[PATCH] ramips: add support for Wavlink WL-WN578A2
Adrian Schmutzler
mail at adrianschmutzler.de
Sun Apr 25 21:27:59 BST 2021
Hi,
comments inline. Nothing really serious ...
> -----Original Message-----
> From: openwrt-devel [mailto:openwrt-devel-bounces at lists.openwrt.org]
> On Behalf Of dev.aldrian at gmail.com
> Sent: Donnerstag, 22. April 2021 21:24
> To: openwrt-devel at lists.openwrt.org
> Cc: Thomas Aldrian <dev.aldrian at gmail.com>
> Subject: [PATCH] ramips: add support for Wavlink WL-WN578A2
>
> From: Thomas Aldrian <dev.aldrian at gmail.com>
>
> This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
> wireless router. This device is also sold under the name SilverCrest SWV 733
> A2.
>
> Device Specifications:
>
> - CPU: MediaTek MT7628AN (580MHz)
> - Flash: 8MB
> - RAM: 64MB
> - Bootloader: U-Boot
> - Ethernet: 2x 10/100 Mbps
> - 2.4 GHz: 802.11b/g/n SoC
> - 5 GHz: 802.11a/n/ac MT7610E
> - Antennas: internal
> - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
> - Buttons: Reset, WPS
> - Sliding mode switch: AP, repeater, client
> - Small sliding power switch
>
> Flashing instructions:
>
> U-Boot launches TFTP client if WPS button is pressed during power-on.
> Configure as follows:
>
> - Server IP: 192.168.10.100
> - Filename (rename sysupgrade file to this): firmware.bin
>
> Flashing should not take more than a minute, device will reboot
> automatically.
>
> Signed-off-by: Thomas Aldrian <dev.aldrian at gmail.com>
> ---
> .../dts/mt7628an_wavlink_wl-wn578a2.dts | 165 ++++++++++++++++++
> target/linux/ramips/image/mt76x8.mk | 10 ++
> .../mt76x8/base-files/etc/board.d/01_leds | 8 +
> .../mt76x8/base-files/etc/board.d/02_network | 6 +-
> 4 files changed, 187 insertions(+), 2 deletions(-) create mode 100644
> target/linux/ramips/dts/mt7628an_wavlink_wl-wn578a2.dts
>
> diff --git a/target/linux/ramips/dts/mt7628an_wavlink_wl-wn578a2.dts
> b/target/linux/ramips/dts/mt7628an_wavlink_wl-wn578a2.dts
> new file mode 100644
> index 0000000000..69a54c297b
> --- /dev/null
> +++ b/target/linux/ramips/dts/mt7628an_wavlink_wl-wn578a2.dts
> @@ -0,0 +1,165 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +#include "mt7628an.dtsi"
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + compatible = "wavlink,wl-wn578a2", "mediatek,mt7628an-soc";
> + model = "Wavlink WL-WN578A2";
> +
> + aliases {
> + led-boot = &led_wps;
> + led-failsafe = &led_wps;
> + led-running = &led_wps;
> + led-upgrade = &led_wps;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WPS_BUTTON>;
> + };
> +
> + ap {
> + label = "ap";
> + gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
> + linux,code = <BTN_0>;
> + linux,input-type = <EV_SW>;
> + };
> +
> + repeater {
> + label = "repeater";
> + gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
> + linux,code = <BTN_1>;
> + linux,input-type = <EV_SW>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + wifi-high {
> + label = "green:wifi-high";
> + gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
> + };
> +
> + wifi-med {
> + label = "green:wifi-med";
> + gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + wifi-low {
> + label = "green:wifi-low";
> + gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
> + };
> +
> + lan {
> + label = "green:lan";
> + gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
> + };
> +
> + wan {
> + label = "green:wan";
> + gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_wps: wps {
> + label = "green:wps";
> + gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&state_default {
> + gpio {
> + groups = "i2c", "wdt", "wled_an", "p0led_an", "p1led_an",
> "p2_led", "p3led_an", "p4led_an", "refclk";
> + function = "gpio";
> + };
p2led_an (typo)
Apart from that, gpio 11 is missing ...
And please wrap this long line.
