[OpenWrt-Devel] [PATCH 19.07] ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1

Ernst Spielmann endspiel at disroot.org
Thu Apr 9 12:41:17 EDT 2020


Specifications:

- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)

Flash instructions:

1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.

Signed-off-by: Ernst Spielmann <endspiel at disroot.org>
---
 target/linux/ramips/base-files/etc/board.d/01_leds |   5 +
 .../linux/ramips/base-files/etc/board.d/02_network |   1 +
 target/linux/ramips/base-files/lib/ramips.sh       |   3 +
 target/linux/ramips/dts/RT-N11P_B1.dts             | 125 +++++++++++++++++++++
 target/linux/ramips/image/mt76x8.mk                |   7 ++
 5 files changed, 141 insertions(+)
 create mode 100644 target/linux/ramips/dts/RT-N11P_B1.dts

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5c005db0c1..c89af17d52 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -291,6 +291,11 @@ rp-n53)
 	ucidef_set_led_netdev "eth" "Network" "$boardname:white:back" "eth0"
 	set_wifi_led "$boardname:blue:wifi"
 	;;
+rt-n11p_b1)
+	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0xf"
+	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
+	ucidef_set_led_wlan "wlan" "wlan" "$boardname:green:wlan" "phy0tpt"
+	;;
 rt-n12p)
 	ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" eth0.1
 	ucidef_set_led_netdev "wan" "wan" "$boardname:green:wan" eth0.2
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index f743ce851a..4ea5cf0565 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -112,6 +112,7 @@ ramips_setup_interfaces()
 	pbr-m1|\
 	psg1208|\
 	psg1218a|\
+	rt-n11p_b1|\
 	rt-n12p|\
 	sap-g3200u3|\
 	sk-wb8|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 093303892c..d1caa9d5ea 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -439,6 +439,9 @@ ramips_board_detect() {
 	*"RT-N10+")
 		name="rt-n10-plus"
 		;;
+	*"RT-N11P B1")
+		name="rt-n11p_b1"
+		;;
 	*"RT-N12+")
 		name="rt-n12p"
 		;;
diff --git a/target/linux/ramips/dts/RT-N11P_B1.dts b/target/linux/ramips/dts/RT-N11P_B1.dts
new file mode 100644
index 0000000000..d2824f8995
--- /dev/null
+++ b/target/linux/ramips/dts/RT-N11P_B1.dts
@@ -0,0 +1,125 @@
+/dts-v1/;
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "asus,rt-n11p_b1", "mediatek,mt7628an-soc";
+	model = "Asus RT-N11P B1";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n11p_b1:green:power";
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n11p_b1:green:wlan";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+		};
+
+		wan {
+			label = "rt-n11p_b1:green:wan";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n11p_b1:green:lan";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		reset {
+			label = "reset";
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	m25p80 at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition at 30000 {
+				label = "u-boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition at 40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition at 50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0x7b0000>;
+			};
+		};
+	};
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0x4>;
+	mediatek,portmap = <0x3e>;
+};
+
+&wmac {
+	status = "okay";
+};
+
+&state_default {
+	default {
+		ralink,group = "refclk";
+		ralink,function = "gpio";
+	};
+};
+
+&usbphy {
+	status = "disabled";
+};
+
+&ehci {
+	status = "disabled";
+};
+
+&ohci {
+	status = "disabled";
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 7df5c04297..605e941c34 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -175,6 +175,13 @@ define Device/rakwireless_rak633
 endef
 TARGET_DEVICES += rakwireless_rak633
 
+define Device/rt-n11p_b1
+  DTS := RT-N11P_B1
+  IMAGE_SIZE := $(ralink_default_fw_size_8M)
+  DEVICE_TITLE := Asus RT-N10P V3/RT-N11P B1/RT-N12 VP B3
+endef
+TARGET_DEVICES += rt-n11p_b1
+
 define Device/skylab_skw92a
   DTS := SKW92A
   IMAGE_SIZE := 16064k
-- 
2.14.5


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list