[PATCH v5 2/2] realtek: add support for ZyXEL GS1900-8HP v1 and v2

Stijn Segers foss at volatilesystems.org
Fri Jan 8 08:32:48 EST 2021


The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.

The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.

Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].

After careful consideration it was decided to go with separate images
for each version.

Specifications (v1)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART:      1 serial header with populated standard pin connector on the
             left side of the PCB, towards the bottom. Pins are labeled:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Specifications (v2)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART:      1 angled serial header with populated standard pin connector
             accessible from outside through the ventilation slits on the
             side. Pins from top to bottom are clearly marked on the PCB:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  # rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  # setsys bootpartition 0
  # savesys
* Download the image onto the device and boot from it:
  # tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
  # bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  # sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin

Signed-off-by: Stijn Segers <foss at volatilesystems.org>
---
 .../realtek/base-files/etc/board.d/02_network |  6 +++++
 .../dts/rtl8380_zyxel_gs1900-8hp-v1.dts       |  8 +++++++
 .../dts/rtl8380_zyxel_gs1900-8hp-v2.dts       |  8 +++++++
 target/linux/realtek/image/Makefile           | 24 ++++++++++++++++++-
 4 files changed, 45 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v1.dts
 create mode 100644 target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v2.dts

diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index 84fefa536d..cc8beb1c95 100755
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -52,6 +52,12 @@ case $board in
 netgear,gs110tpp-v1)
 	ucidef_set_poe 130 "$lan_list"
 	;;
+zyxel,gs1900-8hp-v1)
+	ucidef_set_poe 70 "$lan_list"
+	;;
+zyxel,gs1900-8hp-v2)
+	ucidef_set_poe 70 "$lan_list"
+	;;
 zyxel,gs1900-10hp)
 	ucidef_set_poe 77 "$lan_list"
 	;;
diff --git a/target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v1.dts b/target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v1.dts
new file mode 100644
index 0000000000..0d9b7c97c0
--- /dev/null
+++ b/target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v1.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "rtl8380_zyxel_gs1900.dtsi"
+
+/ {
+	compatible = "zyxel,gs1900-8hp-v1", "realtek,rtl838x-soc";
+	model = "ZyXEL GS1900-8HP v1 Switch";
+};
diff --git a/target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v2.dts b/target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v2.dts
new file mode 100644
index 0000000000..cdc4aed6d1
--- /dev/null
+++ b/target/linux/realtek/dts/rtl8380_zyxel_gs1900-8hp-v2.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "rtl8380_zyxel_gs1900.dtsi"
+
+/ {
+	compatible = "zyxel,gs1900-8hp-v2", "realtek,rtl838x-soc";
+	model = "ZyXEL GS1900-8HP v2 Switch";
+};
diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile
index 765e516a0a..39b28b6c67 100644
--- a/target/linux/realtek/image/Makefile
+++ b/target/linux/realtek/image/Makefile
@@ -65,11 +65,33 @@ define Device/netgear_gs110tpp-v1
 endef
 TARGET_DEVICES += netgear_gs110tpp-v1
 
-define Device/zyxel_gs1900-10hp
+define Device/zyxel_gs1900
   SOC := rtl8380
   IMAGE_SIZE := 6976k
   DEVICE_VENDOR := ZyXEL
+endef
+
+define Device/zyxel_gs1900-8hp-v1
+  $(Device/zyxel_gs1900)
+  DEVICE_MODEL := GS1900-8HP
+  DEVICE_PACKAGES += lua-rs232
+  DEVICE_VARIANT := v1
+endef
+TARGET_DEVICES += zyxel_gs1900-8hp-v1
+
+define Device/zyxel_gs1900-8hp-v2
+  $(Device/zyxel_gs1900)
+  DEVICE_MODEL := GS1900-8HP
+  DEVICE_PACKAGES += lua-rs232
+  DEVICE_VARIANT := v2
+endef
+TARGET_DEVICES += zyxel_gs1900-8hp-v2
+
+
+define Device/zyxel_gs1900-10hp
+  $(Device/zyxel_gs1900)
   DEVICE_MODEL := GS1900-10HP
+  DEVICE_PACKAGES += lua-rs232
 endef
 TARGET_DEVICES += zyxel_gs1900-10hp
 
-- 
2.20.1




More information about the openwrt-devel mailing list