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&pcie0 {
> + mt76 at 0,0 {
wifi at 0,0
> + reg = <0x0000 0 0 0 0>;
> + mediatek,mtd-eeprom = <&factory 0x8000>;
> + ieee80211-freq-limit = <5000000 6000000>;
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <40000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x50000 0x7b0000>;
> + };
> + };
> + };
> +};
> +
> +&wmac {
> + status = "okay";
> +};
> +
> +ðernet {
> + mtd-mac-address = <&factory 0x28>;
> +};
> +
> +&esw {
> + mediatek,portmap = <0x2f>;
> +};
> +
> +&usbphy {
> + status = "disabled";
> +};
> +
> +&ehci {
> + status = "disabled";
> +};
> +
> +&ohci {
> + status = "disabled";
> +};
> diff --git a/target/linux/ramips/image/mt76x8.mk
> b/target/linux/ramips/image/mt76x8.mk
> index d5a9684dba..79221239e9 100644
> --- a/target/linux/ramips/image/mt76x8.mk
> +++ b/target/linux/ramips/image/mt76x8.mk
> @@ -733,6 +733,16 @@ define Device/wavlink_wl-wn577a2 endef
> TARGET_DEVICES += wavlink_wl-wn577a2
>
> +define Device/wavlink_wl-wn578a2
> + IMAGE_SIZE := 7872k
> + DEVICE_VENDOR := Wavlink
> + DEVICE_MODEL := WL-WN578A2
> + DEVICE_ALT0_VENDOR := SilverCrest
> + DEVICE_ALT0_MODEL := SWV 733 A2
> + DEVICE_PACKAGES := rssileds kmod-mt76x0e endef TARGET_DEVICES +=
> +wavlink_wl-wn578a2
> +
> define Device/widora_neo-16m
> IMAGE_SIZE := 16064k
> DEVICE_VENDOR := Widora
> diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
> b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
> index fdef158ea8..00093a7cd7 100644
> --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
> @@ -133,6 +133,14 @@ wavlink,wl-wn577a2)
> ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0x8"
> ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x10"
> ;;
> +wavlink,wl-wn578a2)
> + ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0x8"
> + ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x10"
> + ucidef_set_rssimon "wlan1" "200000" "1"
> + ucidef_set_led_rssi "wifi-low" "wifi-low" "green:wifi-low" "wlan1"
> "1" "49"
> + ucidef_set_led_rssi "wifi-med" "wifi-med" "green:wifi-med" "wlan1"
> "50" "84"
> + ucidef_set_led_rssi "wifi-high" "wifi-high" "green:wifi-high" "wlan1"
> "85" "100"
> + ;;
Why wlan1? Is this chosen arbitrarily (than please drop the default setup), or is the vendor really also using only one specific radio for the RSSI leds?
Best
Adrian
> zbtlink,zbt-we1226)
> ucidef_set_led_netdev "wifi_led" "wifi" "green:wlan" "wlan0"
> ucidef_set_led_switch "lan1" "LAN1" "green:lan1" "switch0" "0x01"
> diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> index 5ce44d0e9b..d61a60591c 100644
> --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> @@ -46,7 +46,8 @@ ramips_setup_interfaces()
> ;;
> buffalo,wcr-1166ds|\
> elecom,wrc-1167fs|\
> - wavlink,wl-wn577a2)
> + wavlink,wl-wn577a2|\
> + wavlink,wl-wn578a2)
> ucidef_add_switch "switch0" \
> "3:lan" "4:wan" "6 at eth0"
> ;;
> @@ -168,7 +169,8 @@ ramips_setup_macs()
> ;;
> cudy,wr1000|\
> hilink,hlk-7688a|\
> - wavlink,wl-wn577a2)
> + wavlink,wl-wn577a2|\
> + wavlink,wl-wn578a2)
> wan_mac=$(mtd_get_mac_binary factory 0x2e)
> label_mac=$(mtd_get_mac_binary factory 0x4)
> ;;
> --
> 2.31.1
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: openpgp-digital-signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: not available
URL: <http://lists.openwrt.org/pipermail/openwrt-devel/attachments/20210425/93b9ffd5/attachment.sig>
More information about the openwrt-devel
mailing list