[OpenWrt-Devel] [PATCH 2/2] bcm53xx: remove support for kernel 4.14

Adrian Schmutzler freifunk at adrianschmutzler.de
Mon May 25 06:19:52 EDT 2020


We currently support three kernel versions on this target, let's
just get rid of the oldest one.

Cc: Rafał Miłecki <rafal at milecki.pl>
Cc: John Crispin <john at phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
---
 target/linux/bcm53xx/config-4.14              | 363 --------------
 ...-Specify-USB-ports-for-USB-LED-of-Lu.patch |  30 --
 ...s-BCM5301X-Add-DT-for-Luxul-XBR-4500.patch |  96 ----
 ...s-BCM5301X-Add-DT-for-Luxul-ABR-4500.patch |  96 ----
 ...ts-BCM53573-Add-DT-for-Luxul-XAP-810.patch | 120 -----
 ...s-BCM53573-Add-DT-for-Luxul-XAP-1440.patch |  83 ----
 ...-add-missing-LEDs-for-Buffalo-WZR-90.patch |  96 ----
 ...-Switch-Luxul-XWC-1000-to-the-new-fi.patch |  39 --
 ...-Relicense-most-DTS-files-to-the-GPL.patch | 440 -----------------
 ...-Relicense-Buffalo-files-to-the-GPL-.patch |  79 ---
 ...CM5301X-Add-DT-for-Luxul-XWR-3150-V1.patch | 112 -----
 ...s-BCM5301X-Add-DT-for-Luxul-XAP-1610.patch |  90 ----
 ...-Relicense-Asus-RT-AC87U-file-to-the.patch |  48 --
 ...-Switch-D-Link-DIR-885L-to-the-new-p.patch |  39 --
 ...-Make-USB-3.0-PHY-use-MDIO-PHY-drive.patch | 456 ------------------
 ...M-dts-BCM53573-Add-architected-timer.patch |  34 --
 ...5301X-Add-support-for-Linksys-EA9500.patch | 269 -----------
 ...ts-BCM5301X-Specify-flash-partitions.patch | 167 -------
 ...-Relicense-BCM47081-BCM4709-files-to.patch |  58 ---
 ...-Relicense-BCM47094-file-to-the-GPL-.patch |  33 --
 ...-Relicense-Tenda-AC9-file-to-the-GPL.patch |  32 --
 ...-Relicense-SoC-file-to-the-GPL-2.0-M.patch |  33 --
 ...X-Add-basic-DT-for-Linksys-EA6500-V2.patch |  75 ---
 ...-Describe-Northstar-pins-mux-control.patch |  77 ---
 ...-Relicense-Luxul-files-to-the-GPL-2..patch |  41 --
 ...BCM5301X-Add-basic-DT-for-Phicomm-K3.patch | 107 ----
 ...pi-bcm53xx-simplify-reading-SPI-data.patch | 107 ----
 ...082-pinctrl-bcm-add-Northstar-driver.patch | 427 ----------------
 ...cm-ns-Use-uintptr_t-for-casting-data.patch |  38 --
 ...upport-updated-DT-binding-as-syscon-.patch |  99 ----
 ...s-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch |  80 ---
 ...support-for-performing-fake-doorbell.patch | 137 ------
 ...able-MMU-and-Dcache-during-decompres.patch | 101 ----
 ...01X-Update-Northstar-pinctrl-binding.patch |  31 --
 ...RM-BCM5301X-Add-DT-for-Netgear-R7900.patch |  64 ---
 ...power-button-for-Buffalo-WZR-1750DHP.patch |  20 -
 ...-BCM5301X-Add-serial-to-the-bootargs.patch | 116 -----
 ...-BCM5301X-Describe-partition-formats.patch |  25 -
 ...ct-JEDEC-incompatible-w25q128-using-.patch |  34 --
 ...-mark-and-erase-all-remaining-blocks.patch |  59 ---
 ...U-port-fixes-for-devices-not-using-p.patch |  52 --
 .../905-BCM53573-minor-hacks.patch            |  80 ---
 42 files changed, 4583 deletions(-)
 delete mode 100644 target/linux/bcm53xx/config-4.14
 delete mode 100644 target/linux/bcm53xx/patches-4.14/030-v4.15-0001-ARM-dts-BCM5301X-Specify-USB-ports-for-USB-LED-of-Lu.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/030-v4.15-0002-ARM-dts-BCM5301X-Add-DT-for-Luxul-XBR-4500.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/030-v4.15-0003-ARM-dts-BCM5301X-Add-DT-for-Luxul-ABR-4500.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/030-v4.15-0004-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-810.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/030-v4.15-0005-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-1440.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/031-v4.17-0001-ARM-dts-BCM5301X-add-missing-LEDs-for-Buffalo-WZR-90.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0001-ARM-dts-BCM5301X-Switch-Luxul-XWC-1000-to-the-new-fi.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0002-ARM-dts-BCM5301X-Relicense-most-DTS-files-to-the-GPL.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0003-ARM-dts-BCM5301X-Relicense-Buffalo-files-to-the-GPL-.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0004-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWR-3150-V1.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0005-ARM-dts-BCM5301X-Add-DT-for-Luxul-XAP-1610.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0006-ARM-dts-BCM5301X-Relicense-Asus-RT-AC87U-file-to-the.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/032-v4.18-0007-ARM-dts-BCM5301X-Switch-D-Link-DIR-885L-to-the-new-p.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/033-v4.19-0001-ARM-dts-BCM5301X-Make-USB-3.0-PHY-use-MDIO-PHY-drive.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/033-v4.19-0002-ARM-dts-BCM53573-Add-architected-timer.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/033-v4.19-0003-ARM-dts-BCM5301X-Add-support-for-Linksys-EA9500.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/034-v4.20-0001-ARM-dts-BCM5301X-Specify-flash-partitions.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/035-v4.21-0001-ARM-dts-BCM5301X-Relicense-BCM47081-BCM4709-files-to.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/035-v4.21-0002-ARM-dts-BCM5301X-Relicense-BCM47094-file-to-the-GPL-.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/035-v4.21-0003-ARM-dts-BCM53573-Relicense-Tenda-AC9-file-to-the-GPL.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/035-v4.21-0004-ARM-dts-BCM53573-Relicense-SoC-file-to-the-GPL-2.0-M.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/035-v4.21-0005-ARM-dts-BCM5301X-Add-basic-DT-for-Linksys-EA6500-V2.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/035-v4.21-0006-ARM-dts-BCM5301X-Describe-Northstar-pins-mux-control.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/036-v5.1-0001-ARM-dts-BCM53573-Relicense-Luxul-files-to-the-GPL-2..patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/036-v5.1-0002-ARM-dts-BCM5301X-Add-basic-DT-for-Phicomm-K3.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/080-spi-bcm53xx-simplify-reading-SPI-data.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/082-pinctrl-bcm-add-Northstar-driver.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/083-pinctrl-bcm-ns-Use-uintptr_t-for-casting-data.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/084-v4.21-pinctrl-bcm-ns-support-updated-DT-binding-as-syscon-.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/321-ARM-dts-BCM5301X-Describe-partition-formats.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/400-mtd-spi-nor-detect-JEDEC-incompatible-w25q128-using-.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch
 delete mode 100644 target/linux/bcm53xx/patches-4.14/905-BCM53573-minor-hacks.patch

diff --git a/target/linux/bcm53xx/config-4.14 b/target/linux/bcm53xx/config-4.14
deleted file mode 100644
index 12da0eec9f..0000000000
--- a/target/linux/bcm53xx/config-4.14
+++ /dev/null
@@ -1,363 +0,0 @@
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_BCM=y
-CONFIG_ARCH_BCM_5301X=y
-CONFIG_ARCH_BCM_53573=y
-CONFIG_ARCH_BCM_IPROC=y
-CONFIG_ARCH_CLOCKSOURCE_DATA=y
-CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-CONFIG_ARCH_HAS_SET_MEMORY=y
-CONFIG_ARCH_HAS_SG_CHAIN=y
-CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
-CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
-CONFIG_ARCH_HAS_TICK_BROADCAST=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-# CONFIG_ARCH_MULTI_CPU_AUTO is not set
-CONFIG_ARCH_MULTI_V6_V7=y
-CONFIG_ARCH_MULTI_V7=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ARCH_TIMER=y
-CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
-# CONFIG_ARM_ATAG_DTB_COMPAT is not set
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_ARM_ERRATA_764369=y
-CONFIG_ARM_ERRATA_775420=y
-CONFIG_ARM_GIC=y
-CONFIG_ARM_GLOBAL_TIMER=y
-CONFIG_ARM_HAS_SG_CHAIN=y
-CONFIG_ARM_HEAVY_MB=y
-CONFIG_ARM_L1_CACHE_SHIFT=6
-CONFIG_ARM_L1_CACHE_SHIFT_6=y
-# CONFIG_ARM_LPAE is not set
-CONFIG_ARM_PATCH_IDIV=y
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-# CONFIG_ARM_THUMBEE is not set
-CONFIG_ARM_VIRT_EXT=y
-CONFIG_ATAGS=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BCM47XX_NVRAM=y
-CONFIG_BCM47XX_SPROM=y
-CONFIG_BCM47XX_WDT=y
-CONFIG_BCMA=y
-CONFIG_BCMA_BLOCKIO=y
-CONFIG_BCMA_DEBUG=y
-CONFIG_BCMA_DRIVER_GMAC_CMN=y
-CONFIG_BCMA_DRIVER_GPIO=y
-CONFIG_BCMA_DRIVER_PCI=y
-CONFIG_BCMA_HOST_PCI=y
-CONFIG_BCMA_HOST_PCI_POSSIBLE=y
-CONFIG_BCMA_HOST_SOC=y
-CONFIG_BCMA_SFLASH=y
-CONFIG_BCM_NET_PHYLIB=y
-CONFIG_BCM_NS_THERMAL=y
-CONFIG_BGMAC=y
-CONFIG_BGMAC_BCMA=y
-# CONFIG_BGMAC_PLATFORM is not set
-CONFIG_BLK_MQ_PCI=y
-CONFIG_BOUNCE=y
-CONFIG_BROADCOM_PHY=y
-CONFIG_CACHE_L2X0=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK=y
-CONFIG_CLKSRC_MMIO=y
-# CONFIG_CLK_BCM_NS2 is not set
-CONFIG_CLK_BCM_NSP=y
-# CONFIG_CLK_BCM_SR is not set
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_COMMON_CLK=y
-CONFIG_COMMON_CLK_IPROC=y
-CONFIG_CPU_32v6K=y
-CONFIG_CPU_32v7=y
-CONFIG_CPU_ABRT_EV7=y
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-CONFIG_CPU_CACHE_V7=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_HAS_ASID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_V7=y
-CONFIG_CPU_RMAP=y
-CONFIG_CPU_THUMB_CAPABLE=y
-CONFIG_CPU_TLB_V7=y
-CONFIG_CPU_V7=y
-CONFIG_CRC16=y
-CONFIG_CRYPTO_ACOMP2=y
-CONFIG_CRYPTO_AEAD=y
-CONFIG_CRYPTO_AEAD2=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_MANAGER=y
-CONFIG_CRYPTO_MANAGER2=y
-CONFIG_CRYPTO_NULL2=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DCACHE_WORD_ACCESS=y
-CONFIG_DEBUG_BCM_5301X=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_LL=y
-CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
-CONFIG_DEBUG_UART_8250=y
-# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
-CONFIG_DEBUG_UART_8250_SHIFT=0
-CONFIG_DEBUG_UART_PHYS=0x18000300
-CONFIG_DEBUG_UART_VIRT=0xf1000300
-CONFIG_DEBUG_UNCOMPRESS=y
-CONFIG_DEBUG_USER=y
-CONFIG_DTC=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_EXTCON=y
-CONFIG_FIXED_PHY=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FRAME_POINTER=y
-# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ARCH_TOPOLOGY=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_EARLY_IOREMAP=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_PINCTRL_GROUPS=y
-CONFIG_GENERIC_PINMUX_FUNCTIONS=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_74X164=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_GRO_CELLS is not set
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDEN_BRANCH_PREDICTOR=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_AUDITSYSCALL=y
-CONFIG_HAVE_ARCH_BITREVERSE=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_ARM_ARCH_TIMER=y
-CONFIG_HAVE_ARM_SCU=y
-CONFIG_HAVE_ARM_SMCCC=y
-CONFIG_HAVE_ARM_TWD=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
-CONFIG_HAVE_EBPF_JIT=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SMP=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HIGHMEM=y
-# CONFIG_HIGHPTE is not set
-CONFIG_HZ_FIXED=0
-CONFIG_HZ_PERIODIC=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IOMMU_HELPER=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_DOMAIN_HIERARCHY=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_SPIN_ON_OWNER=y
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MDIO_BCM_IPROC=y
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_BUS_MUX=y
-# CONFIG_MDIO_BUS_MUX_BCM_IPROC is not set
-CONFIG_MDIO_BUS_MUX_MMIOREG=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MFD_SYSCON=y
-CONFIG_MIGHT_HAVE_CACHE_L2X0=y
-CONFIG_MIGHT_HAVE_PCI=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MTD_BCM47XXSFLASH=y
-CONFIG_MTD_BCM47XX_PARTS=y
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_BRCMNAND=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_PARSER_TRX=y
-# CONFIG_MTD_PHYSMAP_OF is not set
-CONFIG_MTD_SPI_NOR=y
-CONFIG_MTD_SPLIT_SEAMA_FW=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-# CONFIG_MTD_UBI_FASTMAP is not set
-# CONFIG_MTD_UBI_GLUEBI is not set
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_MUTEX_SPIN_ON_OWNER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NET_FLOW_LIMIT=y
-CONFIG_NO_BOOTMEM=y
-CONFIG_NR_CPUS=2
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_ADDRESS_PCI=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_MDIO=y
-CONFIG_OF_NET=y
-CONFIG_OF_PCI=y
-CONFIG_OF_PCI_IRQ=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_OUTER_CACHE=y
-CONFIG_OUTER_CACHE_SYNC=y
-CONFIG_PADATA=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PCI=y
-CONFIG_PCIE_IPROC=y
-CONFIG_PCIE_IPROC_BCMA=y
-# CONFIG_PCIE_IPROC_PLATFORM is not set
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_DOMAINS_GENERIC=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-# CONFIG_PHY_BCM_NS_USB2 is not set
-# CONFIG_PHY_BCM_NS_USB3 is not set
-# CONFIG_PHY_BRCM_SATA is not set
-# CONFIG_PHY_NS2_USB_DRD is not set
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_IPROC_GPIO is not set
-CONFIG_PINCTRL_NS=y
-# CONFIG_PINCTRL_NS2_MUX is not set
-# CONFIG_PL310_ERRATA_588369 is not set
-# CONFIG_PL310_ERRATA_727915 is not set
-# CONFIG_PL310_ERRATA_753970 is not set
-# CONFIG_PL310_ERRATA_769419 is not set
-CONFIG_RATIONAL=y
-CONFIG_RCU_NEED_SEGCBLIST=y
-CONFIG_RCU_STALL_COMMON=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_RFS_ACCEL=y
-CONFIG_RPS=y
-CONFIG_RWSEM_SPIN_ON_OWNER=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-# CONFIG_SCHED_INFO is not set
-# CONFIG_SCSI_DMA is not set
-CONFIG_SERIAL_8250_FSL=y
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SMP=y
-CONFIG_SMP_ON_UP=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPI=y
-# CONFIG_SPI_BCM53XX is not set
-CONFIG_SPI_BCM_QSPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_GPIO=y
-CONFIG_SPI_MASTER=y
-CONFIG_SRCU=y
-CONFIG_SWCONFIG=y
-CONFIG_SWCONFIG_B53=y
-# CONFIG_SWCONFIG_B53_MMAP_DRIVER is not set
-CONFIG_SWCONFIG_B53_PHY_DRIVER=y
-CONFIG_SWCONFIG_B53_PHY_FIXUP=y
-CONFIG_SWCONFIG_B53_SRAB_DRIVER=y
-CONFIG_SWIOTLB=y
-CONFIG_SWPHY=y
-CONFIG_SWP_EMULATE=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_OF=y
-# CONFIG_THUMB2_KERNEL is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TREE_RCU=y
-CONFIG_TREE_SRCU=y
-CONFIG_UBIFS_FS=y
-# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
-CONFIG_UBIFS_FS_LZO=y
-CONFIG_UBIFS_FS_ZLIB=y
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-# CONFIG_VFP is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XPS=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
diff --git a/target/linux/bcm53xx/patches-4.14/030-v4.15-0001-ARM-dts-BCM5301X-Specify-USB-ports-for-USB-LED-of-Lu.patch b/target/linux/bcm53xx/patches-4.14/030-v4.15-0001-ARM-dts-BCM5301X-Specify-USB-ports-for-USB-LED-of-Lu.patch
deleted file mode 100644
index 3148f6c32d..0000000000
--- a/target/linux/bcm53xx/patches-4.14/030-v4.15-0001-ARM-dts-BCM5301X-Specify-USB-ports-for-USB-LED-of-Lu.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 2460266f21f140936e627f28f28d1a4f30887ae9 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Fri, 6 Oct 2017 10:52:35 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul
- XWR-1200
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This info can be used by operating system to setup LED behavior.
