[PATCH 21.02 07/11] ramips: add support for JCG Q20

Petr Štetiar ynezz at true.cz
Tue Jun 8 02:45:08 PDT 2021


From: Chukun Pan <amadeus at jmu.edu.cn>

JCG Q20 is an AX 1800M router.

Hardware specs:
  SoC: MediaTek MT7621AT
  Flash: Winbond W29N01HV 128 MiB
  RAM: Winbond W632GU6NB-11 256 MiB
  WiFi: MT7915 2.4/5 GHz 2T2R
  Ethernet: 10/100/1000 Mbps x3
  LED: Status (red / blue)
  Button: Reset, WPS
  Power: DC 12V,1A

Flash instructions:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings.

MAC addresses map:
  0x00004 *:3e wlan2g/wlan5g
  0x3fff4 *:3c lan/label
  0x3fffa *:3c wan

Signed-off-by: Chukun Pan <amadeus at jmu.edu.cn>
(cherry picked from commit 57cb387cfeee2a07902a2f1383ca471ef47265f3)
---
 package/boot/uboot-envtools/files/ramips      |   3 +
 target/linux/ramips/dts/mt7621_jcg_q20.dts    | 175 ++++++++++++++++++
 target/linux/ramips/image/mt7621.mk           |  17 ++
 .../mt7621/base-files/etc/board.d/02_network  |   1 +
 .../etc/hotplug.d/ieee80211/10_fix_wifi_mac   |   4 +
 .../mt7621/base-files/lib/upgrade/platform.sh |   1 +
 6 files changed, 201 insertions(+)
 create mode 100644 target/linux/ramips/dts/mt7621_jcg_q20.dts

diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips
index c153b6a4226b..5800a548e3e4 100644
--- a/package/boot/uboot-envtools/files/ramips
+++ b/package/boot/uboot-envtools/files/ramips
@@ -44,6 +44,9 @@ ravpower,rp-wd03)
 	[ -n "$idx" ] && \
 		ubootenv_add_uci_config "/dev/mtd$idx" "0x4000" "0x1000" "0x1000"
 	;;
+jcg,q20)
+	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
+	;;
 linksys,ea7300-v1|\
 linksys,ea7300-v2|\
 linksys,ea7500-v2|\
diff --git a/target/linux/ramips/dts/mt7621_jcg_q20.dts b/target/linux/ramips/dts/mt7621_jcg_q20.dts
new file mode 100644
index 000000000000..f0e829393ce1
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_jcg_q20.dts
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "jcg,q20", "mediatek,mt7621-soc";
+	model = "JCG Q20";
+
+	aliases {
+		led-boot = &led_status_red;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_blue;
+		led-upgrade = &led_status_blue;
+		label-mac-device = &gmac0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: status_red {
+			label = "red:status";
+			gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_status_blue: status_blue {
+			label = "blue:status";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	ubi-concat {
+		compatible = "mtd-concat";
+		devices = <&ubiconcat0 &ubiconcat1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "ubi";
+				reg = <0x0 0x5900000>;
+			};
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition at 0 {
+			label = "Bootloader";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition at 80000 {
+			label = "Config";
+			reg = <0x80000 0x80000>;
+		};
+
+		factory: partition at 100000 {
+			label = "Factory";
+			reg = <0x100000 0x80000>;
+			read-only;
+		};
+
+		partition at 180000 {
+			label = "kernel";
+			reg = <0x180000 0x400000>;
+		};
+
+		ubiconcat0: partition at 580000 {
+			label = "ubiconcat0";
+			reg = <0x580000 0x1c00000>;
+		};
+
+		partition at 2180000 {
+			label = "firmware_backup";
+			reg = <0x2180000 0x2000000>;
+		};
+
+		partition at 4180000 {
+			label = "rootfs_data_back";
+			reg = <0x4180000 0x80000>;
+			read-only;
+		};
+
+		partition at 4200000 {
+			label = "nvram_config";
+			reg = <0x4200000 0x80000>;
+			read-only;
+		};
+
+		ubiconcat1: partition at 4280000 {
+			label = "ubiconcat1";
+			reg = <0x4280000 0x3d00000>;
+		};
+
+		/*
+		 * last 512 KiB are for the bad block table
+		 */
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie1 {
+	wifi at 0,0 {
+		compatible = "mediatek,mt76";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x0>;
+	};
+};
+
+&gmac0 {
+	mtd-mac-address = <&factory 0x3fff4>;
+};
+
+&switch0 {
+	ports {
+		port at 0 {
+			status = "okay";
+			label = "wan";
+			mtd-mac-address = <&factory 0x3fffa>;
+		};
+
+		port at 1 {
+			status = "okay";
+			label = "lan1";
+		};
+
+		port at 4 {
+			status = "okay";
+			label = "lan2";
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "jtag", "wdt";
+		function = "gpio";
+	};
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 0ec283d74fb2..6edf6c0cd6a7 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -720,6 +720,23 @@ define Device/jcg_jhr-ac876m
 endef
 TARGET_DEVICES += jcg_jhr-ac876m
 
+define Device/jcg_q20
+  $(Device/dsa-migration)
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  UBINIZE_OPTS := -E 5
+  KERNEL_SIZE := 4096k
+  IMAGE_SIZE := 91136k
+  IMAGES += factory.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
+	check-size
+  DEVICE_VENDOR := JCG
+  DEVICE_MODEL := Q20
+  DEVICE_PACKAGES := kmod-mt7915e uboot-envtools
+endef
+TARGET_DEVICES += jcg_q20
+
 define Device/jcg_y2
   $(Device/dsa-migration)
   $(Device/uimage-lzma-loader)
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index f017e4782e0e..f5b075f1f4a8 100755
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -15,6 +15,7 @@ ramips_setup_interfaces()
 		;;
 	asiarf,ap7621-nv1|\
 	glinet,gl-mt1300|\
+	jcg,q20|\
 	lenovo,newifi-d1|\
 	mikrotik,routerboard-m33g|\
 	xiaomi,mi-router-3g|\
diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
index e7f778aaf88a..427bde4e38f7 100644
--- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
+++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
@@ -14,6 +14,10 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && \
 			macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress
 		;;
+	jcg,q20)
+		[ "$PHYNBR" = "1" ] && \
+			macaddr_setbit_la "$(mtd_get_mac_binary Factory 0x4)" > /sys${DEVPATH}/macaddress
+		;;
 	linksys,ea7300-v1|\
 	linksys,ea7300-v2|\
 	linksys,ea7500-v2)
diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
index d30bc3db2edd..98e429fdbf42 100755
--- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
@@ -49,6 +49,7 @@ platform_do_upgrade() {
 	dlink,dir-2640-a1|\
 	dlink,dir-2660-a1|\
 	hiwifi,hc5962|\
+	jcg,q20|\
 	linksys,ea7300-v1|\
 	linksys,ea7300-v2|\
 	linksys,ea7500-v2|\



More information about the openwrt-devel mailing list