[OpenWrt-Devel] [PATCH v2] ath79: Add support for ZBT-WD323
Kristian Evensen
kristian.evensen at gmail.com
Fri May 31 09:43:14 EDT 2019
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen at gmail.com>
---
v1->v2:
* Added WLAN trigger to DTS (thanks Petr Štetiar).
* Fixed typo in compatible string (ar9334->ar9344, thanks Petr Štetiar).
* Removed a reundant alias (thanks Petr Štetiar).
* Changed compatible-value for keys (Petr Štetiar).
* Fixed LAN-port LEDs. I did not noticed that the LEDs did not work
peroply when I submitted v1.
---
.../ath79/base-files/etc/board.d/01_leds | 4 +
.../ath79/base-files/etc/board.d/02_network | 1 +
.../base-files/etc/board.d/03_gpio_switches | 6 +
.../ath79/dts/ar9344_zbtlink_zbt-wd323.dts | 163 ++++++++++++++++++
target/linux/ath79/image/generic.mk | 9 +
5 files changed, 183 insertions(+)
create mode 100644 target/linux/ath79/dts/ar9344_zbtlink_zbt-wd323.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 69e26a4773..a23f2e7c73 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -210,6 +210,10 @@ yuncore,a770)
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x10"
;;
+zbtlink,zbt-wd323)
+ ucidef_set_led_switch "lan1" "LAN1" "zbt-wd323:orange:lan1" "switch0" "0x10"
+ ucidef_set_led_switch "lan2" "LAN2" "zbt-wd323:orange:lan2" "switch0" "0x08"
+ ;;
esac
board_config_flush
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index c2e994530d..200782812b 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -258,6 +258,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "5:lan" "1:wan"
;;
+ zbtlink,zbt-wd323|\
xiaomi,mi-router-4q)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
diff --git a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches
index 6a51a79790..1c8a46df19 100755
--- a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches
@@ -29,6 +29,12 @@ ubnt,nanostation-ac)
ubnt,acb-isp)
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "11"
;;
+zbtlink,zbt-wd323)
+ ucidef_add_gpio_switch "io0" "IO#0" "0"
+ ucidef_add_gpio_switch "io1" "IO#1" "1"
+ ucidef_add_gpio_switch "io2" "IO#2" "2"
+ ucidef_add_gpio_switch "io14" "IO#14" "14"
+ ;;
esac
board_config_flush
diff --git a/target/linux/ath79/dts/ar9344_zbtlink_zbt-wd323.dts b/target/linux/ath79/dts/ar9344_zbtlink_zbt-wd323.dts
new file mode 100644
index 0000000000..6a7259a2fc
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_zbtlink_zbt-wd323.dts
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ model = "ZBT WD323";
+ compatible = "zbtlink,zbt-wd323", "qca,ar9344";
+
+ keys {
+ compatible = "gpio-keys";
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ i2c {
+ compatible = "i2c-gpio";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW
+ &gpio 15 GPIO_ACTIVE_LOW
+ >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&enable_gpio15 &enable_gpio19>;
+
+ pcf8563: pcf8563 at 51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&enable_gpio20_gpio22>;
+
+ wifi {
+ label = "zbt-wd323:green:wifi";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ lan1 {
+ label = "zbt-wd323:orange:lan1";
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ label = "zbt-wd323:orange:lan2";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+};
+
+&wdt {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&enable_gpio21>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&swphy4>;
+ mtd-mac-address = <&art 0x0>;
+};
+
+ð1 {
+ status = "okay";
+ mtd-mac-address = <&art 0x6>;
+};
+
+&spi {
+ num-chipselects = <1>;
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <22000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot at 0 {
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ uboot-env at 40000 {
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ firmware at 50000 {
+ compatible = "denx,uimage";
+ reg = <0x50000 0xfa0000>;
+ };
+
+ art: art at ff0000 {
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x1002>;
+};
+
+&pinmux {
+ enable_gpio15: pinmux_enable_gpio15 {
+ pinctrl-single,bits = <0xc 0x0 0xff000000>;
+ };
+
+ enable_gpio19: pinmux_enable_gpio19 {
+ pinctrl-single,bits = <0x10 0x0 0xff000000>;
+ };
+
+ enable_gpio20_gpio22: pinmux_enable_gpio20_gpio22 {
+ pinctrl-single,bits = <0x14 0x0 0xff00ff>;
+ };
+
+ enable_gpio21: pinmux_enable_gpio21 {
+ pinctrl-single,bits = <0x14 0x0 0xff00>;
+ };
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 1585379f83..3c9b171d35 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -701,3 +701,12 @@ define Device/yuncore_a770
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += yuncore_a770
+
+define Device/zbtlink_zbt-wd323
+ ATH_SOC := ar9344
+ DEVICE_TITLE := ZBT WD323
+ IMAGE_SIZE := 16000k
+ DEVICE_PACKAGES := kmod-usb2 kmod-i2c-core kmod-i2c-gpio kmod-rtc-pcf8563 \
+ kmod-usb-serial kmod-usb-serial-cp210x uqmi
+endef
+TARGET_DEVICES += zbtlink_zbt-wd323
--
2.19.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list