[OpenWrt-Devel] [PATCH v5] ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1

Ernst Spielmann endspiel at disroot.org
Thu Apr 16 14:42:29 EDT 2020 

Specifications:

- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)

Flash instructions:

1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.

Signed-off-by: Ernst Spielmann <endspiel at disroot.org>
---
v2: RT-N12 VP *B1* was incorrectly mentioned as *B3* in mt76x8.mk
v3: switch to master branch & split device group into individual entries
v4: add licenses, update DTS(I), move `leds` section to DTS'es, s/_/-/ in boardnames
v5: fix incorrect portmap in DTSI.

 .../linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts  |  34 +++++++
 .../linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts  |  34 +++++++
 .../ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts      |  34 +++++++
 target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi  | 100 +++++++++++++++++++++
 target/linux/ramips/image/mt76x8.mk                |  24 +++++
 .../ramips/mt76x8/base-files/etc/board.d/01_leds   |   6 ++
 .../mt76x8/base-files/etc/board.d/02_network       |  21 +++--
 7 files changed, 244 insertions(+), 9 deletions(-)
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi

diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts b/target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts
new file mode 100644
index 0000000000..eaf5796d28
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "mt7628an_asus_rt-n1x.dtsi"
+
+/ {
+	compatible = "asus,rt-n10p-v3", "mediatek,mt7628an-soc";
+	model = "Asus RT-N10P V3";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n10p-v3:green:power";
+			gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n10p-v3:green:wlan";
+			gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wan {
+			label = "rt-n10p-v3:green:wan";
+			gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n10p-v3:green:lan";
+			gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts b/target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts
new file mode 100644
index 0000000000..46f199f390
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "mt7628an_asus_rt-n1x.dtsi"
+
+/ {
+	compatible = "asus,rt-n11p-b1", "mediatek,mt7628an-soc";
+	model = "Asus RT-N11P B1";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n11p-b1:green:power";
+			gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n11p-b1:green:wlan";
+			gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wan {
+			label = "rt-n11p-b1:green:wan";
+			gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n11p-b1:green:lan";
+			gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts b/target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts
new file mode 100644
index 0000000000..b6070d784f
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "mt7628an_asus_rt-n1x.dtsi"
+
+/ {
+	compatible = "asus,rt-n12-vp-b1", "mediatek,mt7628an-soc";
+	model = "Asus RT-N12 VP B1";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n12-vp-b1:green:power";
+			gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n12-vp-b1:green:wlan";
+			gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wan {
+			label = "rt-n12-vp-b1:green:wan";
+			gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n12-vp-b1:green:lan";
+			gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi b/target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi
new file mode 100644
index 0000000000..860024aa93
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition at 30000 {
+				label = "u-boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition at 40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition at 50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0x7b0000>;
+			};
+		};
+	};
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0x4>;
+};
+
+&esw {
+	mediatek,portmap = <0x2f>;
+};
+
+&wmac {
+	status = "okay";
+};
+
+&state_default {
+	default {
+		group = "i2c", "p0led_an", "p1led_an", "refclk", "wled_an";
+		function = "gpio";
+	};
+};
+
+&usbphy {
+	status = "disabled";
+};
+
+&ehci {
+	status = "disabled";
+};
+
+&ohci {
+	status = "disabled";
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 76fcab8787..074269a805 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -14,6 +14,30 @@ define Device/alfa-network_awusfree1
 endef
 TARGET_DEVICES += alfa-network_awusfree1
 
+define Device/asus_rt-n10p-v3
+  IMAGE_SIZE := 7872k
+  DEVICE_VENDOR := Asus
+  DEVICE_MODEL := RT-N10P
+  DEVICE_VARIANT := V3
+endef
+TARGET_DEVICES += asus_rt-n10p-v3
+
+define Device/asus_rt-n11p-b1
+  IMAGE_SIZE := 7872k
+  DEVICE_VENDOR := Asus
+  DEVICE_MODEL := RT-N11P
+  DEVICE_VARIANT := B1
+endef
+TARGET_DEVICES += asus_rt-n11p-b1
+
+define Device/asus_rt-n12-vp-b1
+  IMAGE_SIZE := 7872k
+  DEVICE_VENDOR := Asus
+  DEVICE_MODEL := RT-N12 VP
+  DEVICE_VARIANT := B1
+endef
+TARGET_DEVICES += asus_rt-n12-vp-b1
+
 define Device/buffalo_wcr-1166ds
   IMAGE_SIZE := 7936k
   BUFFALO_TAG_PLATFORM := MTK
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
index c66e13d3c5..685895452a 100755
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
@@ -20,6 +20,12 @@ case $board in
 alfa-network,awusfree1)
 	set_wifi_led "$boardname:blue:wlan"
 	;;
+asus,rt-n10p-v3|\
+asus,rt-n11p-b1|\
+asus,rt-n12-vp-b1)
+	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0xf"
+	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
+	;;
 cudy,wr1000)
 	ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x10"
 	ucidef_set_led_switch "lan1" "lan1" "$boardname:blue:lan1" "switch0" "0x08"
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index a6543fd38f..c69fcc6914 100755
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -26,6 +26,18 @@ ramips_setup_interfaces()
 		ucidef_add_switch_attr "switch0" "enable" "false"
 		ucidef_set_interface_lan "eth0"
 		;;
+	asus,rt-n10p-v3|\
+	asus,rt-n11p-b1|\
+	asus,rt-n12-vp-b1|\
+	hiwifi,hc5661a|\
+	mediatek,mt7628an-eval-board|\
+	mercury,mac1200r-v2|\
+	totolink,lr1200|\
+	wavlink,wl-wn570ha1|\
+	wavlink,wl-wn575a3)
+		ucidef_add_switch "switch0" \
+			"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6 at eth0"
+		;;
 	buffalo,wcr-1166ds)
 		ucidef_add_switch "switch0" \
 			"3:lan" "4:wan" "6 at eth0"
@@ -67,15 +79,6 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6 at eth0"
 		;;
-	hiwifi,hc5661a|\
-	mediatek,mt7628an-eval-board|\
-	mercury,mac1200r-v2|\
-	totolink,lr1200|\
-	wavlink,wl-wn570ha1|\
-	wavlink,wl-wn575a3)
-		ucidef_add_switch "switch0" \
-			"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6 at eth0"
-		;;
 	hiwifi,hc5761a)
 		ucidef_add_switch "switch0" \
 			"0:lan" "1:lan" "4:wan" "6 at eth0"
-- 
2.14.5


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel

More information about the openwrt-devel mailing list