[OpenWrt-Devel] [PATCH v3] mvebu: add support for Buffalo LinkStation LS421DE
Tomasz Maciej Nowak
tomek_n at o2.pl
Mon Apr 6 13:25:30 EDT 2020
W dniu 06.04.2020 o 01:06, Daniel Gonzalez Cabanelas pisze:
> Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370
>
> Hardware:
> SoC: Marvell Armada 88F6707-A1
> CPU: Cortex-A9 1200 MHz, 1 core
> Flash: SPI-NOR 1 MiB, NAND 512 MiB
> RAM: DDR3 512 MiB
> Ethernet: 1x 10/100/1000 Mbps
> USB: 1x 2.0, 1x 3.0
> SATA: 2x 3.0 Gbps
> LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
> RTC: Ricoh RS5C372A, I2C, no battery
>
> Flash instruction (UART+TFTP):
> 1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
> 2. Remove any hard drive from inside the bays.
> 3. Boot the Openwrt initramfs image using the U-Boot serial console:
> tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
> bootm 0x1200000
> 4. Flash the sysupgrade image using the Openwrt console:
> sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
> 5. Wait until it finish, the device will reboot with Openwrt installed
> on the NAND flash.
>
> Note:
> - Device shuting down doesn't work, even if the power slide switch is
> used. We must first, via MDIO, set the unused LED2 at the ethernet
> phy0 to off state. Reboot works ok.
>
> Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n at o2.pl>
> ---
> Changes in v2:
> - dts file tuned
> - Adjusted the i2c bus speed to the max supported by the RTC
> - Deleted unneded kernel patch
> - Image creation: only included neccesary packages, delete the ubinize
> parameter
>
> Changes in v3:
> - dts file tuned
> - Adjusted the i2c bus speed to the max supported by the SoC
> - Added vdd cpu power down pinmux
> - Image creation: adjusted the packages required by this device.
> Deleted redundant parameters.
> - Fixed installation instructions
>
> .../base-files/lib/preinit/06_set_iface_mac | 4 +
> .../base-files/lib/upgrade/platform.sh | 3 +
> .../boot/dts/armada-370-buffalo-ls421de.dts | 360 ++++++++++++++++++
> target/linux/mvebu/image/Makefile | 14 +
> target/linux/mvebu/image/cortexa9.mk | 16 +
> 5 files changed, 397 insertions(+)
> create mode 100644 target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
>
> diff --git a/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac b/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
> index fd41836c8d..62ce2653a0 100644
> --- a/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
> +++ b/target/linux/mvebu/cortexa9/base-files/lib/preinit/06_set_iface_mac
> @@ -9,6 +9,10 @@ preinit_set_mac_address() {
> . /lib/functions.sh
>
> case $(board_name) in
> + buffalo,ls421de)
> + mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
> + ip link set dev eth0 address $mac 2>/dev/null
> + ;;
> linksys,caiman|linksys,cobra|linksys,rango|linksys,shelby|linksys,venom)
> # rename interfaces back to the way they were with 4.4
> case "$(readlink /sys/class/net/eth0)" in
> diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
> index 8baed969a3..63042b1535 100755
> --- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
> @@ -22,6 +22,9 @@ platform_check_image() {
>
> platform_do_upgrade() {
> case "$(board_name)" in
> + buffalo,ls421de)
> + nand_do_upgrade "$1"
> + ;;
> cznic,turris-omnia|\
> solidrun,clearfog-base-a1|\
> solidrun,clearfog-pro-a1)
> diff --git a/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts b/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
> new file mode 100644
> index 0000000000..6b8a964ab3
> --- /dev/null
> +++ b/target/linux/mvebu/files-4.19/arch/arm/boot/dts/armada-370-buffalo-ls421de.dts
> @@ -0,0 +1,360 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for Buffalo LinkStation LS421DE
> + *
> + * Copyright (C) 2020 Daniel González Cabanelas <dgcbueu at gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "armada-370.dtsi"
> +#include "mvebu-linkstation-fan.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Buffalo LinkStation LS421DE";
> + compatible = "buffalo,ls421de", "marvell,armada370", "marvell,armada-370-xp";
> +
> + aliases {
> + led-boot = &led_boot;
> + led-failsafe = &led_failsafe;
> + led-running = &led_power;
> + led-upgrade = &led_upgrade;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200 earlyprintk noinitrd rootfstype=squashfs";
> + stdout-path = "serial0:115200n8";
