[OpenWrt-Devel] [PATCH] Support for Edimax EW-7476RPC / EW-7478AC
Birger Koblitz
mail at birger-koblitz.de
Mon May 27 11:55:24 EDT 2019
ramips: add Netgear EW-7476RPC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT76620a bgn
WiFi: MediaTek MT7612EN nac
GBE: RTL8211E
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Netgear EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT76620a bgn
WiFi: MediaTek MT7612EN nac
GBE: RTL8211E
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
b/target/linux/ramips/base-files/etc/board.d/01_leds
index b55ca0413e..78e93b557b 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -146,6 +146,10 @@ dir-860l-b1)
edimax,br-6478ac-v2)
set_wifi_led "$boardname:blue:wlan"
;;
+edimax,ew-7476rpc|\
+edimax,ew-7478ac)
+ ucidef_set_led_switch "lan" "lan" "$boardname:green:lan"
"switch0" "0x20"
+ ;;
ex2700|\
wn3000rpv3)
set_wifi_led "$boardname:green:router"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index 2e56678cf5..bbdfe9b128 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -50,6 +50,8 @@ ramips_setup_interfaces()
broadway|\
dcs-930|\
dcs-930l-b1|\
+ edimax,ew-7476rpc|\
+ edimax,ew-7478ac|\
ht-tm02|\
kimax,u35wf|\
linkits7688 | \
diff --git a/target/linux/ramips/dts/EW-7476RPC.dts
b/target/linux/ramips/dts/EW-7476RPC.dts
new file mode 100644
index 0000000000..7a1edf3e4d
--- /dev/null
+++ b/target/linux/ramips/dts/EW-7476RPC.dts
@@ -0,0 +1,238 @@
+/*
+ * Device Tree file for the Edimax EW-7476RPC
+ * based on Edimax BR-6478AC V2
+ *
+ * Copyright (C) 2016 Rohan Murch <rohan.murch at gmail.com>
+ * Copyright (C) 2016 Hans Ulli Kroll <ulli.kroll at googlemail.com>
+ * Copyright (C) 2017 James McKenzie <openwrt at madingley.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+
+ The following definitions were found in the orignal GPL firmware source
+ HW_LED_WIRELESS_ABAND_="71"
+ HW_LED_WIRELESS_GBAND_="70"
+ HW_LED_WIRELES_="69"
+ HW_LED_POWER_="67"
+ HW_LED_WPS_="68"
+ HW_LED_LAN_="66"
+ HW_BUTTON_APSWITCH_BUT_1_="62"
+ HW_BUTTON_APSWITCH_BUT_2_="63"
+ HW_BUTTON_RESET_="60"
+
+ The device does not have a reset button (but there are solder pads for
a button), WPS and reset are swapped.
+
+ */
+
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "edimax,ew-7476rpc", "ralink,mt7620a-soc";
+ model = "Edimax EW-7476RPC";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset_wps {
+ label = "reset_wps";
+ gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ switch_high {
+ label = "switch high";
+ gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ };
+ switch_off {
+ label = "switch off";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "ew-7476rpc:green:power";
+ gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+ };
+ lan {
+ label = "ew-7476rpc:green:lan";
+ gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ };
+ wlan2g {
+ label = "ew-7476rpc:blue:wlan2g";
+ gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1radio";
+ };
+ wlan5g {
+ label = "ew-7476rpc:blue:wlan5g";
+ gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0radio";
+ };
+ wps {
+ label = "ew-7476rpc:green:wps";
+ gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+ };
+ crossband {
+ label = "ew-7476rpc:green:crossband";
+ gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+
+&gpio2 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0 0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "cimage";
+ reg = <0x50000 0x20000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ compatible = "edimax,uimage";
+ label = "firmware";
+ reg = <0x00070000 0x00790000>;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ // might need pin 39: ;
+ ralink,group = "i2c", "uartf", "nd_sd",
"rgmii2", "spi refclk";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+
