[OpenWrt-Devel] [PATCH] ath10k: reset chip after supported check

Ben Greear greearb at candelatech.com
Mon Mar 25 16:29:32 EDT 2019


On 03/25/2019 02:34 PM, Michał Kazior wrote:
> On Mon, 25 Mar 2019 at 21:23, Ben Greear <greearb at candelatech.com> wrote:
>>
>> On 3/25/19 1:08 PM, Michał Kazior wrote:
>>> On Mon, 25 Mar 2019 at 16:55, Ben Greear <greearb at candelatech.com> wrote:
>>>> On 3/25/19 5:14 AM, Michał Kazior wrote:
>>>>> On Sat, 23 Mar 2019 at 08:20, Arend Van Spriel
>>>>> <arend.vanspriel at broadcom.com> wrote:
>>>>>>
>>>>>> * resending with corrected email address from Kalle
>>>>>> --------------------------------------------------------------------
>>>>>> + Michał
>>>>>
>>>>> Thanks!
>>>>>
>>>>>
>>>>>> On 3/22/2019 8:25 PM, Christian Lamparter wrote:
>>>>>>     > On Friday, March 22, 2019 7:58:40 PM CET Tomislav Požega wrote:
>>>>>>     >> When chip reset is done before the chip is checked if supported
>>>>>>     >> there will be crash. Previous behaviour caused bootloops on
>>>>>>     >> Archer C7 v1 units, this patch allows clean device boot without
>>>>>>     >> excluding ath10k driver.
>>>>>
>>>>> Can you elaborate more a bit? What kind of crashes are you seeing?
>>>>> What does the bootloop look like? Do you have uart connected to
>>>>> diagnose?
>>>>>
>>>>> Didn't C7 v1 have the old QCA9880 hw v1 which isn't really supported
>>>>> by ath10k? I recall the v1 chip was really buggy and required
>>>>> hammering registers sometimes to get things working.
>>>>
>>>> The crash is related to the v1 chip.  Is there a good way to detect
>>>> that this is the chip in question and only apply this work-around
>>>> for the problem chip?
>>>
>>> I don't know of any good way to do that.
>>>
>>> You could consider device-tree but that would be no different from
>>> having a module blacklist in the C7v1 build recipe, or to not build
>>> the module at all. That is unless you actually want to make v1 chip
>>> work with ath10k at which point there's more fun to be had before it
>>> can actually work.
>>
>> I remember v1, and I have no interest in trying to make it work :)
>>
>> If we could blacklist certain pci slots in the ath10k driver, I guess
>> that would work?
>>
>> I think the goal is to not use the v1 chip, but allow users to add a
>> v2 NIC to the platform, so driver still needs to load.
>
> That makes sense, but I don't see how blacklisting pci slots would
> help someone putting v2 nic into C7v1 mobo? Won't the slot be the same
> regardless what nic is put?

I'm not sure about that...maybe let OpenWRT boot by default
assuming the slot is blacklisted, and then disable the blacklist
if known to be a v2 NIC.

If your patch below works, that looks a lot better though.

Hopefully someone with that v1 board can test it.

Thanks,
Ben

>
> The best thing I can come up with is something like this:
>
> --- a/drivers/net/wireless/ath/ath10k/pci.c
> +++ b/drivers/net/wireless/ath/ath10k/pci.c
> @@ -3629,6 +3629,19 @@ static int ath10k_pci_probe(struct pci_dev *pdev,
>                  goto err_deinit_irq;
>          }
>
> +       if (hw_rev == ATH10K_HW_QCA988X) {
> +               /* v1 can crash the system on chip_reset()
> +                * so all we can do is keep our fingers
> +                * crossed v2 never reports 0 without a
> +                * chip_reset()
> +                */
> +               if (ath10k_pci_soc_read32(ar, SOC_CHIP_ID_ADDRESS) == 0) {
> +                       ath10k_err(ar, "qca9880 v1 is chip not supported");
> +                       ret = -ENOTSUP;
> +                       goto err_free_irq;
> +               }
> +       }
> +
>          ret = ath10k_pci_chip_reset(ar);
>          if (ret) {
>                  ath10k_err(ar, "failed to reset chip: %d\n", ret);
>
> I didn't test it. Someone needs to compile and test and make sure v2
> doesn't regress when fw hangs and cold & warm host cpu resets are
> mixed in.
>
>
> Michał
>


-- 
Ben Greear <greearb at candelatech.com>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list