> + append-rootblock = "nullparameter="; /* override the bootloader args */
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>; /* 512 MB */
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
> + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
> + MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
> + };
> +
> + gpio_fan {
> + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH
> + &gpio0 14 GPIO_ACTIVE_HIGH>;
> + alarm-gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_hdd_present &pmx_buttons>;
> + pinctrl-names = "default";
> +
> + hdd1-present {
> + label = "HDD1 Present";
> + linux,code = <KEY_PROG1>;
> + gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + hdd2-present {
> + label = "HDD2 Present";
> + linux,code = <KEY_PROG2>;
> + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
> +
> + };
> +
> + power {
> + label = "Power Switch";
> + linux,code = <KEY_POWER>;
> + linux,input-type = <EV_SW>;
> + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
> + };
> +
> + function {
> + label = "Function Button";
> + linux,code = <KEY_OPTION>;
> + gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + gpio_leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
> +
> + system_red {
> + label = "ls421de:red:system";
> + gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led_power: power_white {
> + label = "ls421de:white:power";
> + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> +
> + led_failsafe: power_red {
> + label = "ls421de:red:power";
> + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led_upgrade: power_orange {
> + label = "ls421de:orange:power";
> + gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led_boot: system_white {
> + label = "ls421de:white:system";
> + gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
> + };
> +
> + hdd1_red {
> + label = "ls421de:red:hdd1";
> + gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + linux,default-trigger = "disk-activity";
> + };
> +
> + hdd2_red {
> + label = "ls421de:red:hdd2";
> + gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + linux,default-trigger = "disk-activity";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_power_usb &pmx_power_hdd1 &pmx_power_hdd2>;
> +
> + pinctrl-names = "default";
> +
> + usb_v5_regulator: usb-v5-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "USB";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
> + };
> +
> + ata1_regulator: ata1-regulator {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "HDD1";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + startup-delay-us = <2000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
> + };
> +
> + ata2_regulator: ata2-regulator {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "HDD2";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + startup-delay-us = <4000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + /* FIXME: this driver needs to be aware of the LED2 eth phy use,
> + which must be set to off state before shutting down the machine */
> + restart_poweroff {
> + compatible = "restart-poweroff";
> + };
> +};
> +
> +ð1 {
> + pinctrl-0 = <&ge1_rgmii_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + phy = <&phy0>;
> + phy-mode = "rgmii-id";
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + rs5c372a: rs5c372a at 32 {
> + compatible = "ricoh,rs5c372a";
> + reg = <0x32>;
> + };
> +};
> +
> +&mdio {
> + pinctrl-0 = <&mdio_pins>;
> + pinctrl-names = "default";
> +
> + phy0: ethernet-phy at 0 { /* Marvell 88E1518 */
> + reg = <0>;
> + /* LED2 is used to inform uBoot if the power-switch was slided
> + to the "off" position, and then power off the machine.
> + Page 0x3, Register 0x10, bit 8:
> + 0x800: LED2 off, power off the machine
> + 0x900: LED2 on, boot the machine */
> + marvell,reg-init = <0x3 0x10 0x1 0x1991>, /* LED Function */
> + <0x3 0x11 0x1 0x4401>, /* LED polarity */
> + <0x3 0x12 0x1 0x4905>; /* LED Timer */
> + };
> +};
> +
> +&pciec {
> + status = "okay";
> + /* Connected to uPD720202 USB 3.0 Host */
> + pcie at 1,0 {
> + status = "okay";
> + };
> +};
> +
> +&pmsu {
> + pinctrl-0 = <&pmx_power_cpu>;
> + pinctrl-names = "default";
> +};
> +
> +&rtc {
> + status = "disabled";
> +};
> +
> +&sata {
> + nr-ports = <2>;
> + status = "okay";
> +};
> +
> +&sdio {
> + pinctrl-0 = <&sdio_pins2>;
> + pinctrl-names = "default";
> + status = "okay";