-
-Reported-by: Dan Haab <dhaab at luxul.com>
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
-+++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
-@@ -57,7 +57,8 @@
- 		usb {
- 			label = "bcm53xx:green:usb";
- 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
--			linux,default-trigger = "none";
-+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
-+			linux,default-trigger = "usbport";
- 		};
- 
- 		status {
diff --git a/target/linux/bcm53xx/patches-4.14/030-v4.15-0002-ARM-dts-BCM5301X-Add-DT-for-Luxul-XBR-4500.patch b/target/linux/bcm53xx/patches-4.14/030-v4.15-0002-ARM-dts-BCM5301X-Add-DT-for-Luxul-XBR-4500.patch
deleted file mode 100644
index b0dd01d4e5..0000000000
--- a/target/linux/bcm53xx/patches-4.14/030-v4.15-0002-ARM-dts-BCM5301X-Add-DT-for-Luxul-XBR-4500.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 1f4b0d5596d2e3ea8e953d578ab8444ce860d35d Mon Sep 17 00:00:00 2001
-From: Dan Haab <dhaab at luxul.com>
-Date: Mon, 9 Oct 2017 09:46:22 -0600
-Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This is BCM47094 (AKA BCM4709C0) based router with ports-on-the-front
-board design.
-
-Signed-off-by: Dan Haab <dhaab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                    |  1 +
- arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts | 63 +++++++++++++++++++++++++++
- 2 files changed, 64 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm4709-tplink-archer-c9-v1.dtb \
- 	bcm47094-dlink-dir-885l.dtb \
- 	bcm47094-linksys-panamera.dtb \
-+	bcm47094-luxul-xbr-4500.dtb \
- 	bcm47094-luxul-xwr-3100.dtb \
- 	bcm47094-netgear-r8500.dtb \
- 	bcm94708.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-@@ -0,0 +1,63 @@
-+/*
-+ * Copyright (C) 2017 Luxul Inc.
-+ *
-+ * Licensed under the ISC license.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm4708.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+
-+/ {
-+	compatible = "luxul,xbr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
-+	model = "Luxul XBR-4500 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000
-+		       0x88000000 0x18000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		status {
-+			label = "bcm53xx:green:status";
-+			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "timer";
-+		};
-+
-+		usb3 {
-+			label = "bcm53xx:green:usb3";
-+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
-+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
-+				<&xhci_port1>;
-+			linux,default-trigger = "usbport";
-+		};
-+
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&usb3 {
-+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
-+};
-+
-+&spi_nor {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/030-v4.15-0003-ARM-dts-BCM5301X-Add-DT-for-Luxul-ABR-4500.patch b/target/linux/bcm53xx/patches-4.14/030-v4.15-0003-ARM-dts-BCM5301X-Add-DT-for-Luxul-ABR-4500.patch
deleted file mode 100644
index 76bc739dde..0000000000
--- a/target/linux/bcm53xx/patches-4.14/030-v4.15-0003-ARM-dts-BCM5301X-Add-DT-for-Luxul-ABR-4500.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 65f78c4c41a9b9a7637e1dda2d5e41cf26ea971c Mon Sep 17 00:00:00 2001
-From: Dan Haab <dhaab at luxul.com>
-Date: Mon, 9 Oct 2017 09:46:23 -0600
-Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This is BCM47094 (AKA BCM4709C0) based router with rear-facing ports
-board design.
-
-Signed-off-by: Dan Haab <dhaab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                    |  1 +
- arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts | 63 +++++++++++++++++++++++++++
- 2 files changed, 64 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm4709-tplink-archer-c9-v1.dtb \
- 	bcm47094-dlink-dir-885l.dtb \
- 	bcm47094-linksys-panamera.dtb \
-+	bcm47094-luxul-abr-4500.dtb \
- 	bcm47094-luxul-xbr-4500.dtb \
- 	bcm47094-luxul-xwr-3100.dtb \
- 	bcm47094-netgear-r8500.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-@@ -0,0 +1,63 @@
-+/*
-+ * Copyright (C) 2017 Luxul Inc.
-+ *
-+ * Licensed under the ISC license.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm4708.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+
-+/ {
-+	compatible = "luxul,abr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
-+	model = "Luxul ABR-4500 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000
-+		       0x88000000 0x18000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		status {
-+			label = "bcm53xx:green:status";
-+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "timer";
-+		};
-+
-+		usb3 {
-+			label = "bcm53xx:green:usb3";
-+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
-+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
-+				<&xhci_port1>;
-+			linux,default-trigger = "usbport";
-+		};
-+
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&usb3 {
-+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
-+};
-+
-+&spi_nor {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/030-v4.15-0004-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-810.patch b/target/linux/bcm53xx/patches-4.14/030-v4.15-0004-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-810.patch
deleted file mode 100644
index 5cb894c361..0000000000
--- a/target/linux/bcm53xx/patches-4.14/030-v4.15-0004-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-810.patch
+++ /dev/null
@@ -1,120 +0,0 @@
-From 0aa052ce1c3340850a7e5980b6d24b3ea5779591 Mon Sep 17 00:00:00 2001
-From: Dan Haab <dhaab at luxul.com>
-Date: Mon, 9 Oct 2017 09:46:59 -0600
-Subject: [PATCH] ARM: dts: BCM53573: Add DT for Luxul XAP-810
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This is BCM53573 WiSoC based access point with an extra BCM43217 chipset
-used for 2.4 GHz.
-
-Signed-off-by: Dan Haab <dhaab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                   |  1 +
- arch/arm/boot/dts/bcm47189-luxul-xap-810.dts | 87 ++++++++++++++++++++++++++++
- 2 files changed, 88 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -111,6 +111,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm953012hr.dtb \
- 	bcm953012k.dtb
- dtb-$(CONFIG_ARCH_BCM_53573) += \
-+	bcm47189-luxul-xap-810.dtb \
- 	bcm47189-tenda-ac9.dtb \
- 	bcm947189acdbmr.dtb
- dtb-$(CONFIG_ARCH_BCM_63XX) += \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
-@@ -0,0 +1,87 @@
-+/*
-+ * Copyright 2017 Luxul Inc.
-+ *
-+ * Licensed under the ISC license.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm53573.dtsi"
-+
-+/ {
-+	compatible = "luxul,xap-810-v1", "brcm,bcm47189", "brcm,bcm53573";
-+	model = "Luxul XAP-810 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		5ghz {
-+			label = "bcm53xx:blue:5ghz";
-+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "default-off";
-+		};
-+
-+		system {
-+			label = "bcm53xx:green:system";
-+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "timer";
-+		};
-+	};
-+
-+	pcie0_leds {
-+		compatible = "gpio-leds";
-+
-+		2ghz {
-+			label = "bcm53xx:blue:2ghz";
-+			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "default-off";
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&pcie0 {
-+	ranges = <0x00000000 0 0 0 0 0x00100000>;
-+	#address-cells = <3>;
-+	#size-cells = <2>;
-+
-+	bridge at 0,0,0 {
-+		reg = <0x0000 0 0 0 0>;
-+		ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
-+		#address-cells = <3>;
-+		#size-cells = <2>;
-+
-+		wifi at 0,1,0 {
-+			reg = <0x0000 0 0 0 0>;
-+			ranges = <0x00000000 0 0 0 0x00100000>;
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			pcie0_chipcommon: chipcommon at 0 {
-+				reg = <0 0x1000>;
-+
-+				gpio-controller;
-+				#gpio-cells = <2>;
-+			};
-+		};
-+	};
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/030-v4.15-0005-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-1440.patch b/target/linux/bcm53xx/patches-4.14/030-v4.15-0005-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-1440.patch
deleted file mode 100644
index 9d43dd58d0..0000000000
--- a/target/linux/bcm53xx/patches-4.14/030-v4.15-0005-ARM-dts-BCM53573-Add-DT-for-Luxul-XAP-1440.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From 7030ea600d560026b91726f2eb79c856b813afa9 Mon Sep 17 00:00:00 2001
-From: Dan Haab <dhaab at luxul.com>
-Date: Mon, 9 Oct 2017 09:47:00 -0600
-Subject: [PATCH] ARM: dts: BCM53573: Add DT for Luxul XAP-1440
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This is BCM53573 WiSoC based outdoor access point with an extra BCM43217
-chipset used for 2.4 GHz.
-
-Signed-off-by: Dan Haab <dhaab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                    |  1 +
- arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts | 50 +++++++++++++++++++++++++++
- 2 files changed, 51 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -111,6 +111,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm953012hr.dtb \
- 	bcm953012k.dtb
- dtb-$(CONFIG_ARCH_BCM_53573) += \
-+	bcm47189-luxul-xap-1440.dtb \
- 	bcm47189-luxul-xap-810.dtb \
- 	bcm47189-tenda-ac9.dtb \
- 	bcm947189acdbmr.dtb
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
-@@ -0,0 +1,50 @@
-+/*
-+ * Copyright 2017 Luxul Inc.
-+ *
-+ * Licensed under the ISC license.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm53573.dtsi"
-+
-+/ {
-+	compatible = "luxul,xap-1440-v1", "brcm,bcm47189", "brcm,bcm53573";
-+	model = "Luxul XAP-1440 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		wlan {
-+			label = "bcm53xx:blue:wlan";
-+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "default-off";
-+		};
-+
-+		system {
-+			label = "bcm53xx:green:system";
-+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "timer";
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/031-v4.17-0001-ARM-dts-BCM5301X-add-missing-LEDs-for-Buffalo-WZR-90.patch b/target/linux/bcm53xx/patches-4.14/031-v4.17-0001-ARM-dts-BCM5301X-add-missing-LEDs-for-Buffalo-WZR-90.patch
deleted file mode 100644
index 043d38b832..0000000000
--- a/target/linux/bcm53xx/patches-4.14/031-v4.17-0001-ARM-dts-BCM5301X-add-missing-LEDs-for-Buffalo-WZR-90.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 811ae58e76da88106f6d28159d4ea7b163dfaa48 Mon Sep 17 00:00:00 2001
-From: INAGAKI Hiroshi <musashino.open at gmail.com>
-Date: Wed, 7 Mar 2018 20:33:56 +0900
-Subject: [PATCH] ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Buffalo WZR-900DHP has 8 LEDs, but there is not LED definitions in the
-dts and cannot configure these LEDs.
-I Added missing LED definitions for WZR-900DHP.
-
-Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
-Reviewed-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts | 68 +++++++++++++++++++++++
- 1 file changed, 68 insertions(+)
-
---- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
-+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
-@@ -35,6 +35,74 @@
- 		       0x88000000 0x08000000>;
- 	};
- 
-+	spi {
-+		compatible = "spi-gpio";
-+		num-chipselects = <1>;
-+		gpio-sck = <&chipcommon 7 0>;
-+		gpio-mosi = <&chipcommon 4 0>;
-+		cs-gpios = <&chipcommon 6 0>;
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		hc595: gpio_spi at 0 {
-+			compatible = "fairchild,74hc595";
-+			reg = <0>;
-+			registers-number = <1>;
-+			spi-max-frequency = <100000>;
-+
-+			gpio-controller;
-+			#gpio-cells = <2>;
-+
-+		};
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		usb {
-+			label = "bcm53xx:green:usb";
-+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		power0 {
-+			label = "bcm53xx:green:power";
-+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "default-on";
-+		};
-+
-+		power1 {
-+			label = "bcm53xx:red:power";
-+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		router0 {
-+			label = "bcm53xx:green:router";
-+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "default-on";
-+		};
-+
-+		router1 {
-+			label = "bcm53xx:amber:router";
-+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		wan {
-+			label = "bcm53xx:green:wan";
-+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "default-on";
-+		};
-+
-+		wireless0 {
-+			label = "bcm53xx:green:wireless";
-+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		wireless1 {
-+			label = "bcm53xx:amber:wireless";
-+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+
- 	gpio-keys {
- 		compatible = "gpio-keys";
- 		#address-cells = <1>;
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0001-ARM-dts-BCM5301X-Switch-Luxul-XWC-1000-to-the-new-fi.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0001-ARM-dts-BCM5301X-Switch-Luxul-XWC-1000-to-the-new-fi.patch
deleted file mode 100644
index e2fe0be909..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0001-ARM-dts-BCM5301X-Switch-Luxul-XWC-1000-to-the-new-fi.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From 0c0d1c90ddc44df70401b7cfff178c41b2f83ffa Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Wed, 4 Apr 2018 15:14:21 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Switch Luxul XWC-1000 to the new fixed
- partitions syntax
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This new syntax is slightly better designed & uses "compatible" string.
-For details see Documentation/devicetree/bindings/mtd/partition.txt .
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts | 12 +++++++++---
- 1 file changed, 9 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
-+++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
-@@ -26,9 +26,15 @@
- 
- 	nand: nand at 18028000 {
- 		nandcs at 0 {
--			partition at 0 {
--				label = "ubi";
--				reg = <0x00000000 0x08000000>;
-+			partitions {
-+				compatible = "fixed-partitions";
-+				#address-cells = <1>;
-+				#size-cells = <1>;
-+
-+				partition at 0 {
-+					label = "ubi";
-+					reg = <0x00000000 0x08000000>;
-+				};
- 			};
- 		};
- 	};
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0002-ARM-dts-BCM5301X-Relicense-most-DTS-files-to-the-GPL.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0002-ARM-dts-BCM5301X-Relicense-most-DTS-files-to-the-GPL.patch
deleted file mode 100644
index 6599520b92..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0002-ARM-dts-BCM5301X-Relicense-most-DTS-files-to-the-GPL.patch
+++ /dev/null
@@ -1,440 +0,0 @@
-From 2b3db67ce4bc4d1d8556e87a17df7765da8dbdc5 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Wed, 2 May 2018 16:11:02 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Relicense most DTS files to the GPL 2.0+
- / MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-These files were created and ever touched by a group of three people
-only: Dan, Hauke and me. They were licensed under GNU/GPL or ISC.
-
-Introducing and discussing SPDX-License-Identifier resulted in a
-conclusion that ISC is a not recommended license (see also a
-license-rules.rst). Moveover an old e-mail from Alan Cox was pointed
-which explained that dual licensing is a safer solution than depending
-on a common compatibility belief.
-
-This commit switches most of BCM5301X DTS files to dual licensing using:
-1) GPL 2.0+ to make sure they are compatible with Linux kernel
-2) MIT to allow sharing with more permissive projects
-Both licenses belong to the preferred ones (see LICENSES/preferred/).
-
-An attempt to relicense remaining files will be made separately and will
-require approve from more/other developers.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Reviewed-by: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
-Acked-by: Hauke Mehrtens <hauke at hauke-m.de>
-Acked-by: Dan Haab <dan.haab at luxul.com>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts        | 13 +------------
- arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts        | 13 +------------
- arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts    |  3 +--
- arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts       |  3 +--
- arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts       |  3 +--
- arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts     | 13 +------------
- arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts      |  3 +--
- arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts        | 13 +------------
- arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts | 13 +------------
- arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts      |  3 +--
- arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts      |  3 +--
- arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts |  3 +--
- arch/arm/boot/dts/bcm4709-linksys-ea9200.dts       |  3 +--
- arch/arm/boot/dts/bcm4709-netgear-r7000.dts        | 13 +------------
- arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts  |  3 +--
- arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts      | 13 +------------
- arch/arm/boot/dts/bcm47094-linksys-panamera.dts    |  3 +--
- arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts      |  3 +--
- arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts      |  3 +--
- arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts      |  3 +--
- arch/arm/boot/dts/bcm47094-netgear-r8500.dts       |  3 +--
- arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi      |  3 +--
- arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi      |  3 +--
- arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi      |  3 +--
- arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi           |  3 +--
- 25 files changed, 25 insertions(+), 120 deletions(-)
-
---- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
-+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Asus RT-AC56U
-  *
-  * Copyright (C) 2015 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
-+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Asus RT-AC68U
-  *
-  * Copyright (C) 2015 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
-+++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2017 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
-+++ b/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2016 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
-+++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
-@@ -1,10 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Luxul XWC-1000
-  *
-  * Copyright 2014 Luxul Inc.
-- *
-- * Licensed under the GNU/GPL. See COPYING for details.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
-+++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Netgear R6300 V2
-  *
-  * Copyright (C) 2014 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
-+++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
-@@ -1,10 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X arm platform code.
-  * DTS for SmartRG SR400ac
-  *
-  * Copyright (C) 2015 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Licensed under the GNU/GPL. See COPYING for details.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
-+++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Asus RT-N18U
-  *
-  * Copyright (C) 2014 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
-+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Buffalo WZR-600DHP2
-  *
-  * Copyright (C) 2014 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
-+++ b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2017 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
-+++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2017 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-+++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2017 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
-+++ b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2017 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
-+++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Netgear R7000
-  *
-  * Copyright (C) 2015 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
-+++ b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for D-Link DIR-885L
-  *
-  * Copyright (C) 2016 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
-+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2017 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2017 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2017 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2016 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
-+++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi
-@@ -1,9 +1,8 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom Northstar NAND.
-  *
-  * Copyright (C) 2016 Rafał Miłecki <rafal.milecki at gmail.com>
-- *
-- * Licensed under the ISC license.
