[OpenWrt-Devel] [PATCH 2/2] ath79: rename mikrotik RB 922UAGS-5HPacD mtd partition

[Thibaut VARÈNE]

In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.

This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.

This commit fixes the previous support files.

Signed-off-by: Thibaut VARÈNE <hacks at slashdirt.org>
---
 .../linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts | 6 +++---
 .../ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata  | 2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts
index 26a18ad6a7..3f2a1a51a6 100644
--- a/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts
+++ b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts
@@ -80,7 +80,7 @@
 &eth0 {
 	status = "okay";
 
-	mtd-mac-address = <&art 0x10>;
+	mtd-mac-address = <&hard_config 0x10>;
 	phy-handle = <&phy4>;
 	pll-data = <0x8f000000 0xa0000101 0xa0001313>;
 
@@ -109,8 +109,8 @@
 				read-only;
 			};
 
-			art: partition at c000 {
-				label = "art";
+			hard_config: partition at c000 {
+				label = "hard_config";
 				reg = <0x000c000 0x0001000>;
 				read-only;
 			};
diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8a1bed58c1..31a1db5aeb 100644
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -28,7 +28,7 @@ case "$FIRMWARE" in
 "ath10k/cal-pci-0000:01:00.0.bin")
 	case $board in
 	mikrotik,routerboard-922uags-5hpacd)
-		mikrotik_caldata_extract "art" 0x5000 0x844
+		mikrotik_caldata_extract "hard_config" 0x5000 0x844
 		;;
 	esac
 	;;
-- 
2.11.0


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel