[FS#4039] MR8300 / Device is not active - Qualcomm Atheros QCA9886 802.11nac

[OpenWrt Bugs]

THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.

A new Flyspray task has been opened.  Details are below. 

User who did this - lejeczek (lejeczek) 

Attached to Project - OpenWrt/LEDE Project
Summary - MR8300 / Device is not active - Qualcomm Atheros QCA9886 802.11nac
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To - 
Operating System - All
Severity - Low
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - Hi.
A novice here so please go easy on me.
I've just got OpenWrt 21.02.0 r16279-5cc0535800 on my Linksys MR8300 and one iface does not seem to work.
I followed some suggestion people share on forum, where setup of wifi+timezone+timesync is supposed to be done prior to flash to OpenWrt but that changed nothing.
Even if wlan0 is the only wifi iface/network enabled it fails to start.

----
Tue Sep 14 10:33:15 2021 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY
Tue Sep 14 10:33:15 2021 daemon.info procd: - init complete -
Tue Sep 14 10:33:16 2021 daemon.err odhcpd[1028]: Failed to send to ff02::1%lan at br-lan (Address not available)
Tue Sep 14 10:33:17 2021 kern.warn kernel: [   27.923131] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
Tue Sep 14 10:33:17 2021 kern.warn kernel: [   27.923177] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
Tue Sep 14 10:33:17 2021 kern.info kernel: [   27.977890] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
Tue Sep 14 10:33:17 2021 kern.info kernel: [   27.979711] ath10k_pci 0000:01:00.0: wmi print 'free: 114572 iram: 12644 sram: 29508'
Tue Sep 14 10:33:18 2021 kern.info kernel: [   28.311499] ath10k_pci 0000:01:00.0: rts threshold -1
Tue Sep 14 10:33:18 2021 kern.warn kernel: [   28.313728] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
Tue Sep 14 10:33:18 2021 kern.info kernel: [   28.326258] br-lan: port 2(wlan0) entered blocking state
Tue Sep 14 10:33:18 2021 kern.info kernel: [   28.326583] br-lan: port 2(wlan0) entered disabled state
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: Frequency 5500 (primary) not allowed for AP mode, flags: 0x301979 RADAR
Tue Sep 14 10:33:18 2021 daemon.err hostapd: Primary frequency not allowed
Tue Sep 14 10:33:18 2021 daemon.warn hostapd: wlan0: IEEE 802.11 Configured channel (100) or frequency (5500) not found from the channel list of the current mode (2) IEEE 802.11a
Tue Sep 14 10:33:18 2021 daemon.warn hostapd: wlan0: IEEE 802.11 Hardware does not support configured channel
Tue Sep 14 10:33:18 2021 daemon.err hostapd: Could not select hw_mode and channel. (-3)
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->DISABLED
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: AP-DISABLED
Tue Sep 14 10:33:18 2021 daemon.err hostapd: wlan0: Unable to setup interface.
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Tue Sep 14 10:33:18 2021 kern.info kernel: [   28.332587] device wlan0 entered promiscuous mode
Tue Sep 14 10:33:18 2021 kern.info kernel: [   28.412245] device wlan0 left promiscuous mode
Tue Sep 14 10:33:18 2021 kern.info kernel: [   28.413594] br-lan: port 2(wlan0) entered disabled state
Tue Sep 14 10:33:18 2021 kern.warn kernel: [   28.479885] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 0
Tue Sep 14 10:33:18 2021 daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
Tue Sep 14 10:33:18 2021 daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
Tue Sep 14 10:33:18 2021 daemon.notice netifd: radio0 (1354): Command failed: Invalid argument
Tue Sep 14 10:33:18 2021 daemon.notice netifd: radio0 (1354): Device setup failed: HOSTAPD_START_FAILED
----

Please feel free to ask for any info you might need, I'll try to get it.

Many thanks, L.

More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=4039

You are receiving this message because you have requested it from the Flyspray bugtracking system.  If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.