-  */
- 
- #include "bcm5301x-nand-cs0.dtsi"
---- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2016 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- #include "bcm5301x-nand-cs0.dtsi"
---- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi
-@@ -1,3 +1,4 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X Nand chip defaults.
-  *
-@@ -5,8 +6,6 @@
-  * and uses 8 bit ECC.
-  *
-  * Copyright (C) 2015 Hauke Mehrtens <hauke at hauke-m.de>
-- *
-- * Licensed under the GNU/GPL. See COPYING for details.
-  */
- 
- #include "bcm5301x-nand-cs0.dtsi"
---- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
-@@ -1,9 +1,8 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom Northstar NAND.
-  *
-  * Copyright (C) 2015 Hauke Mehrtens <hauke at hauke-m.de>
-- *
-- * Licensed under the GNU/GPL. See COPYING for details.
-  */
- 
- / {
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0003-ARM-dts-BCM5301X-Relicense-Buffalo-files-to-the-GPL-.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0003-ARM-dts-BCM5301X-Relicense-Buffalo-files-to-the-GPL-.patch
deleted file mode 100644
index cc7ff8552a..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0003-ARM-dts-BCM5301X-Relicense-Buffalo-files-to-the-GPL-.patch
+++ /dev/null
@@ -1,79 +0,0 @@
-From fd0ab539d185a828f2071ee5f311bf101c7fea08 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Fri, 4 May 2018 11:54:45 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Relicense Buffalo files to the GPL 2.0+ /
- MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by other BCM5301X files and is preferred as:
-1) GPL 2.0+ makes is clearly compatible with Linux kernel
-2) MIT is also permissive but preferred over ISC
-
-These files were created and ever touched by a group of four people
-only: Felix, INAGAKI, Hauke and me.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Acked-by: Felix Fietkau <nbd at nbd.name>
-Acked-by: INAGAKI Hiroshi <musashino.open at gmail.com>
-Acked-by: Hauke Mehrtens <hauke at hauke-m.de>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts |  3 +--
- arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts | 13 +------------
- arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts |  3 +--
- 3 files changed, 3 insertions(+), 16 deletions(-)
-
---- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
-+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
-@@ -1,10 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Buffalo WZR-1750DHP
-  *
-  * Copyright (C) 2014 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Licensed under the GNU/GPL. See COPYING for details.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
-+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Buffalo WZR-900DHP
-  *
-  * Copyright (C) 2015 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
-+++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
-@@ -1,10 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Buffalo WXR-1900DHP
-  *
-  * Copyright (C) 2015 Felix Fietkau <nbd at openwrt.org>
-- *
-- * Licensed under the GNU/GPL. See COPYING for details.
-  */
- 
- /dts-v1/;
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0004-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWR-3150-V1.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0004-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWR-3150-V1.patch
deleted file mode 100644
index 4285a59a6d..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0004-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWR-3150-V1.patch
+++ /dev/null
@@ -1,112 +0,0 @@
-From 2e2105a1578172eaf61e3b59a2c10c4fe04c21b9 Mon Sep 17 00:00:00 2001
-From: Dan Haab <riproute at gmail.com>
-Date: Fri, 4 May 2018 10:08:43 -0600
-Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XWR-3150 V1
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Luxul XWR-3150 is a wireless router similar to the XWR-3100 except:
-1) It has more RAM
-2) Its NAND controller in running in BCH8 mode
-3) LAN ports LEDs are hardware controlled
-
-Signed-off-by: Dan Haab <dan.haab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                       |  1 +
- arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts | 77 ++++++++++++++++++++++++
- 2 files changed, 78 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -104,6 +104,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm47094-luxul-abr-4500.dtb \
- 	bcm47094-luxul-xbr-4500.dtb \
- 	bcm47094-luxul-xwr-3100.dtb \
-+	bcm47094-luxul-xwr-3150-v1.dtb \
- 	bcm47094-netgear-r8500.dtb \
- 	bcm94708.dtb \
- 	bcm94709.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
-@@ -0,0 +1,77 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright 2018 Luxul Inc.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm47094.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+
-+/ {
-+	compatible = "luxul,xwr-3150-v1", "brcm,bcm47094", "brcm,bcm4708";
-+	model = "Luxul XWR-3150 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000
-+		       0x88000000 0x18000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		power	{
-+			label = "bcm53xx:green:power";
-+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "default-on";
-+		};
-+
-+		usb3	{
-+			label = "bcm53xx:green:usb3";
-+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
-+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
-+					  <&xhci_port1>;
-+			linux,default-trigger = "usbport";
-+		};
-+
-+		status	{
-+			label = "bcm53xx:green:status";
-+			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "timer";
-+		};
-+
-+		2ghz {
-+			label = "bcm53xx:green:2ghz";
-+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		5ghz {
-+			label = "bcm53xx:green:5ghz";
-+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&usb3 {
-+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
-+};
-+
-+&spi_nor {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0005-ARM-dts-BCM5301X-Add-DT-for-Luxul-XAP-1610.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0005-ARM-dts-BCM5301X-Add-DT-for-Luxul-XAP-1610.patch
deleted file mode 100644
index a6102857c3..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0005-ARM-dts-BCM5301X-Add-DT-for-Luxul-XAP-1610.patch
+++ /dev/null
@@ -1,90 +0,0 @@
-From 6054cb5788072e214af582c42d9bd8c5ffa6e288 Mon Sep 17 00:00:00 2001
-From: Dan Haab <riproute at gmail.com>
-Date: Fri, 4 May 2018 10:08:44 -0600
-Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XAP-1610
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-It's an access point based on BCM47094 SoC with two BCM4366E wireless
-chipsets.
-
-Signed-off-by: Dan Haab <dan.haab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                    |  1 +
- arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts | 57 +++++++++++++++++++++++++++
- 2 files changed, 58 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm47094-dlink-dir-885l.dtb \
- 	bcm47094-linksys-panamera.dtb \
- 	bcm47094-luxul-abr-4500.dtb \
-+	bcm47094-luxul-xap-1610.dtb \
- 	bcm47094-luxul-xbr-4500.dtb \
- 	bcm47094-luxul-xwr-3100.dtb \
- 	bcm47094-luxul-xwr-3150-v1.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
-@@ -0,0 +1,57 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright 2018 Luxul Inc.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm47094.dtsi"
-+
-+/ {
-+	compatible = "luxul,xap-1610-v1", "brcm,bcm47094", "brcm,bcm4708";
-+	model = "Luxul XAP-1610 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		status	{
-+			label = "bcm53xx:green:status";
-+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "timer";
-+		};
-+
-+		2ghz {
-+			label = "bcm53xx:blue:2ghz";
-+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		5ghz {
-+			label = "bcm53xx:blue:5ghz";
-+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&spi_nor {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0006-ARM-dts-BCM5301X-Relicense-Asus-RT-AC87U-file-to-the.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0006-ARM-dts-BCM5301X-Relicense-Asus-RT-AC87U-file-to-the.patch
deleted file mode 100644
index f774bc6b82..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0006-ARM-dts-BCM5301X-Relicense-Asus-RT-AC87U-file-to-the.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From 9c281b5e129961b9940a27f8da24dddd1c0eba87 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Fri, 4 May 2018 12:03:24 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Relicense Asus RT-AC87U file to the GPL
- 2.0+ / MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by other BCM5301X files and is preferred as:
-1) GPL 2.0+ makes is clearly compatible with Linux kernel
-2) MIT is also permissive but preferred over ISC
-
-This file were created and ever touched by a group of three people only:
-Álvaro, Hauke and me.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Acked-by: Hauke Mehrtens <hauke at hauke-m.de>
-Acked-by: Álvaro Fernández Rojas <noltari at gmail.com>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 13 +------------
- 1 file changed, 1 insertion(+), 12 deletions(-)
-
---- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
-+++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for Asus RT-AC87U
-  *
-  * Copyright (C) 2015 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- /dts-v1/;
diff --git a/target/linux/bcm53xx/patches-4.14/032-v4.18-0007-ARM-dts-BCM5301X-Switch-D-Link-DIR-885L-to-the-new-p.patch b/target/linux/bcm53xx/patches-4.14/032-v4.18-0007-ARM-dts-BCM5301X-Switch-D-Link-DIR-885L-to-the-new-p.patch
deleted file mode 100644
index e397ddd0b2..0000000000
--- a/target/linux/bcm53xx/patches-4.14/032-v4.18-0007-ARM-dts-BCM5301X-Switch-D-Link-DIR-885L-to-the-new-p.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From a05f1e36a57d02374a203719abc5bf2e8c51e125 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 10 May 2018 23:20:00 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Switch D-Link DIR-885L to the new
- partitions syntax
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This new syntax is slightly better designed & uses "compatible" string.
-For details see Documentation/devicetree/bindings/mtd/partition.txt .
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 12 +++++++++---
- 1 file changed, 9 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-@@ -26,9 +26,15 @@
- 
- 	nand: nand at 18028000 {
- 		nandcs at 0 {
--			partition at 0 {
--				label = "firmware";
--				reg = <0x00000000 0x08000000>;
-+			partitions {
-+				compatible = "fixed-partitions";
-+				#address-cells = <1>;
-+				#size-cells = <1>;
-+
-+				partition at 0 {
-+					label = "firmware";
-+					reg = <0x00000000 0x08000000>;
-+				};
- 			};
- 		};
- 	};
diff --git a/target/linux/bcm53xx/patches-4.14/033-v4.19-0001-ARM-dts-BCM5301X-Make-USB-3.0-PHY-use-MDIO-PHY-drive.patch b/target/linux/bcm53xx/patches-4.14/033-v4.19-0001-ARM-dts-BCM5301X-Make-USB-3.0-PHY-use-MDIO-PHY-drive.patch
deleted file mode 100644
index 226109c09c..0000000000
--- a/target/linux/bcm53xx/patches-4.14/033-v4.19-0001-ARM-dts-BCM5301X-Make-USB-3.0-PHY-use-MDIO-PHY-drive.patch
+++ /dev/null
@@ -1,456 +0,0 @@
-From 37f6130ec39fe14e923d472746a51e6f06f761b7 Mon Sep 17 00:00:00 2001
-From: Vivek Unune <npcomplete13 at gmail.com>
-Date: Mon, 9 Apr 2018 18:31:53 -0400
-Subject: [PATCH] ARM: dts: BCM5301X: Make USB 3.0 PHY use MDIO PHY driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Currently, the USB 3.0 PHY in bcm5301x.dtsi uses platform driver which
-requires register range "ccb-mii" <0x18003000 0x1000>. This range
-overlaps with MDIO cmd and param registers (<0x18003000 0x8>).
-Essentially, the platform driver partly acts like a MDIO bus driver,
-hence to use of this register range.
-
-In some Northstar devices like Linksys EA9500, secondary switch is
-connected via external MDIO. The only way to access and configure the
-external switch is via MDIO bus. When we enable the MDIO bus in it's
-current state, the MDIO bus and any child buses fail to register because
-of the register range overlap.
-
-On Northstar, the USB 3.0 PHY is connected at address 0x10 on the
-internal MDIO bus. This change moves the usb3_phy node and makes it a
-child node of internal MDIO bus.
-
-Thanks to Rafał Miłecki's commit af850e14a7ae ("phy: bcm-ns-usb3: add
-MDIO driver using proper bus layer") the same USB 3.0 platform driver
-can now act as USB 3.0 PHY MDIO driver.
-
-Tested on Linksys Panamera (EA9500)
-
-Signed-off-by: Vivek Unune <npcomplete13 at gmail.com>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts        |  4 +++
- arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts        |  4 +++
- arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts  |  4 +++
- arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts    |  4 +++
- arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts       |  4 +++
- arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts       |  4 +++
- arch/arm/boot/dts/bcm4708-netgear-r6250.dts        |  4 +++
- arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts     |  4 +++
- arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts      |  4 +++
- arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts        |  4 +++
- arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts |  4 +++
- arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts  |  4 +++
- arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts      |  4 +++
- arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts      |  4 +++
- arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts |  4 +++
- arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts        |  4 +++
- arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts  |  4 +++
- arch/arm/boot/dts/bcm4709-linksys-ea9200.dts       |  4 +++
- arch/arm/boot/dts/bcm4709-netgear-r7000.dts        |  4 +++
- arch/arm/boot/dts/bcm4709-netgear-r8000.dts        |  4 +++
- arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts  |  4 +++
- arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts      |  4 +++
- arch/arm/boot/dts/bcm47094-linksys-panamera.dts    |  4 +++
- arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts      |  4 +++
- arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts      |  4 +++
- arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts      |  4 +++
- arch/arm/boot/dts/bcm47094-netgear-r8500.dts       |  4 +++
- arch/arm/boot/dts/bcm47094.dtsi                    |  7 +++--
- arch/arm/boot/dts/bcm5301x.dtsi                    | 35 +++++++++++++++++-----
- arch/arm/boot/dts/bcm94708.dts                     |  4 +++
- arch/arm/boot/dts/bcm94709.dts                     |  4 +++
- arch/arm/boot/dts/bcm953012er.dts                  |  4 +++
- arch/arm/boot/dts/bcm953012hr.dts                  |  4 +++
- arch/arm/boot/dts/bcm953012k.dts                   |  4 +++
- 34 files changed, 159 insertions(+), 11 deletions(-)
-
---- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
-+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
-@@ -90,3 +90,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
-+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
-@@ -80,3 +80,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
-+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
-@@ -146,3 +146,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
-+++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
-@@ -38,3 +38,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
-+++ b/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
-@@ -57,3 +57,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
-+++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
-@@ -64,3 +64,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
-+++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
-@@ -91,3 +91,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
-+++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
-@@ -83,3 +83,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
-+++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
-@@ -158,3 +158,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
-+++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
-@@ -74,3 +74,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
-+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
-@@ -118,3 +118,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
-+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
-@@ -104,3 +104,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
-+++ b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
-@@ -57,3 +57,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
-+++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
-@@ -105,3 +105,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-+++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-@@ -99,3 +99,7 @@
- &usb2 {
- 	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
-+++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
-@@ -62,3 +62,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
-+++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
-@@ -127,3 +127,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
-+++ b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
-@@ -39,3 +39,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
-+++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
-@@ -101,3 +101,7 @@
- &usb3 {
- 	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
-+++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
-@@ -182,3 +182,7 @@
- &usb3 {
- 	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
-+++ b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
-@@ -104,3 +104,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-@@ -115,3 +115,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
-+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
-@@ -33,3 +33,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-@@ -60,3 +60,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-@@ -60,3 +60,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
-@@ -100,3 +100,7 @@
- &spi_nor {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
-+++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
-@@ -91,3 +91,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm47094.dtsi
-+++ b/arch/arm/boot/dts/bcm47094.dtsi
-@@ -7,9 +7,10 @@
- #include "bcm4708.dtsi"
- 
- / {
--	usb3_phy: usb3-phy {
--		compatible = "brcm,ns-bx-usb3-phy";
--	};
-+};
-+
-+&usb3_phy {
-+	compatible = "brcm,ns-bx-usb3-phy";
- };
- 
- &uart0 {
---- a/arch/arm/boot/dts/bcm5301x.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x.dtsi
-@@ -154,13 +154,6 @@
- 		clock-names = "phy-ref-clk";
- 	};
- 
--	usb3_phy: usb3-phy {
--		compatible = "brcm,ns-ax-usb3-phy";
--		reg = <0x18105000 0x1000>, <0x18003000 0x1000>;
--		reg-names = "dmp", "ccb-mii";
--		#phy-cells = <0>;
--	};
--
- 	axi at 18000000 {
- 		compatible = "brcm,bus-axi";
- 		reg = <0x18000000 0x1000>;
-@@ -359,7 +352,33 @@
