[OpenWrt-Devel] [PATCH v4 6/6] ramips: Merge ath9k-eeprom extraction to common eeprom.sh

Adrian Schmutzler freifunk at adrianschmutzler.de
Fri Mar 1 09:40:22 EST 2019


This uses the common eeprom extraction functions in eeprom.sh.
As a by-product, this will bring the speed enhancement through
blockwise reading to the ramips target.

This patch is based on the proposed unification by Petr Štetiar.

Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>

---

New in v3:
This is cut out from Petr's initial unification proposal, as I
do not own a ramips device to test.

Changed in v4:
- Rebased
---
 .../etc/hotplug.d/firmware/10-rt2x00-eeprom        | 32 +++++-----------------
 1 file changed, 7 insertions(+), 25 deletions(-)

diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 13a4687251..60b0e68bff 100644
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -1,24 +1,5 @@
 #!/bin/sh
 
-rt2x00_eeprom_die() {
-	echo "rt2x00 eeprom: " "$*"
-	exit 1
-}
-
-rt2x00_eeprom_extract() {
-	local part=$1
-	local offset=$2
-	local count=$3
-	local mtd
-
-	mtd=$(find_mtd_part $part)
-	[ -n "$mtd" ] || \
-		rt2x00_eeprom_die "no mtd device found for partition $part"
-
-	dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
-		rt2x00_eeprom_die "failed to extract from $mtd"
-}
-
 jboot_eeprom_extract() {
 	local part=$1
 	local offset=$2
@@ -26,21 +7,21 @@ jboot_eeprom_extract() {
 
 	mtd=$(find_mtd_part $part)
 	[ -n "$mtd" ] || \
-		rt2x00_eeprom_die "no mtd device found for partition $part"
+		eeprom_die "no mtd device found for partition $part"
 
 	jboot_config_read -i $mtd -o $offset -e /lib/firmware/$FIRMWARE  2>/dev/null || \
-		rt2x00_eeprom_die "failed to extract from $mtd"
+		eeprom_die "failed to extract from $mtd"
 }
 
 rt2x00_eeprom_set_macaddr() {
 	local macaddr=$1
 
 	[ -n "$macaddr" ] || \
-		rt2x00_eeprom_die "invalid wlan mac address"
+		eeprom_die "invalid wlan mac address"
 
 	macaddr_2bin $macaddr | dd of=/lib/firmware/$FIRMWARE \
 				conv=notrunc bs=1 seek=4 count=6 2>/dev/null || \
-		rt2x00_eeprom_die "failed to write mac address to eeprom file"
+		eeprom_die "failed to write mac address to eeprom file"
 }
 
 FW="/lib/firmware/$FIRMWARE"
@@ -48,6 +29,7 @@ FW="/lib/firmware/$FIRMWARE"
 
 . /lib/functions.sh
 . /lib/functions/system.sh
+. /lib/functions/eeprom.sh
 
 board=$(board_name)
 
@@ -67,11 +49,11 @@ case "$FIRMWARE" in
 		;;
 	tiny-ac)
 		wifi_mac=$(mtd_get_mac_ascii u-boot-env INIC_MAC_ADDR)
-		rt2x00_eeprom_extract "factory" 0 512
+		mtd_eeprom_extract "factory" 0 512
 		rt2x00_eeprom_set_macaddr $wifi_mac
 		;;
 	*)
-		rt2x00_eeprom_die "Please define mtd-eeprom in $board DTS file!"
+		eeprom_die "Please define mtd-eeprom in $board DTS file!"
 		;;
 	esac
 	;;
-- 
2.11.0


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list