[OpenWrt-Devel] [PATCH] mvebu: add support for Buffalo LinkStation LS421DE
Daniel Gonzalez Cabanelas
dgcbueu at gmail.com
Wed Mar 25 21:00:24 EDT 2020
Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370
Hardware:
SoC: Marvell 88F6707-A1
CPU: Cortex-A9 1200 MHz, 1 core
Flash: SPI-NOR 1 MiB, NAND 512 MiB
RAM: DDR3 512 MiB
Ethernet: 1x 10/100/1000 Mbps
USB: 1x 2.0, 1x 3.0
SATA: 2x 3.0 Gbps
LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
RTC: Ricoh RS5C372A, I2C, no battery
Flash instruction (UART+TFTP):
1. Downgrade the OEM firmware to 1.34 (BUFFALO_BOOTVER=0.13)
2. Boot the Openwrt initramfs image using the serial console:
tftpboot buffalo_ls421de-initramfs-kernel.bin;bootm
3. Flash the sysupgrade image using the Openwrt console:
sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
5. Wait until it finish, the device will reboot with Openwrt installed
on the NAND flash.
Note:
- Device shuting down doesn't work, even if the power slide switch is
used. We must first, via MDIO, set the unused LED2 at the ethernet
phy0 to off state.
Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
---
.../base-files/lib/preinit/06_set_iface_mac | 4 +
.../base-files/lib/upgrade/platform.sh | 3 +
.../boot/dts/armada-370-buffalo-ls421de.dts | 364 ++++++++++++++++++
target/linux/mvebu/image/Makefile | 14 +
target/linux/mvebu/image/cortexa9.mk | 21 +
.../250-buffalo_ls421de-build_dtb.patch | 10 +
6 files changed, 416 insertions(+)
create mode 100644 target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
create mode 100644 target/linux/mvebu/patches-4.19/250-buffalo_ls421de-build_dtb.patch
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac b/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
index fd41836c8d..62ce2653a0 100644
--- a/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
+++ b/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
@@ -9,6 +9,10 @@ preinit_set_mac_address() {
. /lib/functions.sh
case $(board_name) in
+ buffalo,ls421de)
+ mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
+ ip link set dev eth0 address $mac 2>/dev/null
+ ;;
linksys,caiman|linksys,cobra|linksys,rango|linksys,shelby|linksys,venom)
# rename interfaces back to the way they were with 4.4
case "$(readlink /sys/class/net/eth0)" in
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
index 8baed969a3..63042b1535 100755
--- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
@@ -22,6 +22,9 @@ platform_check_image() {
platform_do_upgrade() {
case "$(board_name)" in
+ buffalo,ls421de)
+ nand_do_upgrade "$1"
+ ;;
cznic,turris-omnia|\
solidrun,clearfog-base-a1|\
solidrun,clearfog-pro-a1)
diff --git a/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts b/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
new file mode 100644
index 0000000000..ca161964a4
--- /dev/null
+++ b/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Buffalo LinkStation LS421DE
+ *
+ * Copyright (C) 2020 Daniel González Cabanelas <dgcbueu at gmail.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-370.dtsi"
+#include "mvebu-linkstation-fan.dtsi"
+
+/ {
+ model = "Buffalo LinkStation LS421DE";
+ compatible = "buffalo,ls421de", "marvell,armada370", "marvell,armada-370-xp";
+
+ aliases {
+ led-boot = &led_boot;
+ led-failsafe = &led_failsafe;
+ led-running = &led_power;
+ led-upgrade = &led_upgrade;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk noinitrd rootfstype=squashfs";
+ append-rootblock = "nullparameter="; /* override the bootloader args */
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+
+ internal-regs {
+ rtc at 10300 {
+ status = "disabled";
+ };
+
+ serial at 12000 {
+ status = "okay";
+ };
+
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ ethernet at 74000 {
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins2>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ broken-cd;
+ };
+
+ usb at 50000 {
+ vcc-supply = <&usb_v5_regulator>;
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ clock-frequency = <100000>;
