[OpenWrt-Devel] [PATCH v6] ramips: add support for Trendnet TEW-810DR
Heppler, J. Scott
shep971 at centurylink.net
Mon May 25 20:05:16 EDT 2020
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios both now functional
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid
-f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp.
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Signed-off-by: J. Scott Heppler <shep971 at centurylink.net>
Summary v4 -> v5
1. Enumerated installation steps and corrected grammar.
2. Added SPDX License Identifier to *.dts.
3. gpio-keys-polled -> gpio-keys in *.dts.
4. gpio2 0 is actually behind a Globe/Internet lens - changed to wan.
5. Increased spi-max-frequency 10000000 -> 50000000
6. jffs2 partition 0xe0000 -> 0xf0000.
7. &state_default groups dropped mdio, rgmii1, wled.
8. MAC assignments mirror DIR-810L and verify in Luci. Unchanged
02_network and *.dts.
9. 01_leds changed consistent with #4.
10. Removed SUPPORTED_DEVICES from image/mt7620.mk. Note: the D-Link
DIR-810L has the same SUPPORTED_DEVICES entry in image/mt7620.mk.
11. Builds/Runs on my test Device.
---
.../ramips/dts/mt7620a_trendnet_tew-810dr.dts | 166 ++++++++++++++++++
target/linux/ramips/image/mt7620.mk | 9 +
.../mt7620/base-files/etc/board.d/01_leds | 3 +
.../mt7620/base-files/etc/board.d/02_network | 8 +-
4 files changed, 183 insertions(+), 3 deletions(-)
create mode 100644 target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts
diff --git a/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts b/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts
new file mode 100644
index 0000000000..5012d39b51
--- /dev/null
+++ b/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts
@@ -0,0 +1,166 @@
+//SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "trendnet,tew-810dr", "ralink,mt7620a-soc";
+ model = "TRENDnet TEW-810DR";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_green;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ label-mac-device = ðernet;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_green: power_green {
+ label = "tew-810dr:green:power";
+ gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan_orange: wan_orange {
+ label = "tew-810dr:orange:wan";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan_green: wan_green {
+ label = "tew-810dr:green:wan";
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_orange {
+ label = "tew-810dr:orange:power";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ factory5g: partition at 50000 {
+ label = "factory5g";
+ reg = <0x50000 0x10000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "Wolf_Config";
+ reg = <0x60000 0x10000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ label = "MyDlink";
+ reg = <0x70000 0x80000>;
+ read-only;
+ };
+
+ partition at f0000 {
+ label = "Jffs2";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+
+ partition at 170000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x170000 0x690000>;
+ };
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "uartf", "ephy";
+ function = "gpio";
+ };
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x28>;
+ mediatek,portmap = "llllw";
+};
+
+&gsw {
+ mediatek,port4 = "ephy";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&wmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pa_pins>;
+
+ ralink,mtd-eeprom = <&factory 0x0>;
+ mtd-mac-address = <&factory 0x28>;
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ mtd-mac-address = <&factory 0x28>;
+ mtd-mac-address-increment = <2>;
+ };
+};
+
+&gpio2 {
+ status = "okay";
+};
diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index e435b1d15f..386809e40f 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -1005,6 +1005,15 @@ define Device/tplink_re210-v1
endef
TARGET_DEVICES += tplink_re210-v1
+define Device/trendnet_tew-810dr
+ SOC := mt7620a
+ DEVICE_PACKAGES := kmod-mt76x0e
+ DEVICE_VENDOR := TRENDnet
+ DEVICE_MODEL := TEW-810DR
+ IMAGE_SIZE := 6720k
+endef
+TARGET_DEVICES += trendnet_tew-810dr
+
define Device/vonets_var11n-300
SOC := mt7620n
IMAGE_SIZE := 3776k
diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
index c1deae59e3..595f84f5d2 100755
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
@@ -191,6 +191,9 @@ tplink,archer-mr200)
tplink,re200-v1)
ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" "eth0"
;;
+trendnet,tew-810dr)
+ ucidef_set_led_netdev "wan" "wan" "$boardname:green:wan" "eth0.2" "link tx rx"
+ ;;
youku,yk1)
set_wifi_led "$boardname:blue:air"
ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x10"
diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
index d024674c10..3fc0ce3049 100755
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
@@ -26,6 +26,7 @@ ramips_setup_interfaces()
ralink,mt7620a-mt7610e-evb|\
ralink,mt7620a-v22sg-evb|\
sanlinking,d240|\
+ trendnet,tew-810dr|\
youku,yk1|\
zbtlink,zbt-ape522ii|\
zbtlink,zbt-we826-16m|\
@@ -259,9 +260,10 @@ ramips_setup_macs()
alfa-network,ac1200rm|\
dlink,dir-810l|\
phicomm,psg1218a|\
- phicomm,psg1218b)
- wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x28)" 1)
- ;;
+ phicomm,psg1218b|\
+ trendnet,tew-810dr)
+ wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x28)" 1)
+ ;;
alfa-network,r36m-e4g|\
zbtlink,zbt-we1026-h-32m)
wan_mac=$(mtd_get_mac_binary factory 0x2e)
--
2.20.1
--
J. Scott Heppler
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list