[OpenWrt-Devel] [PATCH v2] ath79: add support for COMFAST CF-E130N v2

admin at kryma.net admin at kryma.net
Wed Nov 13 13:22:38 EST 2019


From: Pavel Balan <admin at kryma.net>

This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.

Specifications:

 - QCA9531 SoC
 - 1x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 5 dBi built-in antenna
 - POWER/LAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI.

 The U-boot bootloader also contains a backup TFTP client to upload the
 firmware from. Upon boot, it checks its ethernet network for the IP
 192.168.1.10. Host a TFTP server and provide the image to be flashed as
 file firmware_auto.bin.

Changes since v1:

 -Formatting fixes.
 -Looked into rssi_medium_high more - found the correct GPIO pin.
 -Removed the pin muxer.
 -Changed 802.11an to 802.11bgn in the patch description.

Open questions:

 -LED menu in LUCI does not show the list of LEDs properly.
      A LUCI issue or a device config one?


Signed-off-by: Pavel Balan <admin at kryma.net>
---
 .../ath79/dts/qca9531_comfast_cf-e130n-v2.dts | 139 ++++++++++++++++++
 .../generic/base-files/etc/board.d/01_leds    |   8 +
 target/linux/ath79/image/generic.mk           |  10 ++
 3 files changed, 157 insertions(+)
 create mode 100644 target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts

diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
new file mode 100644
index 0000000000..b5527c0a49
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca953x.dtsi"
+
+/ {
+	compatible = "comfast,cf-e130n-v2", "qca,qca9531";
+	model = "COMFAST CF-E130N v2";
+
+	aliases {
+		serial0 = &uart;
+		led-boot = &led_rssihigh;
+		led-failsafe = &led_rssihigh;
+		led-upgrade = &led_rssihigh;
+		label-mac-device = &eth0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_rssimediumhigh_pin>;
+
+		led_wlan {
+			label = "cf-e130n-v2:green:wlan";
+			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		led_lan {
+			label = "cf-e130n-v2:green:lan";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led_unused {
+			label = "cf-e130n-v2:green:unused";
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led_rssilow {
+			label = "cf-e130n-v2:red:rssilow";
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led_rssimediumlow {
+			label = "cf-e130n-v2:red:rssimediumlow";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led_rssimediumhigh {
+			label = "cf-e130n-v2:green:rssimediumhigh";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led_rssihigh: led_rssihigh {
+			label = "cf-e130n-v2:green:rssihigh";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x000000 0x010000>;
+				read-only;
+			};
+
+			art: partition at 10000 {
+				label = "art";
+				reg = <0x010000 0x010000>;
+				read-only;
+			};
+
+			partition at 20000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x020000 0x7d0000>;
+			};
+
+			partition at 7f0000 {
+				label = "nvram";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+
+};
+
+&eth0 {
+	status = "okay";
+	phy-handle = <&swphy0>;
+
+	mtd-mac-address = <&art 0x0>;
+
+	gmac-config {
+		device = <&gmac>;
+		switch-phy-swap = <1>;
+	};
+};
+
+&wmac {
+	status = "okay";
+	mtd-cal-data = <&art 0x1000>;
+};
+
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index fbb0d0ea03..3046d34605 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -47,6 +47,14 @@ comfast,cf-e120a-v3)
 	ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssimediumhigh" "wlan0" "51" "100"
 	ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh" "wlan0" "76" "100"
 	;;
+comfast,cf-e130n-v2)
+	ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
+	ucidef_set_rssimon "wlan0" "200000" "1"
+	ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow" "wlan0" "1" "100"
+	ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "$boardname:red:rssimediumlow" "wlan0" "26" "100"
+	ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssimediumhigh" "wlan0" "51" "100"
+	ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh" "wlan0" "76" "100"
+	;;
 comfast,cf-e313ac)
 	ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x02"
 	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 70631c20d0..256481ece3 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -258,6 +258,16 @@ define Device/comfast_cf-e120a-v3
 endef
 TARGET_DEVICES += comfast_cf-e120a-v3
 
+define Device/comfast_cf-e130n-v2
+  ATH_SOC := qca9531
+  DEVICE_VENDOR := COMFAST
+  DEVICE_MODEL := CF-E130N
+  DEVICE_VARIANT := v2
+  DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools
+  IMAGE_SIZE := 8000k
+endef
+TARGET_DEVICES += comfast_cf-e130n-v2
+
 define Device/comfast_cf-e313ac
   ATH_SOC := qca9531
   DEVICE_VENDOR := COMFAST
-- 
2.17.1


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list