- 		reg = <0x18003000 0x8>;
- 		#size-cells = <1>;
- 		#address-cells = <0>;
--		status = "disabled";
-+	};
-+
-+	mdio-bus-mux {
-+		compatible = "mdio-mux-mmioreg";
-+		mdio-parent-bus = <&mdio>;
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		reg = <0x18003000 0x4>;
-+		mux-mask = <0x200>;
-+
-+		mdio at 0 {
-+			reg = <0x0>;
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+
-+			usb3_phy: usb3-phy at 10 {
-+				compatible = "brcm,ns-ax-usb3-phy";
-+				reg = <0x10>;
-+				usb3-dmp-syscon = <&usb3_dmp>;
-+				#phy-cells = <0>;
-+				status = "disabled";
-+			};
-+		};
-+	};
-+
-+	usb3_dmp: syscon at 18105000 {
-+		reg = <0x18105000 0x1000>;
- 	};
- 
- 	i2c0: i2c at 18009000 {
---- a/arch/arm/boot/dts/bcm94708.dts
-+++ b/arch/arm/boot/dts/bcm94708.dts
-@@ -42,3 +42,7 @@
- 		reg = <0x00000000 0x08000000>;
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm94709.dts
-+++ b/arch/arm/boot/dts/bcm94709.dts
-@@ -42,3 +42,7 @@
- 		reg = <0x00000000 0x08000000>;
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm953012er.dts
-+++ b/arch/arm/boot/dts/bcm953012er.dts
-@@ -90,3 +90,7 @@
- 		};
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm953012hr.dts
-+++ b/arch/arm/boot/dts/bcm953012hr.dts
-@@ -95,3 +95,7 @@
- 		reg = <0x00700000 0x00900000>;
- 	};
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
---- a/arch/arm/boot/dts/bcm953012k.dts
-+++ b/arch/arm/boot/dts/bcm953012k.dts
-@@ -113,3 +113,7 @@
- &uart1 {
- 	status = "okay";
- };
-+
-+&usb3_phy {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/033-v4.19-0002-ARM-dts-BCM53573-Add-architected-timer.patch b/target/linux/bcm53xx/patches-4.14/033-v4.19-0002-ARM-dts-BCM53573-Add-architected-timer.patch
deleted file mode 100644
index f1b301ca27..0000000000
--- a/target/linux/bcm53xx/patches-4.14/033-v4.19-0002-ARM-dts-BCM53573-Add-architected-timer.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From a21e7548438f3a8f59f9b9f3a8bc973613d3726a Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 14 Jun 2018 18:41:47 +0200
-Subject: [PATCH] ARM: dts: BCM53573: Add architected timer
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-It's a standard ARM architected timer that was simply missed when
-initially adding this .dtsi file.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm53573.dtsi | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/arch/arm/boot/dts/bcm53573.dtsi
-+++ b/arch/arm/boot/dts/bcm53573.dtsi
-@@ -48,6 +48,14 @@
- 		};
- 	};
- 
-+	timer {
-+		compatible = "arm,armv7-timer";
-+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
-+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
-+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
-+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
-+	};
-+
- 	clocks {
- 		#address-cells = <1>;
- 		#size-cells = <1>;
diff --git a/target/linux/bcm53xx/patches-4.14/033-v4.19-0003-ARM-dts-BCM5301X-Add-support-for-Linksys-EA9500.patch b/target/linux/bcm53xx/patches-4.14/033-v4.19-0003-ARM-dts-BCM5301X-Add-support-for-Linksys-EA9500.patch
deleted file mode 100644
index 701605a973..0000000000
--- a/target/linux/bcm53xx/patches-4.14/033-v4.19-0003-ARM-dts-BCM5301X-Add-support-for-Linksys-EA9500.patch
+++ /dev/null
@@ -1,269 +0,0 @@
-From 2bebdfcdcd0feb58d5df419532a2cedc78a336d7 Mon Sep 17 00:00:00 2001
-From: Vivek Unune <npcomplete13 at gmail.com>
-Date: Mon, 18 Jun 2018 13:41:59 -0400
-Subject: [PATCH] ARM: dts: BCM5301X: Add support for Linksys EA9500
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Hardware Info
--------------
-
-Processor	- Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
-Switch		- BCM53012 in BCM4709C0KFEBG & external BCM53125
-DDR3 RAM	- 256 MB
-Flash		- 128 MB (Toshiba TC58BVG0S3HTA00)
-2.4GHz		- BCM4366 4×4 2.4/5G single chip 802.11ac SoC
-Power Amp	- Skyworks SE2623L 2.4 GHz power amp (x4)
-5GHz x 2	- BCM4366 4×4 2.4/5G single chip 802.11ac SoC
-Power Amp	- PLX Technology PEX8603 3-lane, 3-port PCIe switch
-Ports		- 8 Ports, 1 WAN Ports
-Antennas	- 8 Antennas
-Serial Port	- @J6 [GND,TX,RX] (VCC NC)    115200 8n1
-
-Tested with OpenWrt built with DSA driver and Kernel v4.14
-
-Signed-off-by: Vivek Unune <npcomplete13 at gmail.com>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 229 ++++++++++++++++++++++++
- 1 file changed, 229 insertions(+)
-
---- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
-+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
-@@ -31,6 +31,235 @@
- 			linux,code = <KEY_WPS_BUTTON>;
- 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
- 		};
-+
-+		rfkill {
-+				label = "WiFi";
-+				linux,code = <KEY_RFKILL>;
-+				gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		reset {
-+				label = "Reset";
-+				linux,code = <KEY_RESTART>;
-+				gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		wps {
-+			label = "bcm53xx:white:wps";
-+			gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		usb2 {
-+			label = "bcm53xx:green:usb2";
-+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
-+			trigger-sources = <&ohci_port2>, <&ehci_port2>;
-+			linux,default-trigger = "usbport";
-+		};
-+
-+		usb3 {
-+			label = "bcm53xx:green:usb3";
-+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
-+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
-+					  <&xhci_port1>;
-+			linux,default-trigger = "usbport";
-+		};
-+
-+		power {
-+			label = "bcm53xx:white:power";
-+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		wifi-disabled {
-+			label = "bcm53xx:amber:wifi-disabled";
-+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		wifi-enabled {
-+			label = "bcm53xx:white:wifi-enabled";
-+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar1 {
-+			label = "bcm53xx:white:bluebar1";
-+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar2 {
-+			label = "bcm53xx:white:bluebar2";
-+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar3 {
-+			label = "bcm53xx:white:bluebar3";
-+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		bluebar4 {
-+			label = "bcm53xx:white:bluebar4";
-+			gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar5 {
-+			label = "bcm53xx:white:bluebar5";
-+			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar6 {
-+			label = "bcm53xx:white:bluebar6";
-+			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar7 {
-+			label = "bcm53xx:white:bluebar7";
-+			gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		bluebar8 {
-+			label = "bcm53xx:white:bluebar8";
-+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+
-+	mdio-bus-mux {
-+		/* BIT(9) = 1 => external mdio */
-+		mdio_ext: mdio at 200 {
-+			reg = <0x200>;
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+		};
-+	};
-+
-+	mdio-mii-mux {
-+		compatible = "mdio-mux-mmioreg";
-+		mdio-parent-bus = <&mdio_ext>;
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		reg = <0x1800c1c0 0x4>;
-+
-+		/* BIT(6) = mdc, BIT(7) = mdio */
-+		mux-mask = <0xc0>;
-+
-+		mdio-mii at 0 {
-+			/* Enable MII function */
-+			reg = <0x0>;
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+
-+			switch at 0  {
-+				compatible = "brcm,bcm53125";
-+				#address-cells = <1>;
-+				#size-cells = <0>;
-+				reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-+				reset-names = "robo_reset";
-+				reg = <0>;
-+				dsa,member = <1 0>;
-+
-+				ports {
-+					#address-cells = <1>;
-+					#size-cells = <0>;
-+
-+					port at 0 {
-+						reg = <0>;
-+						label = "lan1";
-+					};
-+
-+					port at 1 {
-+						reg = <1>;
-+						label = "lan5";
-+					};
-+
-+					port at 2 {
-+						reg = <2>;
-+						label = "lan2";
-+					};
-+
-+					port at 3 {
-+						reg = <3>;
-+						label = "lan6";
-+					};
-+
-+					port at 4 {
-+						reg = <4>;
-+						label = "lan3";
-+					};
-+
-+					sw1_p8: port at 8 {
-+						reg = <8>;
-+						ethernet = <&sw0_p0>;
-+						label = "cpu";
-+
-+						fixed-link {
-+							speed = <1000>;
-+							full-duplex;
-+						};
-+					};
-+				};
-+			};
-+		};
-+	};
-+};
-+
-+&usb2 {
-+	vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
-+};
-+
-+&usb3 {
-+	vcc-gpio = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
-+};
-+
-+&srab {
-+	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
-+	status = "okay";
-+	dsa,member = <0 0>;
-+
-+	ports {
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		port at 1 {
-+			reg = <1>;
-+			label = "lan7";
-+		};
-+
-+		port at 2 {
-+			reg = <2>;
-+			label = "lan4";
-+		};
-+
-+		port at 3 {
-+			reg = <3>;
-+			label = "lan8";
-+		};
-+
-+		port at 4 {
-+			reg = <4>;
-+			label = "wan";
-+		};
-+
-+		port at 8 {
-+			reg = <8>;
-+			ethernet = <&gmac2>;
-+			label = "cpu";
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
-+
-+		sw0_p0: port at 0 {
-+			reg = <0>;
-+			label = "extsw";
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
- 	};
- };
- 
diff --git a/target/linux/bcm53xx/patches-4.14/034-v4.20-0001-ARM-dts-BCM5301X-Specify-flash-partitions.patch b/target/linux/bcm53xx/patches-4.14/034-v4.20-0001-ARM-dts-BCM5301X-Specify-flash-partitions.patch
deleted file mode 100644
index e6e2522f08..0000000000
--- a/target/linux/bcm53xx/patches-4.14/034-v4.20-0001-ARM-dts-BCM5301X-Specify-flash-partitions.patch
+++ /dev/null
@@ -1,167 +0,0 @@
-From b0465fdfdd7e7c1afe2fae1cb36b94e1ce89732e Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Sat, 28 Jul 2018 14:13:57 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Specify flash partitions
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Most devices use Broadcom standard partitions which allows them to be
-described with the "brcm,bcm947xx-cfe-partitions". Exceptions are:
-1) TP-LINK devices which use "os-image" partition with TRX containing
-   kernel only + separated rootfs partition.
-2) Asus RT-AC87U with custom "asus" partition.
-
-This commit also removes undocumented and unsupported linux,part-probe
-binding which got accidentally upstreamed while describing SPI
-controller.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts | 28 +++++++++++++++++++
- arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts        | 31 ++++++++++++++++++++++
- arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts  | 28 +++++++++++++++++++
- arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi           |  4 +++
- arch/arm/boot/dts/bcm5301x.dtsi                    |  5 +++-
- 5 files changed, 95 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-+++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-@@ -94,6 +94,34 @@
- 
- &spi_nor {
- 	status = "okay";
-+
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		boot at 0 {
-+			label = "boot";
-+			reg = <0x000000 0x040000>;
-+			read-only;
-+		};
-+
-+		os-image at 100000 {
-+			label = "os-image";
-+			reg = <0x040000 0x200000>;
-+			compatible = "brcm,trx";
-+		};
-+
-+		rootfs at 240000 {
-+			label = "rootfs";
-+			reg = <0x240000 0xc00000>;
-+		};
-+
-+		nvram at ff0000 {
-+			label = "nvram";
-+			reg = <0xff0000 0x010000>;
-+		};
-+	};
- };
- 
- &usb2 {
---- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
-+++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
-@@ -66,3 +66,34 @@
- &usb3_phy {
- 	status = "okay";
- };
-+
-+&nandcs {
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		boot at 0 {
-+			label = "boot";
-+			reg = <0x00000000 0x00080000>;
-+			read-only;
-+		};
-+
-+		nvram at 80000 {
-+			label = "nvram";
-+			reg = <0x00080000 0x00180000>;
-+		};
-+
-+		firmware at 200000 {
-+			label = "firmware";
-+			reg = <0x00200000 0x07cc0000>;
-+			compatible = "brcm,trx";
-+		};
-+
-+		asus at 7ec0000 {
-+			label = "asus";
-+			reg = <0x07ec0000 0x00140000>;
-+			read-only;
-+		};
-+	};
-+};
---- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
-+++ b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
-@@ -103,6 +103,34 @@
- 
- &spi_nor {
- 	status = "okay";
-+
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		boot at 0 {
-+			label = "boot";
-+			reg = <0x000000 0x040000>;
-+			read-only;
-+		};
-+
-+		os-image at 100000 {
-+			label = "os-image";
-+			reg = <0x040000 0x200000>;
-+			compatible = "brcm,trx";
-+		};
-+
-+		rootfs at 240000 {
-+			label = "rootfs";
-+			reg = <0x240000 0xc00000>;
-+		};
-+
-+		nvram at ff0000 {
-+			label = "nvram";
-+			reg = <0xff0000 0x010000>;
-+		};
-+	};
- };
- 
- &usb3_phy {
---- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
-@@ -12,6 +12,10 @@
- 			reg = <0>;
- 			#address-cells = <1>;
- 			#size-cells = <1>;
-+
-+			partitions {
-+				compatible = "brcm,bcm947xx-cfe-partitions";
-+			};
- 		};
- 	};
- };
---- a/arch/arm/boot/dts/bcm5301x.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x.dtsi
-@@ -475,8 +475,11 @@
- 			compatible = "jedec,spi-nor";
- 			reg = <0>;
- 			spi-max-frequency = <20000000>;
--			linux,part-probe = "ofpart", "bcm47xxpart";
- 			status = "disabled";
-+
-+			partitions {
-+				compatible = "brcm,bcm947xx-cfe-partitions";
-+			};
- 		};
- 	};
- 
diff --git a/target/linux/bcm53xx/patches-4.14/035-v4.21-0001-ARM-dts-BCM5301X-Relicense-BCM47081-BCM4709-files-to.patch b/target/linux/bcm53xx/patches-4.14/035-v4.21-0001-ARM-dts-BCM5301X-Relicense-BCM47081-BCM4709-files-to.patch
deleted file mode 100644
index 2dc6b2c23c..0000000000
--- a/target/linux/bcm53xx/patches-4.14/035-v4.21-0001-ARM-dts-BCM5301X-Relicense-BCM47081-BCM4709-files-to.patch
+++ /dev/null
@@ -1,58 +0,0 @@
-From 26ff86f7794b9466481ccf29ac79925d327f106d Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 20 Sep 2018 13:18:47 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Relicense BCM47081/BCM4709 files to the
- GPL 2.0+ / MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by other BCM5301X files and is preferred as:
-1) GPL 2.0+ makes it clearly compatible with Linux kernel
-2) MIT is also permissive but preferred over ISC
-
-Both files were fully developed by me. Commits touching them were signed
-by Florian and Hauke due to submitting process only.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47081.dtsi | 13 +------------
- arch/arm/boot/dts/bcm4709.dtsi  |  3 +--
- 2 files changed, 2 insertions(+), 14 deletions(-)
-
---- a/arch/arm/boot/dts/bcm47081.dtsi
-+++ b/arch/arm/boot/dts/bcm47081.dtsi
-@@ -1,20 +1,9 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Broadcom BCM470X / BCM5301X ARM platform code.
-  * DTS for BCM47081 SoC.
-  *
-  * Copyright © 2014 Rafał Miłecki <zajec5 at gmail.com>
-- *
-- * Permission to use, copy, modify, and/or distribute this software for any
-- * purpose with or without fee is hereby granted, provided that the above
-- * copyright notice and this permission notice appear in all copies.
-- *
-- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH
-- * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
-- * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT,
-- * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
-- * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
-- * OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
-- * PERFORMANCE OF THIS SOFTWARE.
-  */
- 
- #include "bcm5301x.dtsi"
---- a/arch/arm/boot/dts/bcm4709.dtsi
-+++ b/arch/arm/boot/dts/bcm4709.dtsi
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- #include "bcm4708.dtsi"
diff --git a/target/linux/bcm53xx/patches-4.14/035-v4.21-0002-ARM-dts-BCM5301X-Relicense-BCM47094-file-to-the-GPL-.patch b/target/linux/bcm53xx/patches-4.14/035-v4.21-0002-ARM-dts-BCM5301X-Relicense-BCM47094-file-to-the-GPL-.patch
deleted file mode 100644
index 86c6b0ae41..0000000000
--- a/target/linux/bcm53xx/patches-4.14/035-v4.21-0002-ARM-dts-BCM5301X-Relicense-BCM47094-file-to-the-GPL-.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From d10967344375026ca8762b6080dec2585d895906 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 20 Sep 2018 13:20:19 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Relicense BCM47094 file to the GPL 2.0+ /
- MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by other BCM5301X files and is preferred as:
-1) GPL 2.0+ makes it clearly compatible with Linux kernel
-2) MIT is also permissive but preferred over ISC
-
-This file has been developed by me & once modified by Vivek.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Acked-by: Vivek Unune <npcomplete13 at gmail.com>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47094.dtsi | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm47094.dtsi
-+++ b/arch/arm/boot/dts/bcm47094.dtsi
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- #include "bcm4708.dtsi"
diff --git a/target/linux/bcm53xx/patches-4.14/035-v4.21-0003-ARM-dts-BCM53573-Relicense-Tenda-AC9-file-to-the-GPL.patch b/target/linux/bcm53xx/patches-4.14/035-v4.21-0003-ARM-dts-BCM53573-Relicense-Tenda-AC9-file-to-the-GPL.patch
deleted file mode 100644
index a5358b70c3..0000000000
--- a/target/linux/bcm53xx/patches-4.14/035-v4.21-0003-ARM-dts-BCM53573-Relicense-Tenda-AC9-file-to-the-GPL.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 1c9001b4f69a37820862286b3bbcdde152a52dcf Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 20 Sep 2018 13:37:47 +0200
-Subject: [PATCH] ARM: dts: BCM53573: Relicense Tenda AC9 file to the GPL 2.0+
- / MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by most of BCM5301X files and is preferred as:
-1) GPL 2.0+ makes it clearly compatible with Linux kernel
-2) MIT is also permissive but preferred over ISC
-
-This file was fully developed by me.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47189-tenda-ac9.dts | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
-+++ b/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
diff --git a/target/linux/bcm53xx/patches-4.14/035-v4.21-0004-ARM-dts-BCM53573-Relicense-SoC-file-to-the-GPL-2.0-M.patch b/target/linux/bcm53xx/patches-4.14/035-v4.21-0004-ARM-dts-BCM53573-Relicense-SoC-file-to-the-GPL-2.0-M.patch
deleted file mode 100644
index 56cd6376aa..0000000000
--- a/target/linux/bcm53xx/patches-4.14/035-v4.21-0004-ARM-dts-BCM53573-Relicense-SoC-file-to-the-GPL-2.0-M.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From ca3a6e705cad10662827093d5426abe078861793 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 20 Sep 2018 13:39:28 +0200
-Subject: [PATCH] ARM: dts: BCM53573: Relicense SoC file to the GPL 2.0+ / MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by most of BCM5301X files and is preferred as:
-1) GPL 2.0+ makes it clearly compatible with Linux kernel
-2) MIT is also permissive but preferred over ISC
-
-This file has been developed by me & once modified by Rob dropping a
-single leading zero in an UART address.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Acked-by: Rob Herring <robh at kernel.org>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm53573.dtsi | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm53573.dtsi
-+++ b/arch/arm/boot/dts/bcm53573.dtsi
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
-- *
-- * Licensed under the ISC license.
