[PATCH] ramips: mt7621: add TP-Link EAP235-Wall support

Sander Vanheule sander at svanheule.net
Sun Feb 14 05:03:22 EST 2021


The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.

When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.

The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.

Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
  * Back side: ETH0, PoE PD port
  * Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)

Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).

Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
>From OEM ifconfig:
    eth     a4:2b:b0:...:88
    ra0     a4:2b:b0:...:88
    rai0    a4:2b:b0:...:89

Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface

Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
  pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
  bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
    # tftpboot 84000000 openwrt-initramfs.bin
    # bootm

Hardware was kindly provided for porting by Stijn Segers.

Tested-by: Stijn Segers <foss at volatilesystems.org>
Signed-off-by: Sander Vanheule <sander at svanheule.net>
---
Known issues with this device:
The MT7613BE radio is currently not well supported by the mt7615 driver:
- The EEPROM blob is not recognized, so (Tx) power levels aren't useful.
  Patch sent to linux-wireless:
  https://lore.kernel.org/linux-wireless/20210202085953.9564-1-sander@svanheule.net/
- DFS support is incomplete (known issue for MT7613)
- Radio stops responding after a while when idling, reboot required to
  bring it to life. Reported by Stijn, appears to be introduced by
  2021-01-27 bump of mt76.

  kern.err kernel: [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout

 .../dts/mt7621_tplink_eap235-wall-v1.dts      | 172 ++++++++++++++++++
 target/linux/ramips/image/mt7621.mk           |  12 ++
 .../mt7621/base-files/etc/board.d/02_network  |   3 +
 tools/firmware-utils/src/tplink-safeloader.c  |  29 +++
 4 files changed, 216 insertions(+)
 create mode 100644 target/linux/ramips/dts/mt7621_tplink_eap235-wall-v1.dts

diff --git a/target/linux/ramips/dts/mt7621_tplink_eap235-wall-v1.dts b/target/linux/ramips/dts/mt7621_tplink_eap235-wall-v1.dts
new file mode 100644
index 0000000000..d63623dcbd
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_tplink_eap235-wall-v1.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "tplink,eap235-wall-v1", "mediatek,mt7621-soc";
+	model = "TP-LINK EAP235-Wall v1";
+
+	aliases {
+		label-mac-device = &gmac0;
+		led-boot = &led_status;
+		led-failsafe = &led_status;
+		led-running = &led_status;
+		led-upgrade = &led_status;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status: status {
+			label = "white:status";
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		led {
+			label = "led";
+			gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	gpio-export {
+		compatible = "gpio-export";
+
+		poe_passthrough {
+			gpio-export,name = "tp-link:poe-passthrough:enable";
+			gpio-export,output = <0>;
+			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x00000 0x80000>;
+				read-only;
+			};
+
+			partition at 80000 {
+				label = "partition-table";
+				reg = <0x80000 0x10000>;
+				read-only;
+			};
+
+			info: partition at 90000 {
+				label = "product-info";
+				reg = <0x90000 0x10000>;
+				read-only;
+			};
+
+			partition at a0000 {
+				compatible = "tplink,firmware";
+				label = "firmware";
+				reg = <0x0a0000 0xd20000>;
+			};
+
+			partition at dc0000 {
+				label = "user-config";
+				reg = <0xdc0000 0x030000>;
+				read-only;
+			};
+
+			/* 0xdf0000 - 0xf30000 unused  */
+
+			partition at f30000 {
+				label = "mutil-log";
+				reg = <0xf30000 0x080000>;
+				read-only;
+			};
+
+			partition at fb0000 {
+				label = "oops";
+				reg = <0xfb0000 0x040000>;
+				read-only;
+			};
+
+			radio: partition at ff0000 {
+				label = "radio";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie0 {
+	mt76 at 0,0 {
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&radio 0x0>;
+		mtd-mac-address = <&info 0x8>;
+	};
+};
+
+&pcie1 {
+	mt76 at 0,0 {
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&radio 0x8000>;
+		ieee80211-freq-limit = <5000000 6000000>;
+		mtd-mac-address = <&info 0x8>;
+		mtd-mac-address-increment = <1>;
+	};
+};
+
+&gmac0 {
+	mtd-mac-address = <&info 0x8>;
+};
+
+&switch0 {
+	ports {
+		port at 0 {
+			status = "okay";
+			label = "lan0";
+		};
+
+		port at 1 {
+			status = "okay";
+			label = "lan3";
+		};
+
+		port at 2 {
+			status = "okay";
+			label = "lan2";
+		};
+
+		port at 3 {
+			status = "okay";
+			label = "lan1";
+		};
+	};
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 203ca1b908..6efda9eb90 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -1114,6 +1114,18 @@ define Device/totolink_x5000r
 endef
 TARGET_DEVICES += totolink_x5000r
 
+define Device/tplink_eap235-wall-v1
+  $(Device/tplink-safeloader)
+  DEVICE_MODEL := EAP235-WALL
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
+  TPLINK_BOARD_ID := EAP235-WALL-V1
+  IMAGE_SIZE := 13440k
+  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
+	pad-extra 128
+endef
+TARGET_DEVICES += tplink_eap235-wall-v1
+
 define Device/tplink_re350-v1
   $(Device/dsa-migration)
   $(Device/tplink-safeloader)
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index 46cb65ffbe..89e679be7c 100755
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -55,6 +55,9 @@ ramips_setup_interfaces()
 	mikrotik,routerboard-760igs)
 		ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan sfp"
 		;;
+	tplink,eap235-wall-v1)
+		ucidef_set_interface_lan "lan0 lan1 lan2 lan3"
+		;;
 	ubnt,edgerouter-x)
 		ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4" "eth0"
 		;;
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index b9dfad51a6..da73e1bf30 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -1447,6 +1447,35 @@ static struct device_info boards[] = {
 		.last_sysupgrade_partition = "file-system"
 	},
 
+	/** Firmware layout for the EAP235-Wall v1 */
+	{
+		.id     = "EAP235-WALL-V1",
+		.support_list =
+			"SupportList:\r\n"
+			"EAP235-Wall(TP-Link|UN|AC1200-D):1.0\r\n",
+		.part_trail = PART_TRAIL_NONE,
+		.soft_ver = NULL,
+		.soft_ver_compat_level = 1,
+
+		.partitions = {
+			{"fs-uboot", 0x00000, 0x80000},
+			{"partition-table", 0x80000, 0x02000},
+			{"default-mac", 0x90000, 0x01000},
+			{"support-list", 0x91000, 0x00100},
+			{"product-info", 0x91100, 0x00400},
+			{"soft-version", 0x92000, 0x00100},
+			{"firmware", 0xa0000, 0xd20000},
+			{"user-config", 0xdc0000, 0x30000},
+			{"mutil-log", 0xf30000, 0x80000},
+			{"oops", 0xfb0000, 0x40000},
+			{"radio", 0xff0000, 0x10000},
+			{NULL, 0, 0}
+		},
+
+		.first_sysupgrade_partition = "os-image",
+		.last_sysupgrade_partition = "file-system"
+	},
+
 	/** Firmware layout for the EAP245 v1 */
 	{
 		.id     = "EAP245-V1",
-- 
2.29.2




More information about the openwrt-devel mailing list