> + /* No CD or WP GPIOs */
> + broken-cd;
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&nand_controller {
> + status = "okay";
> +
> + nand at 0 {
> + reg = <0>;
> + label = "pxa3xx_nand-0";
> + nand-rb = <0>;
> + marvell,nand-keep-config;
> + nand-on-flash-bbt;
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "kernel";
> + reg = <0x00000000 0x02000000>; /* 32 MiB */
> + };
> +
> + partition at 2000000 {
> + label = "ubi";
> + reg = <0x02000000 0x1e000000>; /* 480 MiB */
> + };
> + };
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> + pinctrl-0 = <&spi0_pins2>;
> + pinctrl-names = "default";
> +
> + spi-flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "mxicy,mx25l8005", "jedec,spi-nor";
> + reg = <0>; /* Chip select 0 */
> + spi-max-frequency = <50000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + reg = <0x00000 0xf0000>; /* 960 KiB*/
> + label = "u-boot";
> + read-only;
> + };
> + partition at f0000 {
> + reg = <0xf0000 0x10000>; /* 64 KiB */
> + label = "u-boot-env";
> + };
> + };
> + };
> +};
> +
> +&pinctrl {
> + pmx_power_cpu: pmx-power-cpu {
> + marvell,pins = "mpp4";
> + marvell,function = "vdd";
> + };
> + pmx_power_usb: pmx-power-usb {
> + marvell,pins = "mpp5";
> + marvell,function = "gpo";
> + };
> + pmx_power_hdd1: pmx-power-hdd1 {
> + marvell,pins = "mpp8";
> + marvell,function = "gpio";
> + };
> + pmx_power_hdd2: pmx-power-hdd2 {
> + marvell,pins = "mpp9";
> + marvell,function = "gpo";
> + };
> + pmx_fan_lock: pmx-fan-lock {
> + marvell,pins = "mpp10";
> + marvell,function = "gpio";
> + };
> + pmx_hdd_present: pmx-hdd-present {
> + marvell,pins = "mpp11", "mpp12";
> + marvell,function = "gpio";
> + };
> + pmx_fan_high: pmx-fan-high {
> + marvell,pins = "mpp13";
> + marvell,function = "gpio";
> + };
> + pmx_fan_low: pmx-fan-low {
> + marvell,pins = "mpp14";
> + marvell,function = "gpio";
> + };
> + pmx_buttons: pmx-buttons {
> + marvell,pins = "mpp15", "mpp16";
> + marvell,function = "gpio";
> + };
> + pmx_leds1: pmx-leds {
> + marvell,pins = "mpp7", "mpp54", "mpp59", "mpp61";
> + marvell,function = "gpo";
> + };
> + pmx_leds2: pmx-leds {
> + marvell,pins = "mpp55", "mpp57", "mpp62";
> + marvell,function = "gpio";
> + };
> +};
> diff --git a/target/linux/mvebu/image/Makefile b/target/linux/mvebu/image/Makefile
> index ef9274866d..3a47878069 100644
> --- a/target/linux/mvebu/image/Makefile
> +++ b/target/linux/mvebu/image/Makefile
> @@ -40,6 +40,20 @@ define Build/boot-img-ext4
> make_ext4fs -J -L kernel -l $(CONFIG_TARGET_KERNEL_PARTSIZE)M $@.bootimg $@.boot
> endef
>
> +define Build/buffalo-kernel-jffs2
> + rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
> + mkdir -p $(KDIR)/kernel_jffs2
> + dd if=/dev/zero of=$@.fakerd bs=131008 count=1 conv=sync
> + $(STAGING_DIR_HOST)/bin/mkimage \
> + -T ramdisk -A $(LINUX_KARCH) -O linux -C gzip -n 'fake initrd' \
> + -d $@.fakerd $(KDIR)/kernel_jffs2/initrd.buffalo
> + cp $@ $(KDIR)/kernel_jffs2/uImage.buffalo
> + $(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
> + --little-endian -v --squash-uids -q -f -n -x lzma -x rtime -m none \
> + --eraseblock=128KiB --pad=$(KERNEL_SIZE) -d $(KDIR)/kernel_jffs2 -o $@
> + rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
> +endef
> +
> define Build/sdcard-img
> SIGNATURE="$(IMG_PART_SIGNATURE)" \
> ./gen_mvebu_sdcard_img.sh $@ \
> diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
> index 85bfa94dbd..4ab6f4a7e8 100644
> --- a/target/linux/mvebu/image/cortexa9.mk
> +++ b/target/linux/mvebu/image/cortexa9.mk
> @@ -6,6 +6,22 @@
> # See /LICENSE for more information.
> #
>
> +define Device/buffalo_ls421de
> + $(Device/NAND-128K)
> + DEVICE_VENDOR := Buffalo
> + DEVICE_MODEL := LinkStation LS421DE
> + SUBPAGESIZE :=
> + KERNEL_SIZE := 33554432
> + FILESYSTEMS := squashfs ubifs
> + KERNEL := kernel-bin | append-dtb | uImage none | buffalo-kernel-jffs2
> + KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
> + DEVICE_DTS := armada-370-buffalo-ls421de
> + DEVICE_PACKAGES := \
> + kmod-rtc-rs5c372a kmod-hwmon-gpiofan kmod-usb3 kmod-md-raid0 \
> + kmod-md-raid1 kmod-md-mod kmod-fs-xfs mkf2fs e2fsprogs partx-utils
> +endef
> +TARGET_DEVICES += buffalo_ls421de
> +
> define Device/cznic_turris-omnia
> DEVICE_VENDOR := CZ.NIC
> DEVICE_MODEL := Turris Omnia
>
--
TMN
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list