-  */
- 
- #include <dt-bindings/gpio/gpio.h>
diff --git a/target/linux/bcm53xx/patches-4.14/035-v4.21-0005-ARM-dts-BCM5301X-Add-basic-DT-for-Linksys-EA6500-V2.patch b/target/linux/bcm53xx/patches-4.14/035-v4.21-0005-ARM-dts-BCM5301X-Add-basic-DT-for-Linksys-EA6500-V2.patch
deleted file mode 100644
index d657d7ab1c..0000000000
--- a/target/linux/bcm53xx/patches-4.14/035-v4.21-0005-ARM-dts-BCM5301X-Add-basic-DT-for-Linksys-EA6500-V2.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From 03e96644d7a810916fc4997d572577e876908b18 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Ren=C3=A9=20Kjellerup?= <rk.katana.steel at gmail.com>
-Date: Mon, 1 Oct 2018 15:07:16 -0700
-Subject: [PATCH] ARM: dts: BCM5301X: Add basic DT for Linksys EA6500 V2
-
-It is wireless home router based on BCM4708A0 with BCM4360 + BCM4331
-wireless chipsets. The BCM4331 5GHz chip currently isn't supported only
-due to missing compatible firmware.
-
-Signed-off-by: Rene Kjellerup <rk.katana.steel at gmail.com>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                      |  1 +
- arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts | 45 +++++++++++++++++++++++++
- 2 files changed, 46 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -82,6 +82,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm4708-asus-rt-ac68u.dtb \
- 	bcm4708-buffalo-wzr-1750dhp.dtb \
- 	bcm4708-linksys-ea6300-v1.dtb \
-+	bcm4708-linksys-ea6500-v2.dtb \
- 	bcm4708-luxul-xap-1510.dtb \
- 	bcm4708-luxul-xwc-1000.dtb \
- 	bcm4708-netgear-r6250.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
-@@ -0,0 +1,45 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (C) 2017 Rafał Miłecki <rafal at milecki.pl>
-+ * Copyright (C) 2018 Rene Kjellerup <rk.katana.steel at gmail.com>
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm4708.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+
-+/ {
-+	compatible = "linksys,ea6500-v2", "brcm,bcm4708";
-+	model = "Linksys EA6500 V2";
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000>;
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		wps {
-+			label = "WPS";
-+			linux,code = <KEY_WPS_BUTTON>;
-+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&usb3_phy {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/035-v4.21-0006-ARM-dts-BCM5301X-Describe-Northstar-pins-mux-control.patch b/target/linux/bcm53xx/patches-4.14/035-v4.21-0006-ARM-dts-BCM5301X-Describe-Northstar-pins-mux-control.patch
deleted file mode 100644
index 5f6dd17dc7..0000000000
--- a/target/linux/bcm53xx/patches-4.14/035-v4.21-0006-ARM-dts-BCM5301X-Describe-Northstar-pins-mux-control.patch
+++ /dev/null
@@ -1,77 +0,0 @@
-From 9994241ac97cb84d1df98fdc172d3cc6b04b11bf Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Fri, 9 Nov 2018 09:56:49 +0100
-Subject: [PATCH] ARM: dts: BCM5301X: Describe Northstar pins mux controller
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This describes hardware & will allow referencing pin functions. The
-first usage is UART1 which allows supporting devices using it.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm5301x.dtsi | 44 +++++++++++++++++++++++++++++++++++++++++
- 1 file changed, 44 insertions(+)
-
---- a/arch/arm/boot/dts/bcm5301x.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x.dtsi
-@@ -37,6 +37,8 @@
- 			reg = <0x0400 0x100>;
- 			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
- 			clocks = <&iprocslow>;
-+			pinctrl-names = "default";
-+			pinctrl-0 = <&pinmux_uart1>;
- 			status = "disabled";
- 		};
- 	};
-@@ -391,6 +393,48 @@
- 		status = "disabled";
- 	};
- 
-+	dmu at 1800c000 {
-+		compatible = "simple-bus";
-+		ranges = <0 0x1800c000 0x1000>;
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		cru at 100 {
-+			compatible = "simple-bus";
-+			reg = <0x100 0x1a4>;
-+			ranges;
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			pin-controller at 1c0 {
-+				compatible = "brcm,bcm4708-pinmux";
-+				reg = <0x1c0 0x24>;
-+				reg-names = "cru_gpio_control";
-+
-+				spi-pins {
-+					groups = "spi_grp";
-+					function = "spi";
-+				};
-+
-+				i2c {
-+					groups = "i2c_grp";
-+					function = "i2c";
-+				};
-+
-+				pwm {
-+					groups = "pwm0_grp", "pwm1_grp",
-+						 "pwm2_grp", "pwm3_grp";
-+					function = "pwm";
-+				};
-+
-+				pinmux_uart1: uart1 {
-+					groups = "uart1_grp";
-+					function = "uart1";
-+				};
-+			};
-+		};
-+	};
-+
- 	lcpll0: lcpll0 at 1800c100 {
- 		#clock-cells = <1>;
- 		compatible = "brcm,nsp-lcpll0";
diff --git a/target/linux/bcm53xx/patches-4.14/036-v5.1-0001-ARM-dts-BCM53573-Relicense-Luxul-files-to-the-GPL-2..patch b/target/linux/bcm53xx/patches-4.14/036-v5.1-0001-ARM-dts-BCM53573-Relicense-Luxul-files-to-the-GPL-2..patch
deleted file mode 100644
index 5883577d53..0000000000
--- a/target/linux/bcm53xx/patches-4.14/036-v5.1-0001-ARM-dts-BCM53573-Relicense-Luxul-files-to-the-GPL-2..patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From b7f264fa496eb2a6dd1d67dc91dbe8ffcb142487 Mon Sep 17 00:00:00 2001
-From: Dan Haab <riproute at gmail.com>
-Date: Sun, 2 Dec 2018 17:00:15 -0700
-Subject: [PATCH] ARM: dts: BCM53573: Relicense Luxul files to the GPL 2.0+ /
- MIT
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This matches licensing used by other BCM53573 files and BCM5301X.
-
-Signed-off-by: Dan Haab <dan.haab at luxul.com>
-Acked-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts | 3 +--
- arch/arm/boot/dts/bcm47189-luxul-xap-810.dts  | 3 +--
- 2 files changed, 2 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
-+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2017 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
---- a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
-+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
-@@ -1,7 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
- /*
-  * Copyright 2017 Luxul Inc.
-- *
-- * Licensed under the ISC license.
-  */
- 
- /dts-v1/;
diff --git a/target/linux/bcm53xx/patches-4.14/036-v5.1-0002-ARM-dts-BCM5301X-Add-basic-DT-for-Phicomm-K3.patch b/target/linux/bcm53xx/patches-4.14/036-v5.1-0002-ARM-dts-BCM5301X-Add-basic-DT-for-Phicomm-K3.patch
deleted file mode 100644
index d77dedbacf..0000000000
--- a/target/linux/bcm53xx/patches-4.14/036-v5.1-0002-ARM-dts-BCM5301X-Add-basic-DT-for-Phicomm-K3.patch
+++ /dev/null
@@ -1,107 +0,0 @@
-From 40a17923367118e32e5e413a952736dd83635b32 Mon Sep 17 00:00:00 2001
-From: Hao Dong <halbertdong at gmail.com>
-Date: Sun, 20 Jan 2019 23:33:27 +0100
-Subject: [PATCH] ARM: dts: BCM5301X: Add basic DT for Phicomm K3
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This router has BCM4709C0 SoC, 128 MiB NAND flash (MX30LF1G18AC-TI),
-512 MiB memory and 3 x LAN and 1 x WAN ports. WiFi chips are
-BCM4366C0 x 2. The router has a small LCD and 3 capactive keys driven by
-a PIC microcontroller, which is in turn wired to UART1 of main board.
-
-Signed-off-by: Hao Dong <halbertdong at gmail.com>
-[rmilecki: drop chosen { }, fix whitespaces, update commit message]
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
----
- arch/arm/boot/dts/Makefile                |  1 +
- arch/arm/boot/dts/bcm47094-phicomm-k3.dts | 71 +++++++++++++++++++++++
- 2 files changed, 72 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47094-phicomm-k3.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -108,6 +108,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm47094-luxul-xwr-3100.dtb \
- 	bcm47094-luxul-xwr-3150-v1.dtb \
- 	bcm47094-netgear-r8500.dtb \
-+	bcm47094-phicomm-k3.dtb \
- 	bcm94708.dtb \
- 	bcm94709.dtb \
- 	bcm953012er.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
-@@ -0,0 +1,71 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (C) 2017 Hamster Tian <haotia at gmail.com>
-+ * Copyright (C) 2019 Hao Dong <halbertdong at gmail.com>
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm47094.dtsi"
-+#include "bcm5301x-nand-cs0-bch4.dtsi"
-+
-+/ {
-+	compatible = "phicomm,k3", "brcm,bcm47094", "brcm,bcm4708";
-+	model = "Phicomm K3";
-+
-+	memory {
-+		reg = <0x00000000 0x08000000
-+		       0x88000000 0x18000000>;
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&uart1 {
-+	status = "okay";
-+};
-+
-+&usb3_phy {
-+	status = "okay";
-+};
-+
-+&nandcs {
-+	partitions {
-+		compatible = "fixed-partitions";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+
-+		partition at 0 {
-+			label = "boot";
-+			reg = <0x0000000 0x0080000>;
-+			read-only;
-+		};
-+
-+		partition at 80000 {
-+			label = "nvram";
-+			reg = <0x0080000 0x0100000>;
-+		};
-+
-+		partition at 180000{
-+			label = "phicomm";
-+			reg = <0x0180000 0x0280000>;
-+			read-only;
-+		};
-+
-+		partition at 400000 {
-+			label = "firmware";
-+			reg = <0x0400000 0x7C00000>;
-+			compatible = "brcm,trx";
-+		};
-+	};
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/080-spi-bcm53xx-simplify-reading-SPI-data.patch b/target/linux/bcm53xx/patches-4.14/080-spi-bcm53xx-simplify-reading-SPI-data.patch
deleted file mode 100644
index ee377c491f..0000000000
--- a/target/linux/bcm53xx/patches-4.14/080-spi-bcm53xx-simplify-reading-SPI-data.patch
+++ /dev/null
@@ -1,107 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Fri, 29 Dec 2017 14:44:09 +0100
-Subject: [PATCH] spi: bcm53xx: simplify reading SPI data
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This commit makes transfer function use spi_transfer_is_last to
-determine if currently processed transfer is the last one. Thanks to
-that we finally set hardware registers properly and it makes controller
-behave the way it's expected to.
-
-This allows simplifying read function which can now simply start reading
-from the slot 0 instead of the last saved offset. It has been
-successfully tested using spi_write_then_read.
-
-Moreover this change fixes handling messages with two writing transfers.
-It's important for SPI flash devices as their drivers commonly use one
-transfer for a command and another one for data.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
----
- drivers/spi/spi-bcm53xx.c | 26 ++++++++++----------------
- 1 file changed, 10 insertions(+), 16 deletions(-)
-
---- a/drivers/spi/spi-bcm53xx.c
-+++ b/drivers/spi/spi-bcm53xx.c
-@@ -27,8 +27,6 @@ struct bcm53xxspi {
- 	struct bcma_device *core;
- 	struct spi_master *master;
- 	void __iomem *mmio_base;
--
--	size_t read_offset;
- 	bool bspi;				/* Boot SPI mode with memory mapping */
- };
- 
-@@ -172,8 +170,6 @@ static void bcm53xxspi_buf_write(struct
- 
- 	if (!cont)
- 		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
--
--	b53spi->read_offset = len;
- }
- 
- static void bcm53xxspi_buf_read(struct bcm53xxspi *b53spi, u8 *r_buf,
-@@ -182,10 +178,10 @@ static void bcm53xxspi_buf_read(struct b
- 	u32 tmp;
- 	int i;
- 
--	for (i = 0; i < b53spi->read_offset + len; i++) {
-+	for (i = 0; i < len; i++) {
- 		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
- 		      B53SPI_CDRAM_PCS_DSCK;
--		if (!cont && i == b53spi->read_offset + len - 1)
-+		if (!cont && i == len - 1)
- 			tmp &= ~B53SPI_CDRAM_CONT;
- 		tmp &= ~0x1;
- 		/* Command Register File */
-@@ -194,8 +190,7 @@ static void bcm53xxspi_buf_read(struct b
- 
- 	/* Set queue pointers */
- 	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
--	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP,
--			 b53spi->read_offset + len - 1);
-+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
- 
- 	if (cont)
- 		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
-@@ -214,13 +209,11 @@ static void bcm53xxspi_buf_read(struct b
- 		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
- 
- 	for (i = 0; i < len; ++i) {
--		int offset = b53spi->read_offset + i;
-+		u16 reg = B53SPI_MSPI_RXRAM + 4 * (1 + i * 2);
- 
- 		/* Data stored in the transmit register file LSB */
--		r_buf[i] = (u8)bcm53xxspi_read(b53spi, B53SPI_MSPI_RXRAM + 4 * (1 + offset * 2));
-+		r_buf[i] = (u8)bcm53xxspi_read(b53spi, reg);
- 	}
--
--	b53spi->read_offset = 0;
- }
- 
- static int bcm53xxspi_transfer_one(struct spi_master *master,
-@@ -238,7 +231,8 @@ static int bcm53xxspi_transfer_one(struc
- 		left = t->len;
- 		while (left) {
- 			size_t to_write = min_t(size_t, 16, left);
--			bool cont = left - to_write > 0;
-+			bool cont = !spi_transfer_is_last(master, t) ||
-+				    left - to_write > 0;
- 
- 			bcm53xxspi_buf_write(b53spi, buf, to_write, cont);
- 			left -= to_write;
-@@ -250,9 +244,9 @@ static int bcm53xxspi_transfer_one(struc
- 		buf = (u8 *)t->rx_buf;
- 		left = t->len;
- 		while (left) {
--			size_t to_read = min_t(size_t, 16 - b53spi->read_offset,
--					       left);
--			bool cont = left - to_read > 0;
-+			size_t to_read = min_t(size_t, 16, left);
-+			bool cont = !spi_transfer_is_last(master, t) ||
-+				    left - to_read > 0;
- 
- 			bcm53xxspi_buf_read(b53spi, buf, to_read, cont);
- 			left -= to_read;
diff --git a/target/linux/bcm53xx/patches-4.14/082-pinctrl-bcm-add-Northstar-driver.patch b/target/linux/bcm53xx/patches-4.14/082-pinctrl-bcm-add-Northstar-driver.patch
deleted file mode 100644
index 1d1b038b41..0000000000
--- a/target/linux/bcm53xx/patches-4.14/082-pinctrl-bcm-add-Northstar-driver.patch
+++ /dev/null
@@ -1,427 +0,0 @@
-From c12fb1774deaa9c9408b19db8d43d3612f6e47a0 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Wed, 26 Sep 2018 21:31:03 +0200
-Subject: [PATCH] pinctrl: bcm: add Northstar driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This driver provides support for Northstar mux controller. It differs
-from Northstar Plus one so a new binding and driver were needed.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
----
- drivers/pinctrl/bcm/Kconfig      |  13 ++
- drivers/pinctrl/bcm/Makefile     |   1 +
- drivers/pinctrl/bcm/pinctrl-ns.c | 372 +++++++++++++++++++++++++++++++++++++++
- 3 files changed, 386 insertions(+)
- create mode 100644 drivers/pinctrl/bcm/pinctrl-ns.c
-
---- a/drivers/pinctrl/bcm/Kconfig
-+++ b/drivers/pinctrl/bcm/Kconfig
-@@ -72,6 +72,19 @@ config PINCTRL_CYGNUS_MUX
- 	  configuration, with the exception that certain individual pins
- 	  can be overridden to GPIO function
- 
-+config PINCTRL_NS
-+	bool "Broadcom Northstar pins driver"
-+	depends on OF && (ARCH_BCM_5301X || COMPILE_TEST)
-+	select PINMUX
-+	select GENERIC_PINCONF
-+	default ARCH_BCM_5301X
-+	help
-+	  Say yes here to enable the Broadcom NS SoC pins driver.
