[OpenWrt-Devel] [PATCH] mvebu: add support for GL.iNet GL-MV1000
Li Zhang
li.zhang at gl-inet.com
Fri Apr 17 02:39:32 EDT 2020
This patch adds supports for GL-MV1000.
Specification:
- SOC: Marvell Armada 88F3720 (1GHz)
- Flash: 16MB (W25Q128FWSIG)
- RAM: 1GB DDR4
- Ethernet: 3x GE (1 WAN + 2 LAN)
- EMMC: 8GB EMMC (KLM8G1GETF-B041)
- MicroSD: 1x microSD slot
- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
- Button: 1x reset button,1x slide switch
- LED: 3x greed LED
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
Update firmware instructions
============================
In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.
Signed-off-by: Li Zhang <li.zhang at gl-inet.com>
---
package/boot/uboot-envtools/files/mvebu | 3 +
.../cortexa53/base-files/etc/board.d/02_network | 3 +-
.../arm64/boot/dts/marvell/armada-gl-mv1000.dts | 165 +++++++++++++++++++++
target/linux/mvebu/image/cortexa53.mk | 9 ++
4 files changed, 179 insertions(+), 1 deletion(-)
create mode 100644 target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts
diff --git a/package/boot/uboot-envtools/files/mvebu b/package/boot/uboot-envtools/files/mvebu
index 7902384..b883f0a 100644
--- a/package/boot/uboot-envtools/files/mvebu
+++ b/package/boot/uboot-envtools/files/mvebu
@@ -24,6 +24,9 @@ globalscale,espressobin-v7-emmc|\
marvell,armada8040-mcbin)
ubootenv_add_uci_config "/dev/mtd0" "0x3f0000" "0x10000" "0x10000" "1"
;;
+glinet,gl-mv1000)
+ ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x8000" "0x8000" "1"
+ ;;
linksys,caiman|\
linksys,cobra|\
linksys,shelby)
diff --git a/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network
index ba4b930..9b1d97d 100755
--- a/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network
@@ -14,7 +14,8 @@ case "$board" in
globalscale,espressobin|\
globalscale,espressobin-emmc|\
globalscale,espressobin-v7|\
-globalscale,espressobin-v7-emmc)
+globalscale,espressobin-v7-emmc|\
+glinet,gl-mv1000)
ucidef_set_interfaces_lan_wan "lan0 lan1" "wan"
;;
marvell,armada-3720-db|\
diff --git a/target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts b/target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts
new file mode 100644
index 0000000..9d7963c
--- /dev/null
+++ b/target/linux/mvebu/files-4.19/arch/arm64/boot/dts/marvell/armada-gl-mv1000.dts
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for GL.iNet GL-MV1000
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+ model = "GL.inet GL-MV1000";
+ compatible = "glinet,gl-mv1000", "marvell,armada3720";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ vcc_sd_reg1: regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vcc_sd1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+
+ gpios-states = <0>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ enable-active-high;
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <104000000>;
+ m25p,fast-read;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0 0xf0000>;
+ };
+
+ partition at f0000 {
+ label = "u-boot-env";
+ reg = <0Xf0000 0x8000>;
+ };
+
+ factory: partition at f8000 {
+ label = "factory";
+ reg = <0xf8000 0x8000>;
+ };
+ };
+ };
+};
+
+&sdhci1 {
+ wp-inverted;
+ bus-width = <4>;
+ cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
+ marvell,pad-type = "sd";
+ no-1-8-v;
+ vqmmc-supply = <&vcc_sd_reg1>;
+ status = "okay";
+};
+
+&sdhci0 {
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ marvell,pad-type = "fixed-1-8v";
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&mdio {
+ switch0: switch0 at 1 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ dsa,member = <0 0>;
+
+ ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <ð0>;
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "wan";
+ phy-handle = <&switch0phy0>;
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan0";
+ phy-handle = <&switch0phy1>;
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan1";
+ phy-handle = <&switch0phy2>;
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy0: switch0phy0 at 11 {
+ reg = <0x11>;
+ };
+ switch0phy1: switch0phy1 at 12 {
+ reg = <0x12>;
+ };
+ switch0phy2: switch0phy2 at 13 {
+ reg = <0x13>;
+ };
+ };
+ };
+};
+
+ð0 {
+ mtd-mac-address = <&factory 0x0>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
diff --git a/target/linux/mvebu/image/cortexa53.mk b/target/linux/mvebu/image/cortexa53.mk
index 77f5c79..1436c1b 100644
--- a/target/linux/mvebu/image/cortexa53.mk
+++ b/target/linux/mvebu/image/cortexa53.mk
@@ -69,3 +69,12 @@ define Device/methode_udpu
BOOT_SCRIPT := udpu
endef
TARGET_DEVICES += methode_udpu
+
+define Device/glinet_gl-mv1000
+ $(call Device/Default-arm64)
+ DEVICE_TITLE := GL.iNet GL-MV1000
+ DEVICE_DTS := armada-gl-mv1000
+ SUPPORTED_DEVICES := glinet,gl-mv1000
+endef
+TARGET_DEVICES += glinet_gl-mv1000
+
--
2.7.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list