+ðernet {
+
+ status = "okay";
+ mtd-mac-address = <&factory 0x4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii1_pins &mdio_pins>;
+ mediatek,portmap = "l";
+ mediatek,mdio-mode = <1>;
+
+ port at 5 {
+ status = "okay";
+ mediatek,fixed-link = <1000 1 1 1>;
+ phy-mode = "rgmii";
+ };
+
+ mdio-bus {
+ status = "okay";
+
+ phy0: ethernet-phy at 0 {
+ status ="disabled";
+ reg = <0>;
+ phy-mode = "rgmii";
+ };
+
+ phy1: ethernet-phy at 1 {
+ status = "disabled";
+ reg = <1>;
+ phy-mode = "rgmii";
+ };
+
+ phy2: ethernet-phy at 2 {
+ status = "disabled";
+ reg = <2>;
+ phy-mode = "rgmii";
+ };
+
+ phy3: ethernet-phy at 3 {
+ status = "disabled";
+ reg = <3>;
+ phy-mode = "rgmii";
+ };
+
+ phy4: ethernet-phy at 4 {
+ status = "disabled";
+ reg = <4>;
+ phy-mode = "rgmii";
+ };
+ };
+};
+
+
+&gsw {
+ mediatek,port5 = "gmac";
+ mediatek,rtl8211e-reset = "yes";
+};
+
+
+&wmac {
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+};
diff --git a/target/linux/ramips/dts/EW-7478AC.dts
b/target/linux/ramips/dts/EW-7478AC.dts
new file mode 100644
index 0000000000..ab1b284280
--- /dev/null
+++ b/target/linux/ramips/dts/EW-7478AC.dts
@@ -0,0 +1,241 @@
+/*
+ * Device Tree file for the Edimax EW-7478AC
+ * based on Edimax BR-6478AC V2
+ *
+ * Copyright (C) 2016 Rohan Murch <rohan.murch at gmail.com>
+ * Copyright (C) 2016 Hans Ulli Kroll <ulli.kroll at googlemail.com>
+ * Copyright (C) 2017 James McKenzie <openwrt at madingley.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+
+ The following definitions were found in the orignal GPL firmware source
+ HW_LED_WIRELESS_ABAND_="71"
+ HW_LED_WIRELESS_GBAND_="70"
+ HW_LED_WIRELES_="69"
+ HW_LED_POWER_="67"
+ HW_LED_WPS_="68"
+ HW_LED_LAN_="66"
+ HW_BUTTON_APSWITCH_BUT_1_="62"
+ HW_BUTTON_APSWITCH_BUT_2_="63"
+ HW_BUTTON_RESET_="60"
+
+ The device does not have a reset button (but there are solder pads for
a button), WPS and reset are swapped.
+
+ */
+
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "edimax,ew-7478ac", "ralink,mt7620a-soc";
+ model = "Edimax EW-7478ac";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset_wps {
+ label = "reset_wps";
+ gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ switch_high {
+ label = "switch high";
+ gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ };
+
+ switch_off {
+ label = "switch off";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "ew-7478ac:green:power";
+ gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+ };
+ lan {
+ label = "ew-7478ac:green:lan";
+ gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ };
+ wlan2g {
+ label = "ew-7478ac:blue:wlan2g";
+ gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1radio";
+ };
+ wlan5g {
+ label = "ew-7478ac:blue:wlan5g";
+ gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0radio";
+ };
+ wps {
+ label = "ew-7478ac:green:wps";
+ gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+ };
+
+ crossband {
+ label = "ew-7478ac:green:crossband";
+ gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+
+&gpio2 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0 0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "cimage";
+ reg = <0x50000 0x20000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ compatible = "edimax,uimage";
+ label = "firmware";
+ reg = <0x00070000 0x00790000>;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ // might need pin 39: ;
+ ralink,group = "i2c", "uartf", "nd_sd",
"rgmii2", "spi refclk";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+
+ðernet {
+
+ status = "okay";
+ mtd-mac-address = <&factory 0x4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii1_pins &mdio_pins>;
+ mediatek,portmap = "l";
+ mediatek,mdio-mode = <1>;
+
+ port at 5 {
+ status = "okay";