-+
-+	  The Broadcom Northstar pins driver supports muxing multi-purpose pins
-+	  that can be used for various functions (e.g. SPI, I2C, UART) as well
-+	  as GPIOs.
-+
- config PINCTRL_NSP_GPIO
- 	bool "Broadcom NSP GPIO (with PINCONF) driver"
- 	depends on OF_GPIO && (ARCH_BCM_NSP || COMPILE_TEST)
---- a/drivers/pinctrl/bcm/Makefile
-+++ b/drivers/pinctrl/bcm/Makefile
-@@ -5,6 +5,7 @@ obj-$(CONFIG_PINCTRL_BCM281XX)		+= pinct
- obj-$(CONFIG_PINCTRL_BCM2835)		+= pinctrl-bcm2835.o
- obj-$(CONFIG_PINCTRL_IPROC_GPIO)	+= pinctrl-iproc-gpio.o
- obj-$(CONFIG_PINCTRL_CYGNUS_MUX)	+= pinctrl-cygnus-mux.o
-+obj-$(CONFIG_PINCTRL_NS)		+= pinctrl-ns.o
- obj-$(CONFIG_PINCTRL_NSP_GPIO)		+= pinctrl-nsp-gpio.o
- obj-$(CONFIG_PINCTRL_NS2_MUX)		+= pinctrl-ns2-mux.o
- obj-$(CONFIG_PINCTRL_NSP_MUX)		+= pinctrl-nsp-mux.o
---- /dev/null
-+++ b/drivers/pinctrl/bcm/pinctrl-ns.c
-@@ -0,0 +1,372 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2018 Rafał Miłecki <rafal at milecki.pl>
-+ */
-+
-+#include <linux/err.h>
-+#include <linux/io.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_device.h>
-+#include <linux/pinctrl/pinconf-generic.h>
-+#include <linux/pinctrl/pinctrl.h>
-+#include <linux/pinctrl/pinmux.h>
-+#include <linux/platform_device.h>
-+#include <linux/slab.h>
-+
-+#define FLAG_BCM4708		BIT(1)
-+#define FLAG_BCM4709		BIT(2)
-+#define FLAG_BCM53012		BIT(3)
-+
-+struct ns_pinctrl {
-+	struct device *dev;
-+	unsigned int chipset_flag;
-+	struct pinctrl_dev *pctldev;
-+	void __iomem *base;
-+
-+	struct pinctrl_desc pctldesc;
-+	struct ns_pinctrl_group *groups;
-+	unsigned int num_groups;
-+	struct ns_pinctrl_function *functions;
-+	unsigned int num_functions;
-+};
-+
-+/*
-+ * Pins
-+ */
-+
-+static const struct pinctrl_pin_desc ns_pinctrl_pins[] = {
-+	{ 0, "spi_clk", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 1, "spi_ss", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 2, "spi_mosi", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 3, "spi_miso", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 4, "i2c_scl", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 5, "i2c_sda", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 6, "mdc", (void *)(FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 7, "mdio", (void *)(FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 8, "pwm0", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 9, "pwm1", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 10, "pwm2", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 11, "pwm3", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 12, "uart1_rx", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 13, "uart1_tx", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 14, "uart1_cts", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 15, "uart1_rts", (void *)(FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 16, "uart2_rx", (void *)(FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 17, "uart2_tx", (void *)(FLAG_BCM4709 | FLAG_BCM53012) },
-+/* TODO { ??, "xtal_out", (void *)(FLAG_BCM4709) }, */
-+	{ 22, "sdio_pwr", (void *)(FLAG_BCM4709 | FLAG_BCM53012) },
-+	{ 23, "sdio_en_1p8v", (void *)(FLAG_BCM4709 | FLAG_BCM53012) },
-+};
-+
-+/*
-+ * Groups
-+ */
-+
-+struct ns_pinctrl_group {
-+	const char *name;
-+	const unsigned int *pins;
-+	const unsigned int num_pins;
-+	unsigned int chipsets;
-+};
-+
-+static const unsigned int spi_pins[] = { 0, 1, 2, 3 };
-+static const unsigned int i2c_pins[] = { 4, 5 };
-+static const unsigned int mdio_pins[] = { 6, 7 };
-+static const unsigned int pwm0_pins[] = { 8 };
-+static const unsigned int pwm1_pins[] = { 9 };
-+static const unsigned int pwm2_pins[] = { 10 };
-+static const unsigned int pwm3_pins[] = { 11 };
-+static const unsigned int uart1_pins[] = { 12, 13, 14, 15 };
-+static const unsigned int uart2_pins[] = { 16, 17 };
-+static const unsigned int sdio_pwr_pins[] = { 22 };
-+static const unsigned int sdio_1p8v_pins[] = { 23 };
-+
-+#define NS_GROUP(_name, _pins, _chipsets)		\
-+{							\
-+	.name = _name,					\
-+	.pins = _pins,					\
-+	.num_pins = ARRAY_SIZE(_pins),			\
-+	.chipsets = _chipsets,				\
-+}
-+
-+static const struct ns_pinctrl_group ns_pinctrl_groups[] = {
-+	NS_GROUP("spi_grp", spi_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("i2c_grp", i2c_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("mdio_grp", mdio_pins, FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("pwm0_grp", pwm0_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("pwm1_grp", pwm1_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("pwm2_grp", pwm2_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("pwm3_grp", pwm3_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("uart1_grp", uart1_pins, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("uart2_grp", uart2_pins, FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("sdio_pwr_grp", sdio_pwr_pins, FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_GROUP("sdio_1p8v_grp", sdio_1p8v_pins, FLAG_BCM4709 | FLAG_BCM53012),
-+};
-+
-+/*
-+ * Functions
-+ */
-+
-+struct ns_pinctrl_function {
-+	const char *name;
-+	const char * const *groups;
-+	const unsigned int num_groups;
-+	unsigned int chipsets;
-+};
-+
-+static const char * const spi_groups[] = { "spi_grp" };
-+static const char * const i2c_groups[] = { "i2c_grp" };
-+static const char * const mdio_groups[] = { "mdio_grp" };
-+static const char * const pwm_groups[] = { "pwm0_grp", "pwm1_grp", "pwm2_grp",
-+					   "pwm3_grp" };
-+static const char * const uart1_groups[] = { "uart1_grp" };
-+static const char * const uart2_groups[] = { "uart2_grp" };
-+static const char * const sdio_groups[] = { "sdio_pwr_grp", "sdio_1p8v_grp" };
-+
-+#define NS_FUNCTION(_name, _groups, _chipsets)		\
-+{							\
-+	.name = _name,					\
-+	.groups = _groups,				\
-+	.num_groups = ARRAY_SIZE(_groups),		\
-+	.chipsets = _chipsets,				\
-+}
-+
-+static const struct ns_pinctrl_function ns_pinctrl_functions[] = {
-+	NS_FUNCTION("spi", spi_groups, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_FUNCTION("i2c", i2c_groups, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_FUNCTION("mdio", mdio_groups, FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_FUNCTION("pwm", pwm_groups, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_FUNCTION("uart1", uart1_groups, FLAG_BCM4708 | FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_FUNCTION("uart2", uart2_groups, FLAG_BCM4709 | FLAG_BCM53012),
-+	NS_FUNCTION("sdio", sdio_groups, FLAG_BCM4709 | FLAG_BCM53012),
-+};
-+
-+/*
-+ * Groups code
-+ */
-+
-+static int ns_pinctrl_get_groups_count(struct pinctrl_dev *pctrl_dev)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+
-+	return ns_pinctrl->num_groups;
-+}
-+
-+static const char *ns_pinctrl_get_group_name(struct pinctrl_dev *pctrl_dev,
-+					     unsigned int selector)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+
-+	return ns_pinctrl->groups[selector].name;
-+}
-+
-+static int ns_pinctrl_get_group_pins(struct pinctrl_dev *pctrl_dev,
-+				     unsigned int selector,
-+				     const unsigned int **pins,
-+				     unsigned int *num_pins)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+
-+	*pins = ns_pinctrl->groups[selector].pins;
-+	*num_pins = ns_pinctrl->groups[selector].num_pins;
-+
-+	return 0;
-+}
-+
-+static const struct pinctrl_ops ns_pinctrl_ops = {
-+	.get_groups_count = ns_pinctrl_get_groups_count,
-+	.get_group_name = ns_pinctrl_get_group_name,
-+	.get_group_pins = ns_pinctrl_get_group_pins,
-+	.dt_node_to_map = pinconf_generic_dt_node_to_map_group,
-+	.dt_free_map = pinconf_generic_dt_free_map,
-+};
-+
-+/*
-+ * Functions code
-+ */
-+
-+static int ns_pinctrl_get_functions_count(struct pinctrl_dev *pctrl_dev)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+
-+	return ns_pinctrl->num_functions;
-+}
-+
-+static const char *ns_pinctrl_get_function_name(struct pinctrl_dev *pctrl_dev,
-+						unsigned int selector)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+
-+	return ns_pinctrl->functions[selector].name;
-+}
-+
-+static int ns_pinctrl_get_function_groups(struct pinctrl_dev *pctrl_dev,
-+					  unsigned int selector,
-+					  const char * const **groups,
-+					  unsigned * const num_groups)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+
-+	*groups = ns_pinctrl->functions[selector].groups;
-+	*num_groups = ns_pinctrl->functions[selector].num_groups;
-+
-+	return 0;
-+}
-+
-+static int ns_pinctrl_set_mux(struct pinctrl_dev *pctrl_dev,
-+			      unsigned int func_select,
-+			      unsigned int grp_select)
-+{
-+	struct ns_pinctrl *ns_pinctrl = pinctrl_dev_get_drvdata(pctrl_dev);
-+	u32 unset = 0;
-+	u32 tmp;
-+	int i;
-+
-+	for (i = 0; i < ns_pinctrl->groups[grp_select].num_pins; i++) {
-+		int pin_number = ns_pinctrl->groups[grp_select].pins[i];
-+
-+		unset |= BIT(pin_number);
-+	}
-+
-+	tmp = readl(ns_pinctrl->base);
-+	tmp &= ~unset;
-+	writel(tmp, ns_pinctrl->base);
-+
-+	return 0;
-+}
-+
-+static const struct pinmux_ops ns_pinctrl_pmxops = {
-+	.get_functions_count = ns_pinctrl_get_functions_count,
-+	.get_function_name = ns_pinctrl_get_function_name,
-+	.get_function_groups = ns_pinctrl_get_function_groups,
-+	.set_mux = ns_pinctrl_set_mux,
-+};
-+
-+/*
-+ * Controller code
-+ */
-+
-+static struct pinctrl_desc ns_pinctrl_desc = {
-+	.name = "pinctrl-ns",
-+	.pctlops = &ns_pinctrl_ops,
-+	.pmxops = &ns_pinctrl_pmxops,
-+};
-+
-+static const struct of_device_id ns_pinctrl_of_match_table[] = {
-+	{ .compatible = "brcm,bcm4708-pinmux", .data = (void *)FLAG_BCM4708, },
-+	{ .compatible = "brcm,bcm4709-pinmux", .data = (void *)FLAG_BCM4709, },
-+	{ .compatible = "brcm,bcm53012-pinmux", .data = (void *)FLAG_BCM53012, },
-+	{ }
-+};
-+
-+static int ns_pinctrl_probe(struct platform_device *pdev)
-+{
-+	struct device *dev = &pdev->dev;
-+	const struct of_device_id *of_id;
-+	struct ns_pinctrl *ns_pinctrl;
-+	struct pinctrl_desc *pctldesc;
-+	struct pinctrl_pin_desc *pin;
-+	struct ns_pinctrl_group *group;
-+	struct ns_pinctrl_function *function;
-+	struct resource *res;
-+	int i;
-+
-+	ns_pinctrl = devm_kzalloc(dev, sizeof(*ns_pinctrl), GFP_KERNEL);
-+	if (!ns_pinctrl)
-+		return -ENOMEM;
-+	pctldesc = &ns_pinctrl->pctldesc;
-+	platform_set_drvdata(pdev, ns_pinctrl);
-+
-+	/* Set basic properties */
-+
-+	ns_pinctrl->dev = dev;
-+
-+	of_id = of_match_device(ns_pinctrl_of_match_table, dev);
-+	if (!of_id)
-+		return -EINVAL;
-+	ns_pinctrl->chipset_flag = (unsigned int)of_id->data;
-+
-+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-+					   "cru_gpio_control");
-+	ns_pinctrl->base = devm_ioremap_resource(dev, res);
-+	if (IS_ERR(ns_pinctrl->base)) {
-+		dev_err(dev, "Failed to map pinctrl regs\n");
-+		return PTR_ERR(ns_pinctrl->base);
-+	}
-+
-+	memcpy(pctldesc, &ns_pinctrl_desc, sizeof(*pctldesc));
-+
-+	/* Set pinctrl properties */
-+
-+	pctldesc->pins = devm_kcalloc(dev, ARRAY_SIZE(ns_pinctrl_pins),
-+				      sizeof(struct pinctrl_pin_desc),
-+				      GFP_KERNEL);
-+	if (!pctldesc->pins)
-+		return -ENOMEM;
-+	for (i = 0, pin = (struct pinctrl_pin_desc *)&pctldesc->pins[0];
-+	     i < ARRAY_SIZE(ns_pinctrl_pins); i++) {
-+		const struct pinctrl_pin_desc *src = &ns_pinctrl_pins[i];
-+		unsigned int chipsets = (unsigned int)src->drv_data;
-+
-+		if (chipsets & ns_pinctrl->chipset_flag) {
-+			memcpy(pin++, src, sizeof(*src));
-+			pctldesc->npins++;
-+		}
-+	}
-+
-+	ns_pinctrl->groups = devm_kcalloc(dev, ARRAY_SIZE(ns_pinctrl_groups),
-+					  sizeof(struct ns_pinctrl_group),
-+					  GFP_KERNEL);
-+	if (!ns_pinctrl->groups)
-+		return -ENOMEM;
-+	for (i = 0, group = &ns_pinctrl->groups[0];
-+	     i < ARRAY_SIZE(ns_pinctrl_groups); i++) {
-+		const struct ns_pinctrl_group *src = &ns_pinctrl_groups[i];
-+
-+		if (src->chipsets & ns_pinctrl->chipset_flag) {
-+			memcpy(group++, src, sizeof(*src));
-+			ns_pinctrl->num_groups++;
-+		}
-+	}
-+
-+	ns_pinctrl->functions = devm_kcalloc(dev,
-+					     ARRAY_SIZE(ns_pinctrl_functions),
-+					     sizeof(struct ns_pinctrl_function),
-+					     GFP_KERNEL);
-+	if (!ns_pinctrl->functions)
-+		return -ENOMEM;
-+	for (i = 0, function = &ns_pinctrl->functions[0];
-+	     i < ARRAY_SIZE(ns_pinctrl_functions); i++) {
-+		const struct ns_pinctrl_function *src = &ns_pinctrl_functions[i];
-+
-+		if (src->chipsets & ns_pinctrl->chipset_flag) {
-+			memcpy(function++, src, sizeof(*src));
-+			ns_pinctrl->num_functions++;
-+		}
-+	}
-+
-+	/* Register */
-+
-+	ns_pinctrl->pctldev = devm_pinctrl_register(dev, pctldesc, ns_pinctrl);
-+	if (IS_ERR(ns_pinctrl->pctldev)) {
-+		dev_err(dev, "Failed to register pinctrl\n");
-+		return PTR_ERR(ns_pinctrl->pctldev);
-+	}
-+
-+	return 0;
-+}
-+
-+static struct platform_driver ns_pinctrl_driver = {
-+	.probe = ns_pinctrl_probe,
-+	.driver = {
-+		.name = "ns-pinmux",
-+		.of_match_table = ns_pinctrl_of_match_table,
-+	},
-+};
-+
-+module_platform_driver(ns_pinctrl_driver);
-+
-+MODULE_AUTHOR("Rafał Miłecki");
-+MODULE_LICENSE("GPL v2");
-+MODULE_DEVICE_TABLE(of, ns_pinctrl_of_match_table);
diff --git a/target/linux/bcm53xx/patches-4.14/083-pinctrl-bcm-ns-Use-uintptr_t-for-casting-data.patch b/target/linux/bcm53xx/patches-4.14/083-pinctrl-bcm-ns-Use-uintptr_t-for-casting-data.patch
deleted file mode 100644
index afaed68d05..0000000000
--- a/target/linux/bcm53xx/patches-4.14/083-pinctrl-bcm-ns-Use-uintptr_t-for-casting-data.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From ce7bdb957b8e3f1cbf0a3358f1deef385dff6502 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 11 Oct 2018 13:23:40 +0200
-Subject: [PATCH] pinctrl: bcm: ns: Use uintptr_t for casting data
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Fix up a compiler error on 64bit architectures where pointers
-and integers differ in size.
