[PATCH] mediatek: filogic: add Acelink EW-7886CAX support
Daniel Golle
daniel at makrotopia.org
Mon Nov 20 03:18:14 PST 2023
Hi Rafal,
looks good in general, please see minor comments in line.
On Mon, Nov 20, 2023 at 12:01:38PM +0100, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal at milecki.pl>
>
> Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
> It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
> on-SoC Wi-Fi.
>
> My unit came with Mediatek's firmware (based on OpenWrt 21.02)
> installed. It was possible to simply upgrade using OpenWrt's sysupgrade
> tool.
>
> Another verified upgrade method is using U-Boot (requires UART). During
> every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
> firmware" allows using U-Boot's tftp client to load and flash factory
> image.
>
> Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
> ---
> .../dts/mt7986a-acelink-ew-7886cax.dts | 236 ++++++++++++++++++
> target/linux/mediatek/image/filogic.mk | 17 ++
> 2 files changed, 253 insertions(+)
> create mode 100644 target/linux/mediatek/dts/mt7986a-acelink-ew-7886cax.dts
>
> diff --git a/target/linux/mediatek/dts/mt7986a-acelink-ew-7886cax.dts b/target/linux/mediatek/dts/mt7986a-acelink-ew-7886cax.dts
> new file mode 100644
> index 0000000000..bdbcf1f364
> --- /dev/null
> +++ b/target/linux/mediatek/dts/mt7986a-acelink-ew-7886cax.dts
> @@ -0,0 +1,236 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +#include "mt7986a.dtsi"
> +
> +/ {
> + model = "Acelink EW-7886CAX";
> + compatible = "acelink,ew-7886cax", "mediatek,mt7986a";
> +
> + aliases {
> + serial0 = &uart0;
> + led-boot = &led_status_blue;
> + led-running = &led_status_green;
> + led-upgrade = &led_status_red;
> + led-failsafe = &led_status_red;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory at 40000000 {
> + reg = <0 0x40000000 0 0x20000000>;
> + device_type = "memory";
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + key-restart {
> + label = "Reset";
> + gpios = <&pio 7 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_status_red: led-0 {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_RED>;
> + gpios = <&pio 18 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led_status_green: led-1 {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&pio 19 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led_status_blue: led-2 {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_BLUE>;
> + gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +};
> +
> +&watchdog {
> + status = "okay";
> +};
> +
> +&pio {
> + spi_flash_pins: spi-flash-pins-33-to-38 {
> + mux {
> + function = "spi";
> + groups = "spi0", "spi0_wp_hold";
> + };
> + conf-pu {
> + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
> + drive-strength = <8>;
> + mediatek,pull-up-adv = <0>; /* bias-disable */
> + };
> + conf-pd {
> + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
> + drive-strength = <8>;
> + mediatek,pull-down-adv = <0>; /* bias-disable */
> + };
> + };
> +
> + wf_2g_5g_pins: wf_2g_5g-pins {
> + mux {
> + function = "wifi";
> + groups = "wf_2g", "wf_5g";
> + };
> + conf {
> + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> + "WF1_TOP_CLK", "WF1_TOP_DATA";
> + drive-strength = <4>;
> + };
> + };
> +
> + wf_dbdc_pins: wf-dbdc-pins {
> + mux {
> + function = "wifi";
> + groups = "wf_dbdc";
> + };
> + conf {
> + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> + "WF1_TOP_CLK", "WF1_TOP_DATA";
> + drive-strength = <4>;
> + };
> + };
> +};
> +
> +&trng {
> + status = "okay";
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_flash_pins>;
> + status = "okay";
> +
> + flash at 0 {
> + compatible = "spi-nand";
> + reg = <0>;
> + spi-max-frequency = <52000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
Did you check whether the stock bootloader is using MediaTek's NMBM bad
block relocation mechanism?
If so, you should enable it in Linux as well.
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partitions: partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "bootloader";
> + reg = <0x0 0x100000>;
> + read-only;
> + };
> +
> + partition at 100000 {
> + label = "u-boot-env";
> + reg = <0x100000 0x80000>;
> + };
> +
> + factory: partition at 180000 {
> + label = "factory";
> + reg = <0x180000 0x200000>;
> + read-only;
> + compatible = "nvmem-cells";
> +
> + nvmem-layout {
> + compatible = "fixed-layout";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + eeprom: eeprom at 0 {
> + reg = <0x0 0x1000>;
> + };
> +
> + macaddr: macaddr at 4 {
> + reg = <0x4 0x6>;
> + };
> + };
> + };
> +
> + partition at 380000 {
> + label = "fip";
> + reg = <0x380000 0x200000>;
> + };
> +
> + partition at 580000 {
> + label = "ubi";
> + reg = <0x580000 0x4000000>;
> + };
> + };
> + };
> +};
> +
> +&pcie_phy {
> + status = "okay";
> +};
> +
> +ð {
> + status = "okay";
> +
> + mac at 1 {
> + compatible = "mediatek,eth-mac";
> + reg = <1>;
> + phy-mode = "2500base-x";
> + phy-handle = <&phy6>;
> + nvmem-cells = <&macaddr>;
> + nvmem-cell-names = "mac-address";
Is this the MAC address also printed on the device label?
If so, please reference it as label-mac-device in aliases.
> + };
> +
> + mdio-bus {
> + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
> + reset-delay-us = <50000>;
> + reset-post-delay-us = <20000>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy6: phy at 6 {
Maybe add comment here about which kind of PHY that is (MaxLinear? RealTek? Aquantia?).
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <6>;
> + };
> + };
> +};
> +
> +&wifi {
> + status = "okay";
> + pinctrl-names = "default", "dbdc";
> + pinctrl-0 = <&wf_2g_5g_pins>;
> + pinctrl-1 = <&wf_dbdc_pins>;
> + nvmem-cells = <&eeprom>;
> + nvmem-cell-names = "eeprom";
> +};
> diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
> index 4d4f3b62a2..c04c952bc5 100644
> --- a/target/linux/mediatek/image/filogic.mk
> +++ b/target/linux/mediatek/image/filogic.mk
> @@ -105,6 +105,23 @@ define Build/cetron-header
> rm $@.tmp
> endef
>
> +define Device/acelink_ew-7886cax
> + DEVICE_VENDOR := Acelink
> + DEVICE_MODEL := EW-7886CAX
> + DEVICE_DTS := mt7986a-acelink-ew-7886cax
> + DEVICE_DTS_DIR := ../dts
> + DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
> + UBINIZE_OPTS := -E 5
> + BLOCKSIZE := 128k
> + PAGESIZE := 2048
> + IMAGE_SIZE := 65536k
> + KERNEL_IN_UBI := 1
> + IMAGES += factory.bin
> + IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
> + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
> +endef
> +TARGET_DEVICES += acelink_ew-7886cax
> +
> define Device/asus_tuf-ax4200
> DEVICE_VENDOR := ASUS
> DEVICE_MODEL := TUF-AX4200
> --
> 2.35.3
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list