at 0 { 
> +                    label = "u-boot"; 
> +                    reg = <0x0 0x30000>; 
> +                    read-only; 
> +                }; 
> + 
> +                partition at 30000 { 
> +                    label = "u-boot-env"; 
> +                    reg = <0x30000 0x10000>; 
> +                    read-only; 
> +                }; 
> + 
> +                factory: partition at 40000 { 
> +                    label = "factory"; 
> +                    reg = <0x40000 0x10000>; 
> +                    read-only; 
> +                }; 
> + 
> +                partition at 50000 { 
> +                    label = "firmware"; 
> +                    reg = <0x50000 0xfb0000>; 
> +                }; 
> + 
> +            }; 
> +        }; 
> +    }; 
> + 
> +    pinctrl { 
> +        state_default: pinctrl0 { 
> +            gpio { 
> +                ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "wled", "nd_sd"; 
> +                ralink,function = "gpio"; 
> +            }; 
> +        }; 
> +    }; 
> + 
> +    ethernet at 10100000 { 
> +        pinctrl-names = "default"; 
> +        pinctrl-0 = <&ephy_pins>; 
> + 
> +        ralink,port-map = "llllw"; 
> +    }; 
> + 
> +    gsw at 10110000 { 
> +        ralink,port4 = "ephy"; 
> +    }; 
> + 
> +    wmac at 10180000 { 
> +        ralink,mtd-eeprom = <&factory 0>; 
> +    }; 
> + 
> +    gpio-leds { 
> +        compatible = "gpio-leds"; 
> +        powerled { 
> +            label = "oye:green:power"; 
> +            gpios = <&gpio0 9 1>; 
> +        }; 
> +        wifiled { 
> +            label = "oye:green:wifi"; 
> +            gpios = <&gpio3 0 1>; 
> +        }; 
> +    }; 
> + 
> +    sdhci at 10130000 { 
> +        status = "okay"; 
> +    }; 
> + 
> +    ehci at 101c0000 { 
> +        status = "okay"; 
> +    }; 
> + 
> +    ohci at 101c1000 { 
> +        status = "okay"; 
> +    }; 
> + 
> +    pcie at 10140000 { 
> +        status = "okay"; 
> +    }; 
> + 
> +    gpio-keys-polled { 
> +        compatible = "gpio-keys-polled"; 
> +        #address-cells = <1>; 
> +        #size-cells = <0>; 
> +        poll-interval = <20>; 
> +        s1 { 
> +            label = "reset"; 
> +            gpios = <&gpio0 1 1>; 
> +            linux,code = <0x198>; 
> +        }; 
> +    }; 
> +}; 
> Index: target/linux/ramips/image/Makefile 
> =================================================================== 
> --- target/linux/ramips/image/Makefile    (revision 43797) 
> +++ target/linux/ramips/image/Makefile    (working copy) 
> @@ -724,6 +724,7 @@ 
>  na930_mtd_size=20971520 
>  Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size)) 
>  Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP) 
> +Image/Build/Profile/OYE-0001=$(call BuildFirmware/Default16M/$(1),$(1),oye-0001,OYE-0001) 
>  Image/Build/Profile/Y1=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1,Y1) 
>  Image/Build/Profile/Y1S=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1s,Y1S) 
>   
> @@ -740,6 +741,7 @@ 
>      $(call Image/Build/Profile/WHR1166D,$(1)) 
>      $(call Image/Build/Profile/MZK-750DHP,$(1)) 
>      $(call Image/Build/Profile/NA930,$(1)) 
> +    $(call Image/Build/Profile/OYE-0001,$(1)) 
>      $(call Image/Build/Profile/Y1,$(1)) 
>      $(call Image/Build/Profile/Y1S,$(1)) 
>  endef 
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
> 
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list