-
-Suggested-by: Arnd Bergmann <arnd at arndb.de>
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
----
- drivers/pinctrl/bcm/pinctrl-ns.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/pinctrl/bcm/pinctrl-ns.c
-+++ b/drivers/pinctrl/bcm/pinctrl-ns.c
-@@ -285,7 +285,7 @@ static int ns_pinctrl_probe(struct platf
- 	of_id = of_match_device(ns_pinctrl_of_match_table, dev);
- 	if (!of_id)
- 		return -EINVAL;
--	ns_pinctrl->chipset_flag = (unsigned int)of_id->data;
-+	ns_pinctrl->chipset_flag = (uintptr_t)of_id->data;
- 
- 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
- 					   "cru_gpio_control");
-@@ -307,7 +307,7 @@ static int ns_pinctrl_probe(struct platf
- 	for (i = 0, pin = (struct pinctrl_pin_desc *)&pctldesc->pins[0];
- 	     i < ARRAY_SIZE(ns_pinctrl_pins); i++) {
- 		const struct pinctrl_pin_desc *src = &ns_pinctrl_pins[i];
--		unsigned int chipsets = (unsigned int)src->drv_data;
-+		unsigned int chipsets = (uintptr_t)src->drv_data;
- 
- 		if (chipsets & ns_pinctrl->chipset_flag) {
- 			memcpy(pin++, src, sizeof(*src));
diff --git a/target/linux/bcm53xx/patches-4.14/084-v4.21-pinctrl-bcm-ns-support-updated-DT-binding-as-syscon-.patch b/target/linux/bcm53xx/patches-4.14/084-v4.21-pinctrl-bcm-ns-support-updated-DT-binding-as-syscon-.patch
deleted file mode 100644
index 45595bddc9..0000000000
--- a/target/linux/bcm53xx/patches-4.14/084-v4.21-pinctrl-bcm-ns-support-updated-DT-binding-as-syscon-.patch
+++ /dev/null
@@ -1,99 +0,0 @@
-From a49d784d5a8272d0f63c448fe8dc69e589db006e Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Tue, 18 Dec 2018 16:58:08 +0100
-Subject: [PATCH] pinctrl: bcm: ns: support updated DT binding as syscon
- subnode
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Documentation has been recently updated specifying that pinctrl should
-be subnode of the CRU "syscon". Support that by using parent node for
-regmap and reading "offset" property from the DT.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
-Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
----
- drivers/pinctrl/bcm/pinctrl-ns.c | 29 +++++++++++++++++++----------
- 1 file changed, 19 insertions(+), 10 deletions(-)
-
---- a/drivers/pinctrl/bcm/pinctrl-ns.c
-+++ b/drivers/pinctrl/bcm/pinctrl-ns.c
-@@ -5,6 +5,7 @@
- 
- #include <linux/err.h>
- #include <linux/io.h>
-+#include <linux/mfd/syscon.h>
- #include <linux/module.h>
- #include <linux/of.h>
- #include <linux/of_device.h>
-@@ -12,6 +13,7 @@
- #include <linux/pinctrl/pinctrl.h>
- #include <linux/pinctrl/pinmux.h>
- #include <linux/platform_device.h>
-+#include <linux/regmap.h>
- #include <linux/slab.h>
- 
- #define FLAG_BCM4708		BIT(1)
-@@ -22,7 +24,8 @@ struct ns_pinctrl {
- 	struct device *dev;
- 	unsigned int chipset_flag;
- 	struct pinctrl_dev *pctldev;
--	void __iomem *base;
-+	struct regmap *regmap;
-+	u32 offset;
- 
- 	struct pinctrl_desc pctldesc;
- 	struct ns_pinctrl_group *groups;
-@@ -229,9 +232,9 @@ static int ns_pinctrl_set_mux(struct pin
- 		unset |= BIT(pin_number);
- 	}
- 
--	tmp = readl(ns_pinctrl->base);
-+	regmap_read(ns_pinctrl->regmap, ns_pinctrl->offset, &tmp);
- 	tmp &= ~unset;
--	writel(tmp, ns_pinctrl->base);
-+	regmap_write(ns_pinctrl->regmap, ns_pinctrl->offset, tmp);
- 
- 	return 0;
- }
-@@ -263,13 +266,13 @@ static const struct of_device_id ns_pinc
- static int ns_pinctrl_probe(struct platform_device *pdev)
- {
- 	struct device *dev = &pdev->dev;
-+	struct device_node *np = dev->of_node;
- 	const struct of_device_id *of_id;
- 	struct ns_pinctrl *ns_pinctrl;
- 	struct pinctrl_desc *pctldesc;
- 	struct pinctrl_pin_desc *pin;
- 	struct ns_pinctrl_group *group;
- 	struct ns_pinctrl_function *function;
--	struct resource *res;
- 	int i;
- 
- 	ns_pinctrl = devm_kzalloc(dev, sizeof(*ns_pinctrl), GFP_KERNEL);
-@@ -287,12 +290,18 @@ static int ns_pinctrl_probe(struct platf
- 		return -EINVAL;
- 	ns_pinctrl->chipset_flag = (uintptr_t)of_id->data;
- 
--	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
--					   "cru_gpio_control");
--	ns_pinctrl->base = devm_ioremap_resource(dev, res);
--	if (IS_ERR(ns_pinctrl->base)) {
--		dev_err(dev, "Failed to map pinctrl regs\n");
--		return PTR_ERR(ns_pinctrl->base);
-+	ns_pinctrl->regmap = syscon_node_to_regmap(of_get_parent(np));
-+	if (IS_ERR(ns_pinctrl->regmap)) {
-+		int err = PTR_ERR(ns_pinctrl->regmap);
-+
-+		dev_err(dev, "Failed to map pinctrl regs: %d\n", err);
-+
-+		return err;
-+	}
-+
-+	if (of_property_read_u32(np, "offset", &ns_pinctrl->offset)) {
-+		dev_err(dev, "Failed to get register offset\n");
-+		return -ENOENT;
- 	}
- 
- 	memcpy(pctldesc, &ns_pinctrl_desc, sizeof(*pctldesc));
diff --git a/target/linux/bcm53xx/patches-4.14/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch b/target/linux/bcm53xx/patches-4.14/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch
deleted file mode 100644
index 3320c1e233..0000000000
--- a/target/linux/bcm53xx/patches-4.14/130-ARM-dts-BCM5301X-Add-DT-for-Luxul-XWC-2000.patch
+++ /dev/null
@@ -1,80 +0,0 @@
-From: Dan Haab <dan.haab at legrand.com>
-Date: Wed, 2 Oct 2019 09:57:26 -0600
-Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XWC-2000
-
-It's a simple network device based on BCM47094 with just a single
-Ethernet port.
-
-Signed-off-by: Dan Haab <dan.haab at legrand.com>
----
- arch/arm/boot/dts/Makefile                    |  1 +
- arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts | 53 +++++++++++++++++++
- 2 files changed, 54 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -105,6 +105,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm47094-luxul-abr-4500.dtb \
- 	bcm47094-luxul-xap-1610.dtb \
- 	bcm47094-luxul-xbr-4500.dtb \
-+	bcm47094-luxul-xwc-2000.dtb \
- 	bcm47094-luxul-xwr-3100.dtb \
- 	bcm47094-luxul-xwr-3150-v1.dtb \
- 	bcm47094-netgear-r8500.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
-@@ -0,0 +1,53 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright 2019 Legrand AV Inc.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm47094.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+
-+/ {
-+	compatible = "luxul,xwc-2000-v1", "brcm,bcm47094", "brcm,bcm4708";
-+	model = "Luxul XWC-2000 V1";
-+
-+	chosen {
-+		bootargs = "earlycon";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000
-+		       0x88000000 0x18000000>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		status	{
-+			label = "bcm53xx:green:status";
-+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "timer";
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		restart {
-+			label = "Reset";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+};
-+
-+&uart1 {
-+	status = "okay";
-+};
-+
-+&spi_nor {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/180-usb-xhci-add-support-for-performing-fake-doorbell.patch b/target/linux/bcm53xx/patches-4.14/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
deleted file mode 100644
index 5784f5e5ab..0000000000
--- a/target/linux/bcm53xx/patches-4.14/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
+++ /dev/null
@@ -1,137 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Sat, 1 Oct 2016 22:54:48 +0200
-Subject: [PATCH] usb: xhci: add support for performing fake doorbell
-
-Broadcom's Northstar XHCI controllers seem to need a special start
-procedure to work correctly. There isn't any official documentation of
-this, the problem is that controller doesn't detect any connected
-devices with default setup. Moreover connecting USB device to controller
-that doesn't run properly can cause SoC's watchdog issues.
-
-A workaround that was successfully tested on multiple devices is to
-perform a fake doorbell. This patch adds code for doing this and enables
-it on BCM4708 family.
----
- drivers/usb/host/xhci-plat.c |  6 +++++
- drivers/usb/host/xhci.c      | 63 +++++++++++++++++++++++++++++++++++++++++---
- drivers/usb/host/xhci.h      |  1 +
- 3 files changed, 67 insertions(+), 3 deletions(-)
-
---- a/drivers/usb/host/xhci-plat.c
-+++ b/drivers/usb/host/xhci-plat.c
-@@ -67,12 +67,18 @@ static int xhci_priv_resume_quirk(struct
- 
- static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci)
- {
-+	struct platform_device	*pdev = to_platform_device(dev);
-+	struct device_node	*node = pdev->dev.of_node;
-+
- 	/*
- 	 * As of now platform drivers don't provide MSI support so we ensure
- 	 * here that the generic code does not try to make a pci_dev from our
- 	 * dev struct in order to setup MSI
- 	 */
- 	xhci->quirks |= XHCI_PLAT;
-+
-+	if (node && of_machine_is_compatible("brcm,bcm4708"))
-+		xhci->quirks |= XHCI_FAKE_DOORBELL;
- }
- 
- /* called during probe() after chip reset completes */
---- a/drivers/usb/host/xhci.c
-+++ b/drivers/usb/host/xhci.c
-@@ -166,6 +166,49 @@ int xhci_start(struct xhci_hcd *xhci)
- 	return ret;
- }
- 
-+/**
-+ * xhci_fake_doorbell - Perform a fake doorbell on a specified slot
-+ *
-+ * Some controllers require a fake doorbell to start correctly. Without that
-+ * they simply don't detect any devices.
-+ */
-+static int xhci_fake_doorbell(struct xhci_hcd *xhci, int slot_id)
-+{
-+	u32 temp;
-+
-+	/* Alloc a virt device for that slot */
-+	if (!xhci_alloc_virt_device(xhci, slot_id, NULL, GFP_NOIO)) {
-+		xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n");
-+		return -ENOMEM;
-+	}
-+
-+	/* Ring fake doorbell for slot_id ep 0 */
-+	xhci_ring_ep_doorbell(xhci, slot_id, 0, 0);
-+	usleep_range(1000, 1500);
-+
-+	/* Read the status to check if HSE is set or not */
-+	temp = readl(&xhci->op_regs->status);
-+
-+	/* Clear HSE if set */
-+	if (temp & STS_FATAL) {
-+		xhci_dbg(xhci, "HSE problem detected, status: 0x%08x\n", temp);
-+		temp &= ~0x1fff;
-+		temp |= STS_FATAL;
-+		writel(temp, &xhci->op_regs->status);
-+		usleep_range(1000, 1500);
-+		readl(&xhci->op_regs->status);
-+	}
-+
-+	/* Free virt device */
-+	xhci_free_virt_device(xhci, slot_id);
-+
-+	/* We're done if controller is already running */
-+	if (readl(&xhci->op_regs->command) & CMD_RUN)
-+		return 0;
-+
-+	return xhci_start(xhci);
-+}
-+
- /*
-  * Reset a halted HC.
-  *
-@@ -549,10 +592,20 @@ static int xhci_init(struct usb_hcd *hcd
- 
- static int xhci_run_finished(struct xhci_hcd *xhci)
- {
--	if (xhci_start(xhci)) {
--		xhci_halt(xhci);
--		return -ENODEV;
-+	int err;
-+
-+	err = xhci_start(xhci);
-+	if (err) {
-+		err = -ENODEV;
-+		goto err_halt;
- 	}
-+
-+	if (xhci->quirks & XHCI_FAKE_DOORBELL) {
-+		err = xhci_fake_doorbell(xhci, 1);
-+		if (err)
-+			goto err_halt;
-+	}
-+
- 	xhci->shared_hcd->state = HC_STATE_RUNNING;
- 	xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
- 
-@@ -562,6 +615,10 @@ static int xhci_run_finished(struct xhci
- 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- 			"Finished xhci_run for USB3 roothub");
- 	return 0;
-+
-+err_halt:
-+	xhci_halt(xhci);
-+	return err;
- }
- 
- /*
---- a/drivers/usb/host/xhci.h
-+++ b/drivers/usb/host/xhci.h
-@@ -1840,6 +1840,7 @@ struct xhci_hcd {
- #define XHCI_INTEL_USB_ROLE_SW	BIT_ULL(31)
- #define XHCI_RESET_PLL_ON_DISCONNECT	BIT_ULL(34)
- #define XHCI_SNPS_BROKEN_SUSPEND    BIT_ULL(35)
-+#define XHCI_FAKE_DOORBELL	BIT_ULL(36)
- 
- 	unsigned int		num_active_eps;
- 	unsigned int		limit_active_eps;
diff --git a/target/linux/bcm53xx/patches-4.14/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch b/target/linux/bcm53xx/patches-4.14/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch
deleted file mode 100644
index ef91db9014..0000000000
--- a/target/linux/bcm53xx/patches-4.14/300-ARM-BCM5301X-Disable-MMU-and-Dcache-during-decompres.patch
+++ /dev/null
@@ -1,101 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Wed, 24 Sep 2014 22:14:07 +0200
-Subject: [PATCH] ARM: BCM5301X: Disable MMU and Dcache during decompression
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Broadcom devices have broken CFE (bootloader) that leaves hardware in an
-invalid state. It causes problems with booting Linux. On Northstar
-devices kernel was randomly hanging in ~25% of tries during early init.
-Hangs used to happen at random places in the start_kernel. On BCM53573
-kernel doesn't even seem to start booting.
-
-To workaround this problem we need to do following very early:
-1) Clear 2 following bits in the SCTLR register:
-#define CR_M    (1 << 0)        /* MMU enable */
-#define CR_C    (1 << 2)        /* Dcache enable */
-2) Flush the whole D-cache
-3) Disable L2 cache
-
-Unfortunately this patch is not upstreamable as it does above things
-unconditionally. We can't check if we are running on Broadcom platform
-in any safe way and doing such hacks with ARCH_MULTI_V7 is unacceptable
-as it could break other devices support.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
----
-
---- a/arch/arm/boot/compressed/Makefile
-+++ b/arch/arm/boot/compressed/Makefile
-@@ -32,6 +32,11 @@ ifeq ($(CONFIG_ARCH_ACORN),y)
- OBJS		+= ll_char_wr.o font.o
- endif
- 
-+ifeq ($(CONFIG_ARCH_BCM_5301X),y)
-+OBJS		+= head-bcm_5301x-mpcore.o
-+OBJS		+= cache-v7-min.o
-+endif
-+
- ifeq ($(CONFIG_ARCH_SA1100),y)
- OBJS		+= head-sa1100.o
- endif
---- /dev/null
-+++ b/arch/arm/boot/compressed/head-bcm_5301x-mpcore.S
-@@ -0,0 +1,37 @@
-+/*
-+ *
-+ * Platform specific tweaks.  This is merged into head.S by the linker.
-+ *
-+ */
-+
-+#include <linux/linkage.h>
-+#include <asm/assembler.h>
-+#include <asm/cp15.h>
-+
-+		.section        ".start", "ax"
-+
-+/*
-+ * This code section is spliced into the head code by the linker
-+ */
-+
-+__plat_uncompress_start:
-+
-+	@ Preserve r8/r7 i.e. kernel entry values
-+	mov	r12, r8
-+
-+	@ Clear MMU enable and Dcache enable bits
-+	mrc	p15, 0, r0, c1, c0, 0		@ Read SCTLR
-+	bic	r0, #CR_C|CR_M
-+	mcr	p15, 0, r0, c1, c0, 0		@ Write SCTLR
-+	nop
-+
-+	@ Call the cache invalidation routine
-+	bl	v7_flush_dcache_all
-+	nop
-+	mov	r0,#0
-+	ldr	r3, =0x19022000			@ L2 cache controller, control reg
-+	str	r0, [r3, #0x100]		@ Disable L2 cache
-+	nop
-+
-+	@ Restore
-+	mov	r8, r12
---- a/arch/arm/boot/compressed/cache-v7-min.S
-+++ b/arch/arm/boot/compressed/cache-v7-min.S
-@@ -12,6 +12,7 @@
- 
- #include <linux/linkage.h>
- #include <linux/init.h>
-+#include <asm/assembler.h>
- 
- 	__INIT
- 
-@@ -63,7 +64,7 @@ loop2:
-  ARM(	orr	r11, r11, r9, lsl r2	)	@ factor index number into r11
-  THUMB(	lsl	r6, r9, r2		)
-  THUMB(	orr	r11, r11, r6		)	@ factor index number into r11
--	mcr	p15, 0, r11, c7, c14, 2		@ clean & invalidate by set/way
-+	mcr     p15, 0, r11, c7, c6, 2		@ clean & invalidate by set/way
- 	subs	r9, r9, #1			@ decrement the index
- 	bge	loop2
- 	subs	r4, r4, #1			@ decrement the way
diff --git a/target/linux/bcm53xx/patches-4.14/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch b/target/linux/bcm53xx/patches-4.14/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
deleted file mode 100644
index d1d287588c..0000000000
--- a/target/linux/bcm53xx/patches-4.14/302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Subject: [PATCH] ARM: dts: BCM5301X: Update Northstar pinctrl binding
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
----
-
---- a/arch/arm/boot/dts/bcm5301x.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x.dtsi
-@@ -400,16 +400,12 @@
- 		#size-cells = <1>;
- 
- 		cru at 100 {
--			compatible = "simple-bus";
-+			compatible = "syscon", "simple-mfd";
- 			reg = <0x100 0x1a4>;
--			ranges;
--			#address-cells = <1>;
--			#size-cells = <1>;
- 
--			pin-controller at 1c0 {
-+			pinctrl {
- 				compatible = "brcm,bcm4708-pinmux";
--				reg = <0x1c0 0x24>;
--				reg-names = "cru_gpio_control";
-+				offset = <0xc0>;
- 
- 				spi-pins {
- 					groups = "spi_grp";
diff --git a/target/linux/bcm53xx/patches-4.14/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch b/target/linux/bcm53xx/patches-4.14/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch
deleted file mode 100644
index c546ba9f62..0000000000
--- a/target/linux/bcm53xx/patches-4.14/310-ARM-BCM5301X-Add-DT-for-Netgear-R7900.patch
+++ /dev/null
@@ -1,64 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5 at gmail.com>
-Subject: [PATCH] ARM: BCM5301X: Add DT for Netgear R7900
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Rafał Miłecki <zajec5 at gmail.com>
----
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -98,6 +98,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
- 	bcm4709-buffalo-wxr-1900dhp.dtb \
- 	bcm4709-linksys-ea9200.dtb \
- 	bcm4709-netgear-r7000.dtb \
-+	bcm4709-netgear-r7900.dtb \
- 	bcm4709-netgear-r8000.dtb \
- 	bcm4709-tplink-archer-c9-v1.dtb \
- 	bcm47094-dlink-dir-885l.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm4709-netgear-r7900.dts
-@@ -0,0 +1,42 @@
-+/*
-+ * Broadcom BCM470X / BCM5301X ARM platform code.