+ status = "okay";
+
+ rs5c372a: rs5c372a at 32 {
+ compatible = "ricoh,rs5c372a";
+ reg = <0x32>;
+ };
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power_usb &pmx_power_hdd1 &pmx_power_hdd2>;
+
+ pinctrl-names = "default";
+
+ usb_v5_regulator: usb-v5-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "USB";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <4000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ ata1_regulator: ata1-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "HDD1";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ startup-delay-us = <2000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ ata2_regulator: ata2-regulator {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "HDD2";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ startup-delay-us = <4000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_hdd_present &pmx_buttons>;
+ pinctrl-names = "default";
+
+ hdd1-present {
+ label = "HDD1 Present";
+ linux,code = <KEY_PROG1>;
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ };
+
+ hdd2-present {
+ label = "HDD2 Present";
+ linux,code = <KEY_PROG2>;
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+
+ };
+
+ power {
+ label = "Power Switch";
+ linux,code = <KEY_POWER>;
+ linux,input-type = <EV_SW>;
+ gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+
+ function {
+ label = "Function Button";
+ linux,code = <KEY_OPTION>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+
+ system_red {
+ label = "ls421de:red:system";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_power: power_white {
+ label = "ls421de:white:power";
+ gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ led_failsafe: power_red {
+ label = "ls421de:red:power";
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_upgrade: power_orange {
+ label = "ls421de:orange:power";
+ gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_boot: system_white {
+ label = "ls421de:white:system";
+ gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ hdd1_red {
+ label = "ls421de:red:hdd1";
+ gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-activity";
+ };
+
+ hdd2_red {
+ label = "ls421de:red:hdd2";
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ /* FIXME: this driver needs to be aware of the LED2 eth phy use,
+ which must be set to off state before shutting down the machine */
+ restart_poweroff {
+ compatible = "restart-poweroff";
+ };
+
+ gpio_fan {
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH
+ &gpio0 14 GPIO_ACTIVE_HIGH>;
+
+ alarm-gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&pinctrl {
+ pmx_power_usb: pmx-power-usb {
+ marvell,pins = "mpp5";
+ marvell,function = "gpo";
+ };
+ pmx_power_hdd1: pmx-power-hdd1 {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+ pmx_power_hdd2: pmx-power-hdd2 {
+ marvell,pins = "mpp9";
+ marvell,function = "gpo";
+ };
+ pmx_fan_lock: pmx-fan-lock {
+ marvell,pins = "mpp10";
+ marvell,function = "gpio";
+ };
+ pmx_hdd_present: pmx-hdd-present {
+ marvell,pins = "mpp11", "mpp12";
+ marvell,function = "gpio";
+ };
+ pmx_fan_high: pmx-fan-high {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+ pmx_fan_low: pmx-fan-low {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp15", "mpp16";
+ marvell,function = "gpio";
+ };
+ pmx_leds1: pmx-leds {
+ marvell,pins = "mpp7", "mpp54", "mpp59", "mpp61";
+ marvell,function = "gpo";
+ };
+ pmx_leds2: pmx-leds {
+ marvell,pins = "mpp55", "mpp57", "mpp62";
+ marvell,function = "gpio";
+ };
+};
+
+&pciec {
+ status = "okay";
+ /* Connected to uPD720202 USB 3.0 Host */
+ pcie at 1,0 {
+ status = "okay";
+ };
+ /* Unpopulated miniPCIe slot */
+ pcie at 2,0 {
+ status = "disabled";
+ };
+};
+
+&mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy at 0 { /* Marvell 88E1518 */
+ reg = <0>;
+ /* LED2 is used to inform uBoot if the power-switch was slided to
+ the "off" position, and then shutdown the machine.
+ Page 0x3, Register 0x10, bit 8:
+ 0x800: LED2 off, shutdown the machine
+ 0x900: LED2 on, boot the machine */
+ marvell,reg-init = <0x3 0x10 0x1 0x1991>, /* LED Function */
+ <0x3 0x11 0x1 0x4401>, /* LED polarity */
+ <0x3 0x12 0x1 0x4905>; /* LED Timer */
+ };
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
+ marvell,nand-keep-config;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "kernel";
+ reg = <0x00000000 0x02000000>; /* 32 MiB */
+ };
+
+ partition at 2000000 {
+ label = "ubi";
+ reg = <0x02000000 0x1e000000>; /* 480 MiB */
+ };
+
+ nand_flash at 0 {
+ label = "nand_all";
+ reg = <0 0>; /* full flash */
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-0 = <&spi0_pins2>;
+ pinctrl-names = "default";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mxicy,mx25l8005", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ reg = <0x00000 0xf0000>; /* 960 KiB*/
+ label = "u-boot";
+ read-only;
+ };
+ partition at f0000 {
+ reg = <0xf0000 0x10000>; /* 64 KiB */
+ label = "u-boot-env";
+ };
+ };
+ };
+};
diff --git a/target/linux/mvebu/image/Makefile b/target/linux/mvebu/image/Makefile
index ef9274866d..3a47878069 100644
--- a/target/linux/mvebu/image/Makefile
+++ b/target/linux/mvebu/image/Makefile
@@ -40,6 +40,20 @@ define Build/boot-img-ext4
make_ext4fs -J -L kernel -l $(CONFIG_TARGET_KERNEL_PARTSIZE)M $@.bootimg $@.boot
endef
+define Build/buffalo-kernel-jffs2
+ rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
+ mkdir -p $(KDIR)/kernel_jffs2
+ dd if=/dev/zero of=$@.fakerd bs=131008 count=1 conv=sync
+ $(STAGING_DIR_HOST)/bin/mkimage \
+ -T ramdisk -A $(LINUX_KARCH) -O linux -C gzip -n 'fake initrd' \
+ -d $@.fakerd $(KDIR)/kernel_jffs2/initrd.buffalo
+ cp $@ $(KDIR)/kernel_jffs2/uImage.buffalo
+ $(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
+ --little-endian -v --squash-uids -q -f -n -x lzma -x rtime -m none \
+ --eraseblock=128KiB --pad=$(KERNEL_SIZE) -d $(KDIR)/kernel_jffs2 -o $@
+ rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
+endef
+
define Build/sdcard-img
SIGNATURE="$(IMG_PART_SIGNATURE)" \
./gen_mvebu_sdcard_img.sh $@ \
diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
index 85bfa94dbd..aa8e31dbdf 100644
--- a/target/linux/mvebu/image/cortexa9.mk
+++ b/target/linux/mvebu/image/cortexa9.mk
@@ -6,6 +6,27 @@
# See /LICENSE for more information.
#
+define Device/buffalo_ls421de
+ $(Device/NAND-128K)
+ DEVICE_VENDOR := Buffalo
+ DEVICE_MODEL := LinkStation LS421DE
+ UBINIZE_OPTS := -E 5
+ SUBPAGESIZE :=
+ KERNEL_SIZE := 33554432
+ FILESYSTEMS := squashfs ubifs
+ KERNEL := kernel-bin | append-dtb | uImage none | buffalo-kernel-jffs2
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
+ IMAGES := factory.bin sysupgrade.bin
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ DEVICE_DTS := armada-370-buffalo-ls421de
+ SUPPORTED_DEVICES += ls421de
+ DEVICE_PACKAGES := \
+ kmod-rtc-rs5c372a kmod-hwmon-gpiofan kmod-usb2 kmod-usb3 kmod-usb-storage \
+ kmod-ata-core kmod-ata-marvell-sata kmod-fs-f2fs kmod-fs-ext4 kmod-fs-vfat \
+ kmod-fs-xfs kmod-nls-cp437 kmod-nls-iso8859-1 mkf2fs e2fsprogs partx-utils
+endef
+ TARGET_DEVICES += buffalo_ls421de
+
define Device/cznic_turris-omnia
DEVICE_VENDOR := CZ.NIC
DEVICE_MODEL := Turris Omnia
diff --git a/target/linux/mvebu/patches-4.19/250-buffalo_ls421de-build_dtb.patch b/target/linux/mvebu/patches-4.19/250-buffalo_ls421de-build_dtb.patch
new file mode 100644
index 0000000000..b0f883035d
--- /dev/null
+++ b/target/linux/mvebu/patches-4.19/250-buffalo_ls421de-build_dtb.patch
@@ -0,0 +1,10 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -1135,6 +1135,7 @@
+ zynq-zybo.dtb \
+ zynq-zybo-z7.dtb
+ dtb-$(CONFIG_MACH_ARMADA_370) += \
++ armada-370-buffalo-ls421de.dtb \
+ armada-370-db.dtb \
+ armada-370-dlink-dns327l.dtb \
+ armada-370-mirabox.dtb \
--
2.26.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list