[OpenWrt-Devel] [PATCH 2/2] ramips: fix and tidy up DTS for D-Link DIR-810L

[Adrian Schmutzler]

This patch addresses several issues for D-Link DIR-810L:

- add correct button codes
- harmonize button node names
- use generic flash at 0
- remove unused pin groups from state_default
- improve sorting of properties

The patch is only build-tested.

Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>

---

If somebody owns this device, I'd be delighted about a test of both patches
in general as well as if somebody would test if higher SPI frequency is
possible.

---
 .../ramips/dts/mt7620a_dlink_dir-810l.dts      | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)

diff --git a/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts b/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts
index 0b1ca26ba4..514e9cc354 100644
--- a/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts
+++ b/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts
@@ -23,20 +23,20 @@
 		reset {
 			label = "reset";
 			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
-			linux,code = <BTN_0>;
+			linux,code = <KEY_RESTART>;
 		};
 
 		wps {
 			label = "wps";
 			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
-			linux,code = <BTN_0>;
+			linux,code = <KEY_WPS_BUTTON>;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		led_power_green: power {
+		led_power_green: power_green {
 			label = "dir-810l:green:power";
 			gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
 		};
@@ -46,7 +46,7 @@
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		power2 {
+		power_orange {
 			label = "dir-810l:orange:power";
 			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 		};
@@ -56,7 +56,7 @@
 &spi0 {
 	status = "okay";
 
-	m25p80 at 0 {
+	flash at 0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
@@ -119,7 +119,7 @@
 
 &state_default {
 	gpio {
-		ralink,group = "mdio", "rgmii1", "i2c", "wled", "uartf";
+		ralink,group = "i2c", "uartf";
 		ralink,function = "gpio";
 	};
 };
@@ -130,9 +130,10 @@
 };
 
 &gsw {
-	mediatek,port4 = "ephy";
 	pinctrl-names = "default";
 	pinctrl-0 = <&ephy_pins>;
+
+	mediatek,port4 = "ephy";
 };
 
 &pcie {
@@ -140,9 +141,10 @@
 };
 
 &wmac {
-	ralink,mtd-eeprom = <&factory 0x0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pa_pins>;
+
+	ralink,mtd-eeprom = <&factory 0x0>;
 	mtd-mac-address = <&factory 0x28>;
 };
 
-- 
2.20.1


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel