[OpenWrt-Devel] [PATCH] lantiq: Add support for the BT Home Hub 5A
Martin Blumenstingl
martin.blumenstingl at googlemail.com
Sat Jun 27 19:49:55 EDT 2015
u-boot support depends on the next "upstream" version ([0]) from
Daniel Schwierzeck.
Since the installation process is quite complicated a "how to" was
added to the wiki: [1]
[0] https://github.com/danielschwierzeck/u-boot-lantiq/tree/openwrt/v2014.01-next
[1] http://wiki.openwrt.org/toh/bt/homehub_v5a
Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
.../etc/hotplug.d/firmware/11-ath10k-caldata | 51 ++++
.../lantiq/base-files/etc/uci-defaults/01_leds | 2 +-
.../lantiq/base-files/etc/uci-defaults/02_network | 8 +
.../lantiq/base-files/lib/upgrade/platform.sh | 2 +-
target/linux/lantiq/dts/BTHOMEHUBV5A.dts | 287 +++++++++++++++++++++
target/linux/lantiq/image/Makefile | 3 +
target/linux/lantiq/xrx200/profiles/bt.mk | 9 +
7 files changed, 360 insertions(+), 2 deletions(-)
create mode 100644 target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
create mode 100644 target/linux/lantiq/dts/BTHOMEHUBV5A.dts
create mode 100644 target/linux/lantiq/xrx200/profiles/bt.mk
diff --git a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
new file mode 100644
index 0000000..0d8084f
--- /dev/null
+++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -0,0 +1,51 @@
+#!/bin/sh
+# Based on ar71xx 11-ath10k-caldata and 10-rt2x00-eeprom
+
+ath10k_caldata_die() {
+ echo "ath10k caldata: " "$*"
+ exit 1
+}
+
+ath10k_caldata_extract() {
+ local part=$1
+ local offset=$2
+ local mtd
+
+ . /lib/functions.sh
+
+ mtd=$(find_mtd_part $part)
+ [ -n "$mtd" ] || \
+ ath10k_caldata_die "no mtd device found for partition $part"
+
+ dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=2116 || \
+ ath10k_caldata_die "failed to extract from $mtd"
+}
+
+ath10k_caldata_set_macaddr() {
+ local macaddr=$1
+
+ macaddr_2bin $macaddr | dd of=/lib/firmware/$FIRMWARE \
+ conv=notrunc bs=1 seek=6 count=6
+}
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+. /lib/functions.sh
+. /lib/functions/system.sh
+. /lib/functions/lantiq.sh
+
+case "$FIRMWARE" in
+"ath10k/cal-pci-0000:02:00.0.bin")
+ local board=$(lantiq_board_name)
+ case $board in
+ BTHOMEHUBV5A)
+ local lan_mac=$(mtd_get_mac_binary caldata 4364)
+ local wifi_mac=$(macaddr_add "$lan_mac" 3)
+ ath10k_caldata_extract "caldata" 20480
+ ath10k_caldata_set_macaddr $wifi_mac
+ ;;
+ *)
+ ath10k_caldata_die "board $board is not supported yet"
+ ;;
+ esac
+ ;;
+esac
diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/01_leds b/target/linux/lantiq/base-files/etc/uci-defaults/01_leds
index 8041ac9..3e05eba 100644
--- a/target/linux/lantiq/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/lantiq/base-files/etc/uci-defaults/01_leds
@@ -25,7 +25,7 @@ BTHOMEHUBV2B)
ucidef_set_led_netdev "internet" "internet" "soc:blue:broadband" "pppoa-wan"
ucidef_set_led_usbdev "usb" "usb" "soc:blue:phone" "1-1"
;;
-BTHOMEHUBV3A)
+BTHOMEHUBV3A|BTHOMEHUBV5A)
ucidef_set_led_default "power" "power" "soc:blue:power" "1"
ucidef_set_led_wlan "wifi" "wifi" "soc:blue:wireless" "phy0tpt"
ucidef_set_led_netdev "internet" "internet" "soc:blue:broadband" "pppoa-wan"
diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/02_network b/target/linux/lantiq/base-files/etc/uci-defaults/02_network
index afb8714..6f9d9c0 100644
--- a/target/linux/lantiq/base-files/etc/uci-defaults/02_network
+++ b/target/linux/lantiq/base-files/etc/uci-defaults/02_network
@@ -169,6 +169,14 @@ BTHOMEHUBV2B|BTHOMEHUBV3A)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
+BTHOMEHUBV5A)
+ lan_mac=$(mtd_get_mac_binary caldata 4364)
+ wan_mac=$(macaddr_add "$lan_mac" 1)
+ ucidef_set_interface_lan 'eth0.1'
+ ucidef_add_switch "switch0" "1" "1"
+ ucidef_add_switch_vlan "switch0" "1" "0 1 2 4 6t"