+ mediatek,fixed-link = <1000 1 1 1>;
+ phy-mode = "rgmii";
+ };
+
+ mdio-bus {
+ status = "okay";
+
+ phy0: ethernet-phy at 0 {
+ status ="disabled";
+ reg = <0>;
+ phy-mode = "rgmii";
+ };
+
+ phy1: ethernet-phy at 1 {
+ status = "disabled";
+ reg = <1>;
+ phy-mode = "rgmii";
+ };
+
+ phy2: ethernet-phy at 2 {
+ status = "disabled";
+ reg = <2>;
+ phy-mode = "rgmii";
+ };
+
+ phy3: ethernet-phy at 3 {
+ status = "disabled";
+ reg = <3>;
+ phy-mode = "rgmii";
+ };
+
+ phy4: ethernet-phy at 4 {
+ status = "disabled";
+ reg = <4>;
+ phy-mode = "rgmii";
+ };
+ };
+};
+
+
+&gsw {
+ mediatek,port5 = "gmac";
+ mediatek,rtl8211e-reset = "yes";
+};
+
+
+&wmac {
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+};
diff --git
a/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
b/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
index 5fc5080aaf..305ce18037 100644
---
a/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
+++
b/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
@@ -84,6 +84,32 @@ static int mt7620_mdio_mode(struct device_node *eth_node)
return ret;
}
+void reset_realtek_phy(void){
+#define RALINK_GPIO_DIR 0xB0000600+0x4C
+#define RALINK_GPIO_DATA 0xB0000600+0x48
+#define RALINK_RESETPHY_GPIO (39-24)
+ u32 gpiodir;
+ u32 piodata;
+ u32 reset_pin= RALINK_RESETPHY_GPIO;
+
+ pr_info("gsw: Resetting RTL8211e using gpio 39\n");
+ gpiodir = le32_to_cpu(*(volatile u32 *)(RALINK_GPIO_DIR));
+ /*set gpio1 to output*/
+ gpiodir |= (1<<reset_pin);
+ *(volatile u32 *)(RALINK_GPIO_DIR) = cpu_to_le32(gpiodir);
+
+ piodata = le32_to_cpu(*(volatile u32 *)(RALINK_GPIO_DATA));
+ /*set to low(0)*/
+ piodata &= ~(1L << reset_pin);
+ *(volatile u32 *)(RALINK_GPIO_DATA) = cpu_to_le32(piodata);
+ /*delay 30ms*/
+ mdelay(30);
+ /*set to high(1)*/
+ piodata |= (1L << reset_pin);
+ *(volatile u32 *)(RALINK_GPIO_DATA) = cpu_to_le32(piodata);
+}
+
+
static void mt7620_hw_init(struct mt7620_gsw *gsw, int mdio_mode)
{
u32 i;
@@ -220,6 +246,7 @@ int mtk_gsw_init(struct fe_priv *priv)
struct device_node *np = priv->switch_np;
struct platform_device *pdev = of_find_device_by_node(np);
struct mt7620_gsw *gsw;
+ const char *rtl8211e_reset = NULL;
if (!pdev)
return -ENODEV;
@@ -231,6 +258,9 @@ int mtk_gsw_init(struct fe_priv *priv)
priv->soc->swpriv = gsw;
mt7620_hw_init(gsw, mt7620_mdio_mode(priv->dev->of_node));
+ of_property_read_string(np, "mediatek,rtl8211e-reset",
&rtl8211e_reset);
+ if (rtl8211e_reset && !strcmp(rtl8211e_reset, "yes"))
+ reset_realtek_phy();
if (gsw->irq) {
request_irq(gsw->irq, gsw_interrupt_mt7620, 0,
diff --git a/target/linux/ramips/image/mt7620.mk
b/target/linux/ramips/image/mt7620.mk
index cf38aa2cb1..a7b14593c2 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -617,6 +617,32 @@ define Device/edimax_br-6478ac-v2
endef
TARGET_DEVICES += edimax_br-6478ac-v2
+define Device/edimax_ew-7476rpc
+ DTS := EW-7476RPC
+ DEVICE_TITLE := Edimax EW-7476RPC
+ BLOCKSIZE := 4k
+ IMAGE_SIZE := 7616k
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
+ edimax-header -s CSYS -m RN79 -f 0x70000 -S 0x01100000 |
pad-rootfs | \
+ append-metadata | check-size $$$$(IMAGE_SIZE)
+ DEVICE_PACKAGES := kmod-mt76x2 kmod-phy-realtek
+endef
+TARGET_DEVICES += edimax_ew-7476rpc
+
+
+define Device/edimax_ew-7478ac
+ DTS := EW-7478AC
+ DEVICE_TITLE := Edimax EW-7478AC
+ BLOCKSIZE := 4k
+ IMAGE_SIZE := 7616k
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
+ edimax-header -s CSYS -m RN70 -f 0x70000 -S 0x01100000 |
pad-rootfs | \
+ append-metadata | check-size $$$$(IMAGE_SIZE)
+ DEVICE_PACKAGES := kmod-mt76x2 kmod-phy-realtek
+endef
+TARGET_DEVICES += edimax_ew-7478ac
+
+
define Device/tplink_c2-v1
$(Device/Archer)
DTS := ArcherC2-v1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list