-+ * DTS for Netgear R7900
-+ *
-+ * Copyright (C) 2016 Rafał Miłecki <zajec5 at gmail.com>
-+ *
-+ * Licensed under the GNU/GPL. See COPYING for details.
-+ */
-+
-+/dts-v1/;
-+
-+#include "bcm4709.dtsi"
-+#include "bcm5301x-nand-cs0-bch8.dtsi"
-+
-+/ {
-+	compatible = "netgear,r7900", "brcm,bcm4709", "brcm,bcm4708";
-+	model = "Netgear R7900";
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200";
-+	};
-+
-+	memory {
-+		reg = <0x00000000 0x08000000
-+		       0x88000000 0x08000000>;
-+	};
-+
-+	axi at 18000000 {
-+		usb3 at 23000 {
-+			reg = <0x00023000 0x1000>;
-+
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
diff --git a/target/linux/bcm53xx/patches-4.14/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch b/target/linux/bcm53xx/patches-4.14/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch
deleted file mode 100644
index 5ebc7f89f2..0000000000
--- a/target/linux/bcm53xx/patches-4.14/311-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From: Felix Fietkau <nbd at nbd.name>
-Subject: [PATCH] ARM: BCM5301X: Add power button for Buffalo WZR-1750DHP
-
-Signed-off-by: Felix Fietkau <nbd at nbd.name>
----
---- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
-+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
-@@ -101,6 +101,12 @@
- 		#address-cells = <1>;
- 		#size-cells = <0>;
- 
-+		power {
-+			label = "Power";
-+			linux,code = <KEY_POWER>;
-+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
-+		};
-+
- 		restart {
- 			label = "Reset";
- 			linux,code = <KEY_RESTART>;
diff --git a/target/linux/bcm53xx/patches-4.14/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch b/target/linux/bcm53xx/patches-4.14/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch
deleted file mode 100644
index 742f9265b1..0000000000
--- a/target/linux/bcm53xx/patches-4.14/320-ARM-dts-BCM5301X-Add-serial-to-the-bootargs.patch
+++ /dev/null
@@ -1,116 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Subject: [PATCH] ARM: dts: BCM5301X: Add serial= to the bootargs
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-It's enough to have proper stdout-path for getting serial working but
-for some reason LEDE doesn't offer "Please press Enter to activate this
-console." unless ttyS0 is specified.
-
-This is a workaround to get serial working in LEDE.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
----
-
---- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-+++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
-@@ -12,7 +12,7 @@
- 	model = "TP-LINK Archer C5 V2";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
-@@ -13,7 +13,7 @@
- 	model = "Luxul ABR-4500 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
-@@ -13,7 +13,7 @@
- 	model = "Luxul XBR-4500 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
-+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
-@@ -12,7 +12,7 @@
- 	model = "Luxul XAP-1440 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
-+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
-@@ -12,7 +12,7 @@
- 	model = "Luxul XAP-810 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
-@@ -12,7 +12,7 @@
- 	model = "Luxul XAP-1610 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
-@@ -13,7 +13,7 @@
- 	model = "Luxul XWR-3150 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
---- a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
-+++ b/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
-@@ -13,6 +13,10 @@
- 	compatible = "phicomm,k3", "brcm,bcm47094", "brcm,bcm4708";
- 	model = "Phicomm K3";
- 
-+	chosen {
-+		bootargs = "console=ttyS0,115200";
-+	};
-+
- 	memory {
- 		reg = <0x00000000 0x08000000
- 		       0x88000000 0x18000000>;
---- a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
-+++ b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
-@@ -13,7 +13,7 @@
- 	model = "Luxul XWC-2000 V1";
- 
- 	chosen {
--		bootargs = "earlycon";
-+		bootargs = "console=ttyS0,115200 earlycon";
- 	};
- 
- 	memory {
diff --git a/target/linux/bcm53xx/patches-4.14/321-ARM-dts-BCM5301X-Describe-partition-formats.patch b/target/linux/bcm53xx/patches-4.14/321-ARM-dts-BCM5301X-Describe-partition-formats.patch
deleted file mode 100644
index 66ae6dca33..0000000000
--- a/target/linux/bcm53xx/patches-4.14/321-ARM-dts-BCM5301X-Describe-partition-formats.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 7166207bd1d8c46d09d640d46afc685df9bb9083 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Thu, 22 Nov 2018 09:21:49 +0100
-Subject: [PATCH] ARM: dts: BCM5301X: Describe partition formats
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-It's needed by OpenWrt for custom partitioning.
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
----
- arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
-@@ -34,6 +34,7 @@
- 				partition at 0 {
- 					label = "firmware";
- 					reg = <0x00000000 0x08000000>;
-+					compatible = "seama";
- 				};
- 			};
- 		};
diff --git a/target/linux/bcm53xx/patches-4.14/400-mtd-spi-nor-detect-JEDEC-incompatible-w25q128-using-.patch b/target/linux/bcm53xx/patches-4.14/400-mtd-spi-nor-detect-JEDEC-incompatible-w25q128-using-.patch
deleted file mode 100644
index 446ba6cdcd..0000000000
--- a/target/linux/bcm53xx/patches-4.14/400-mtd-spi-nor-detect-JEDEC-incompatible-w25q128-using-.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5 at gmail.com>
-Subject: [PATCH] mtd: spi-nor: detect JEDEC incompatible w25q128 using 0x90
- command
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Some w25q128 chipsets don't support RDID (0x9f) command, they reply with
-0xff-s only. To suppose such flashes fallback to the 0x90 command.
-
-Signed-off-by: Rafał Miłecki <zajec5 at gmail.com>
----
-
---- a/drivers/mtd/spi-nor/spi-nor.c
-+++ b/drivers/mtd/spi-nor/spi-nor.c
-@@ -1230,6 +1230,18 @@ static const struct flash_info *spi_nor_
- 	}
- 	dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
- 		id[0], id[1], id[2]);
-+
-+	tmp = nor->read_reg(nor, 0x90, id, SPI_NOR_MAX_ID_LEN);
-+	if (tmp < 0) {
-+		dev_dbg(nor->dev, " error %d reading JEDEC ID\n", tmp);
-+		return ERR_PTR(tmp);
-+	}
-+	dev_info(nor->dev, "using Read Manufacturer / Device ID command (0x%02x) returned %02x %02x\n",
-+		 0x90, id[0x03], id[0x04]);
-+	if (id[0x03] == 0xef && id[0x04] == 0x17) {
-+		return spi_nor_match_id("w25q128");
-+	}
-+
- 	return ERR_PTR(-ENODEV);
- }
- 
diff --git a/target/linux/bcm53xx/patches-4.14/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch b/target/linux/bcm53xx/patches-4.14/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch
deleted file mode 100644
index a86f4a8406..0000000000
--- a/target/linux/bcm53xx/patches-4.14/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch
+++ /dev/null
@@ -1,59 +0,0 @@
-From 2a2af518266a29323cf30c3f9ba9ef2ceb1dd84b Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5 at gmail.com>
-Date: Thu, 16 Oct 2014 20:52:16 +0200
-Subject: [PATCH] UBI: Detect EOF mark and erase all remaining blocks
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Rafał Miłecki <zajec5 at gmail.com>
----
- drivers/mtd/ubi/attach.c | 5 +++++
- drivers/mtd/ubi/io.c     | 4 ++++
- drivers/mtd/ubi/ubi.h    | 1 +
- 3 files changed, 10 insertions(+)
-
---- a/drivers/mtd/ubi/attach.c
-+++ b/drivers/mtd/ubi/attach.c
-@@ -95,6 +95,9 @@ static int self_check_ai(struct ubi_devi
- #define AV_ADD		BIT(1)
- #define AV_FIND_OR_ADD	(AV_FIND | AV_ADD)
- 
-+/* Set on finding block with 0xdeadc0de, indicates erasing all blocks behind */
-+bool erase_all_next;
-+
- /**
-  * find_or_add_av - internal function to find a volume, add a volume or do
-  *		    both (find and add if missing).
-@@ -1592,6 +1595,8 @@ int ubi_attach(struct ubi_device *ubi, i
- 	if (!ai)
- 		return -ENOMEM;
- 
-+	erase_all_next = false;
-+
- #ifdef CONFIG_MTD_UBI_FASTMAP
- 	/* On small flash devices we disable fastmap in any case. */
- 	if ((int)mtd_div_by_eb(ubi->mtd->size, ubi->mtd) <= UBI_FM_MAX_START) {
---- a/drivers/mtd/ubi/io.c
-+++ b/drivers/mtd/ubi/io.c
-@@ -759,6 +759,10 @@ int ubi_io_read_ec_hdr(struct ubi_device
- 	}
- 
- 	magic = be32_to_cpu(ec_hdr->magic);
-+	if (magic == 0xdeadc0de)
-+		erase_all_next = true;
-+	if (erase_all_next)
-+		return read_err ? UBI_IO_FF_BITFLIPS : UBI_IO_FF;
- 	if (magic != UBI_EC_HDR_MAGIC) {
- 		if (mtd_is_eccerr(read_err))
- 			return UBI_IO_BAD_HDR_EBADMSG;
---- a/drivers/mtd/ubi/ubi.h
-+++ b/drivers/mtd/ubi/ubi.h
-@@ -829,6 +829,7 @@ extern struct mutex ubi_devices_mutex;
- extern struct blocking_notifier_head ubi_notifiers;
- 
- /* attach.c */
-+extern bool erase_all_next;
- struct ubi_ainf_peb *ubi_alloc_aeb(struct ubi_attach_info *ai, int pnum,
- 				   int ec);
- void ubi_free_aeb(struct ubi_attach_info *ai, struct ubi_ainf_peb *aeb);
diff --git a/target/linux/bcm53xx/patches-4.14/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch b/target/linux/bcm53xx/patches-4.14/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch
deleted file mode 100644
index 91bb4fae11..0000000000
--- a/target/linux/bcm53xx/patches-4.14/700-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch
+++ /dev/null
@@ -1,52 +0,0 @@
-From 4abdde3ad6bc0b3b157c4bf6ec0bf139d11d07e8 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5 at gmail.com>
-Date: Wed, 13 May 2015 14:13:28 +0200
-Subject: [PATCH] b53: add hacky CPU port fixes for devices not using port 5
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Rafał Miłecki <zajec5 at gmail.com>
----
- drivers/net/phy/b53/b53_common.c | 6 ++++++
- 1 file changed, 6 insertions(+)
-
---- a/drivers/net/phy/b53/b53_common.c
-+++ b/drivers/net/phy/b53/b53_common.c
-@@ -28,6 +28,7 @@
- #include <linux/of.h>
- #include <linux/of_net.h>
- #include <linux/platform_data/b53.h>
-+#include <linux/of.h>
- 
- #include "b53_regs.h"
- #include "b53_priv.h"
-@@ -1579,6 +1580,28 @@ static int b53_switch_init(struct b53_de
- 			return ret;
- 	}
- 
-+	/* Set correct CPU port */
-+	if (of_machine_is_compatible("asus,rt-ac87u"))
-+		sw_dev->cpu_port = 7;
-+	else if (of_machine_is_compatible("netgear,r7900"))
-+		sw_dev->cpu_port = 8;
-+	else if (of_machine_is_compatible("netgear,r8000"))
-+		sw_dev->cpu_port = 8;
-+	else if (of_machine_is_compatible("netgear,r8500"))
-+		sw_dev->cpu_port = 8;
-+
-+	/* Enable extra ports */
-+	if (of_machine_is_compatible("tenda,ac9"))
-+		dev->enabled_ports |= BIT(5);
-+
-+	/*
-+	 * Workaround for devices using port 8 (connected to the 3rd iface).
-+	 * For some reason it doesn't work (no packets on eth2).
-+	 */
-+	if (of_machine_is_compatible("netgear,r7900") ||
-+	    of_machine_is_compatible("netgear,r8000"))
-+		sw_dev->cpu_port = 5;
-+
- 	dev->enabled_ports |= BIT(sw_dev->cpu_port);
- 	sw_dev->ports = fls(dev->enabled_ports);
- 
diff --git a/target/linux/bcm53xx/patches-4.14/905-BCM53573-minor-hacks.patch b/target/linux/bcm53xx/patches-4.14/905-BCM53573-minor-hacks.patch
deleted file mode 100644
index 39f4cf7662..0000000000
--- a/target/linux/bcm53xx/patches-4.14/905-BCM53573-minor-hacks.patch
+++ /dev/null
@@ -1,80 +0,0 @@
-From 6f1c62440eb6846cb8045d7a5480ec7bbe47c96f Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
-Date: Mon, 15 Aug 2016 10:30:41 +0200
-Subject: [PATCH] BCM53573 minor hacks
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
----
-
---- a/arch/arm/boot/dts/bcm53573.dtsi
-+++ b/arch/arm/boot/dts/bcm53573.dtsi
-@@ -53,6 +53,7 @@
- 			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
- 			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
- 			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
-+		clocks = <&ilp>;
- 	};
- 
- 	clocks {
---- a/drivers/bcma/main.c
-+++ b/drivers/bcma/main.c
-@@ -326,14 +326,6 @@ static int bcma_register_devices(struct
- 	}
- #endif
- 
--#ifdef CONFIG_BCMA_SFLASH
--	if (bus->drv_cc.sflash.present) {
--		err = platform_device_register(&bcma_sflash_dev);
--		if (err)
--			bcma_err(bus, "Error registering serial flash\n");
--	}
--#endif
--
- #ifdef CONFIG_BCMA_NFLASH
- 	if (bus->drv_cc.nflash.present) {
- 		err = platform_device_register(&bcma_nflash_dev);
-@@ -411,6 +403,14 @@ int bcma_bus_register(struct bcma_bus *b
- 			bcma_register_core(bus, core);
- 	}
- 
-+#ifdef CONFIG_BCMA_SFLASH
-+	if (bus->drv_cc.sflash.present) {
-+		err = platform_device_register(&bcma_sflash_dev);
-+		if (err)
-+			bcma_err(bus, "Error registering serial flash\n");
-+	}
-+#endif
-+
- 	/* Try to get SPROM */
- 	err = bcma_sprom_get(bus);
- 	if (err == -ENOENT) {
---- a/drivers/clocksource/arm_arch_timer.c
-+++ b/drivers/clocksource/arm_arch_timer.c
-@@ -17,6 +17,7 @@
- #include <linux/smp.h>
- #include <linux/cpu.h>
- #include <linux/cpu_pm.h>
-+#include <linux/clk.h>
- #include <linux/clockchips.h>
- #include <linux/clocksource.h>
- #include <linux/interrupt.h>
-@@ -836,6 +837,16 @@ static void arch_timer_of_configure_rate
- 	if (of_property_read_u32(np, "clock-frequency", &arch_timer_rate))
- 		arch_timer_rate = rate;
- 
-+	/* Get clk rate through clk driver if present */
-+	if (!arch_timer_rate) {
-+		struct clk *clk = of_clk_get(np, 0);
-+
-+		if (!IS_ERR(clk)) {
-+			if (!clk_prepare_enable(clk))
-+				arch_timer_rate = clk_get_rate(clk);
-+		}
-+	}
-+
- 	/* Check the timer frequency. */
- 	if (arch_timer_rate == 0)
- 		pr_warn("frequency not available\n");
-- 
2.20.1


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list