+ ;;
+
VGV7519)
lan_mac=$(mtd_get_mac_binary board_config 22)
wan_mac=$(macaddr_add "$lan_mac" 1)
diff --git a/target/linux/lantiq/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/base-files/lib/upgrade/platform.sh
index 1688d3a..f255e81 100755
--- a/target/linux/lantiq/base-files/lib/upgrade/platform.sh
+++ b/target/linux/lantiq/base-files/lib/upgrade/platform.sh
@@ -7,7 +7,7 @@ platform_check_image() {
local board=$(lantiq_board_name)
case "$board" in
- BTHOMEHUBV2B|BTHOMEHUBV3A|P2812HNUF* )
+ BTHOMEHUBV2B|BTHOMEHUBV3A|BTHOMEHUBV5A|P2812HNUF* )
nand_do_platform_check $board $1
return $?;
;;
diff --git a/target/linux/lantiq/dts/BTHOMEHUBV5A.dts b/target/linux/lantiq/dts/BTHOMEHUBV5A.dts
new file mode 100644
index 0000000..eb77390
--- /dev/null
+++ b/target/linux/lantiq/dts/BTHOMEHUBV5A.dts
@@ -0,0 +1,287 @@
+/dts-v1/;
+
+/include/ "vr9.dtsi"
+
+/ {
+ model = "BTHOMEHUBV5A - BT Home Hub 5A";
+
+ chosen {
+ bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+ };
+
+ memory at 0 {
+ reg = <0x0 0x8000000>;
+ };
+
+ fpi at 10000000 {
+ localbus at 0 {
+ nand-parts at 0 {
+ compatible = "gen_nand", "lantiq,nand-xway";
+ lantiq,cs = <1>;
+ bank-width = <2>;
+ reg = <0 0x0 0x2000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+ partition at 40000 {
+ label = "uboot-env";
+ reg = <0x40000 0x40000>;
+ };
+ caldata: partition at 80000 {
+ label = "caldata";
+ reg = <0x80000 0x20000>;
+ read-only;
+ };
+ partition at a0000 {
+ label = "kernel";
+ reg = <0xa0000 0x200000>;
+ };
+ partition at 2a0000 {
+ label = "ubi";
+ reg = <0x2a0000 0x7d60000>;
+ };
+ };
+ };
+
+ gpio: pinmux at E100B10 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ interrupt-parent = <&icu0>;
+ interrupts = <166 135 66 40 41 42 38>;
+
+ state_default: pinmux {
+ mdio {
+ lantiq,groups = "mdio";
+ lantiq,function = "mdio";
+ };
+ pci_rst {
+ lantiq,pins = "io21";
+ lantiq,output = <1>;
+ lantiq,open-drain;
+ };
+ pcie_rst {
+ lantiq,pins = "io38";
+ lantiq,pull = <0>;
+ lantiq,output = <1>;
+ lantiq,open-drain;
+ };
+ usb_vbus {
+ lantiq,pins = "io33";
+ lantiq,pull = <0>;
+ lantiq,open-drain = <0>;
+ lantiq,output = <1>;
+ };
+ nand_out {
+ lantiq,groups = "nand cle", "nand ale";
+ lantiq,function = "ebu";
+ lantiq,output = <1>;
+ lantiq,open-drain = <0>;
+ lantiq,pull = <0>;
+ };
+ nand_cs1 {
+ lantiq,groups = "nand cs1";
+ lantiq,function = "ebu";
+ lantiq,open-drain = <0>;
+ lantiq,pull = <0>;
+ };
+ };
+ };
+
+ eth at E108000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "lantiq,xrx200-net";
+ reg = < 0xE108000 0x3000 /* switch */
+ 0xE10B100 0x70 /* mdio */
+ 0xE10B1D8 0x30 /* mii */
+ 0xE10B308 0x30 >; /* pmac */
+ interrupt-parent = <&icu0>;
+ interrupts = <73 72>;
+
+ lan: interface at 0 {
+ compatible = "lantiq,xrx200-pdi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ mtd-mac-address = <&caldata 0x110c>;
+ lantiq,switch;
+
+ ethernet at 0 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <0>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet at 1 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <1>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy1>;
+ };
+ ethernet at 2 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <2>;
+ phy-mode = "gmii";
+ phy-handle = <&phy11>;
+ };
+ ethernet at 4 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <4>;
+ phy-mode = "gmii";
+ phy-handle = <&phy13>;
+ };
+ };
+
+ wan: interface at 1 {
+ compatible = "lantiq,xrx200-pdi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ mtd-mac-address = <&caldata 0x110c>;
+ mtd-mac-address-increment = <4>;
+ lantiq,wan;
+
+ ethernet at 5 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <5>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy5>;
+ };
+ };
+
+ mdio at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "lantiq,xrx200-mdio";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0x0>;
+ compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ };
+ phy1: ethernet-phy at 1 {
+ reg = <0x1>;
+ compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ };
+ phy5: ethernet-phy at 5 {
+ reg = <0x5>;
+ compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ };
+ phy11: ethernet-phy at 11 {
+ reg = <0x11>;
+ compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ };
+ phy13: ethernet-phy at 13 {
+ reg = <0x13>;
+ compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+ };
+ };
+ };
+
+ ifxhcd at E101000 {
+ status = "okay";
+ gpios = <&gpio 33 0>;
+ };
+
+ pci at E105400 {
+ status = "okay";
+ lantiq,bus-clock = <33333333>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <0x7000 0 0 1 &icu0 57 1>; /* INT_NUM_IM1_IRL17 = 57 */
+ gpio-reset = <&gpio 21 0>;
+ };
+ };
+
+ gphy-xrx200 {
+ compatible = "lantiq,phy-xrx200";
+ firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
+ firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
+ phys = [ 00 01 ];
+ };
+
+ ath9k_eep {
+ compatible = "ath9k,eeprom";
+ ath,eep-flash = <&caldata 0x1000>;
+ ath,mac-offset = <0x110c>;
+ ath,mac-increment = <2>;
+ ath,pci-slot = <0xe>; /* 14 */
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <100>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 2 1>;
+ linux,code = <0x198>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 25 1>;
+ linux,code = <0x211>;
+ };
+
+ restart {
+ label = "restart";
+ gpios = <&gpio 39 1>;
+ linux,code = <0x198>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ broadband-red {
+ label = "soc:red:broadband";
+ gpios = <&gpio 0 1>;
+ };
+ broadband-green {
+ label = "soc:green:broadband";
+ gpios = <&gpio 3 1>;
+ };
+ broadband-blue {
+ label = "soc:blue:broadband";
+ gpios = <&gpio 8 1>;
+ };
+
+ wireless-red {
+ label = "soc:red:wireless";
+ gpios = <&gpio 9 1>;
+ };
+ wireless-green {
+ label = "soc:green:wireless";
+ gpios = <&gpio 10 1>;
+ };
+ wireless-blue {
+ label = "soc:blue:wireless";
+ gpios = <&gpio 11 1>;
+ };
+
+ power-red {
+ label = "soc:red:power";
+ gpios = <&gpio 12 1>;
+ };
+ power-green {
+ label = "soc:green:power";
+ gpios = <&gpio 14 1>;
+ };
+ power-blue {
+ label = "soc:blue:power";
+ gpios = <&gpio 15 1>;
+ };
+
+ dimmed {
+ label = "dimmed";
+ gpios = <&gpio 19 0>;
+ };
+ };
+};
diff --git a/target/linux/lantiq/image/Makefile b/target/linux/lantiq/image/Makefile
index 3e8c20b..726092d 100644
--- a/target/linux/lantiq/image/Makefile
+++ b/target/linux/lantiq/image/Makefile
@@ -414,6 +414,9 @@ Image/Build/Profile/P2812HNUF3=$(call Image/BuildNAND/$(1),$(1),P2812HNUF3)
Image/BuildKernel/Profile/ARV7519RW22=$(call Image/BuildKernel/Template,ARV7519RW22,$(1))
Image/Build/Profile/ARV7519RW22=$(call Image/Build/$(1),$(1),ARV7519RW22)
+Image/BuildKernel/Profile/BTHOMEHUBV5A=$(call Image/BuildKernel/Template,BTHOMEHUBV5A)
+Image/Build/Profile/BTHOMEHUBV5A=$(call Image/BuildNAND/$(1),$(1),BTHOMEHUBV5A)
+
Image/BuildKernel/Profile/EASY80920NAND=$(call Image/BuildKernel/Template,EASY80920NAND)
Image/Build/Profile/EASY80920NAND=$(call Image/Build/$(1),$(1),EASY80920NAND)
diff --git a/target/linux/lantiq/xrx200/profiles/bt.mk b/target/linux/lantiq/xrx200/profiles/bt.mk
new file mode 100644
index 0000000..a1083bb
--- /dev/null
+++ b/target/linux/lantiq/xrx200/profiles/bt.mk
@@ -0,0 +1,9 @@
+define Profile/BTHOMEHUBV5A
+ NAME:=BT Home Hub 5A
+ PACKAGES:=kmod-ath9k kmod-ath10k wpad-mini kmod-usb-dwc2
+endef
+
+BTHOMEHUBV5A_UBIFS_OPTS:="-m 2048 -e 126KiB -c 4096"
+BTHOMEHUBV5A_UBI_OPTS:="-m 2048 -p 128KiB -s 512"
+
+$(eval $(call Profile,BTHOMEHUBV5A))
--
2.4.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list