[OpenWrt-Devel] [PATCH] mpc85xx: add support for Sophos RED 15w Rev.1

David Bauer mail at david-bauer.net
Sun Jan 6 11:29:54 EST 2019


Hardware
========
CPU:  Freescale P1010 PowerPC
RAM:  128M DDR3
NAND: 128MiB
ETH:  RTL8211F SGMII PHY
      RTL8367B 5-port RGMII switch
      (not connected to SoC - unmanaged)
WiFi: SparkLan WPEA-121N
       - Atheros AR9382 2T2R abgn
USB:  1x USB 2.0
LED:  System, Router, Internet, Tunnel controllable
      LAN1-4, WAN, Power non-controllable
BTN:  None

Installation
============
1. Power on the device while attached to the Console port.

2. Halt the U-Boot by pressing Enter when prompted.

3. Set the correct bootcmd for booting OpenWRT:
 > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
 > setenv bootcmd "run bootargs_owrt;
   nand read 0x1000000 0x300000 0x800000;
   bootm 0x1000000;"
 > saveenv

5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
   TFTP server root-directory served on 192.168.1.2/24. Connect your
   computer to one of the LAN-ports.

4. Boot OpenWRT initramfs image with
 > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
   bootm 0x1000000;

6. (Optional)
   Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
   you ever want to go back to the vendor firmware.

7. Create Ubi Volume on mtd4 by executing
 > ubiformat /dev/mtd4 -y

8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
   with
 > sysupgrade -n <openwrt-image-file>

Back to Stock
=============
If you want to go back to the stock firmware, here is the bootcmd of the
vendor firmware:
 > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
   nand read 0xc00000 0x00300000  0x100000;
   nand read 0x1000000 0x00400000 0x00800000;
   bootm 0x1000000 - 0xc00000

Set it via 'setenv' from the U-Boot shell and don't forget to save it
using 'saveenv'!

After this, boot the OpenWRT initramfs image just like you would for
installation. Write back the three vendor partitions using mtd. Reboot
the device afterwards.

Signed-off-by: David Bauer <mail at david-bauer.net>
---
 target/linux/mpc85xx/Makefile                 |   2 +-
 target/linux/mpc85xx/base-files/etc/diag.sh   |   3 +
 .../etc/hotplug.d/ieee80211/10-fix-wifi-mac   |  20 ++
 .../base-files/lib/upgrade/platform.sh        |  13 +-
 target/linux/mpc85xx/config-4.14              |  16 ++
 target/linux/mpc85xx/config-4.19              |  16 ++
 .../arch/powerpc/boot/dts/red-15w-rev1.dts    | 203 ++++++++++++++++++
 .../arch/powerpc/platforms/85xx/red15w_rev1.c |  85 ++++++++
 target/linux/mpc85xx/image/Makefile           |  12 ++
 target/linux/mpc85xx/p1020/target.mk          |   1 -
 .../104-powerpc-85xx-red-15w-rev1.patch       |  33 +++
 .../103-powerpc-85xx-red-15w-rev1.patch       |  33 +++
 12 files changed, 434 insertions(+), 3 deletions(-)
 create mode 100644 target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
 create mode 100644 target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts
 create mode 100644 target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c
 create mode 100644 target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch
 create mode 100644 target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch

diff --git a/target/linux/mpc85xx/Makefile b/target/linux/mpc85xx/Makefile
index 552f16e82f..c6555cb688 100644
--- a/target/linux/mpc85xx/Makefile
+++ b/target/linux/mpc85xx/Makefile
@@ -10,7 +10,7 @@ ARCH:=powerpc
 BOARD:=mpc85xx
 BOARDNAME:=Freescale MPC85xx
 CPU_TYPE:=8540
-FEATURES:=squashfs
+FEATURES:=squashfs nand ramdisk
 MAINTAINER:=Imre Kaloz <kaloz at openwrt.org>
 SUBTARGETS:=generic p1020
 
diff --git a/target/linux/mpc85xx/base-files/etc/diag.sh b/target/linux/mpc85xx/base-files/etc/diag.sh
index 3d56d14b08..e344d4b756 100644
--- a/target/linux/mpc85xx/base-files/etc/diag.sh
+++ b/target/linux/mpc85xx/base-files/etc/diag.sh
@@ -9,6 +9,9 @@ get_status_led() {
 	aerohive,hiveap-330)
 		status_led="hiveap-330:green:tricolor0"
 		;;
+	sophos,red-15w-rev1)
+		status_led="red-15w-rev1:green:system"
+		;;
 	tplink,tl-wdr4900-v1)
 		status_led="tp-link:blue:system"
 		;;
diff --git a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
new file mode 100644
index 0000000000..3092cebfc9
--- /dev/null
+++ b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
@@ -0,0 +1,20 @@
+#!/bin/ash
+
+[ "$ACTION" == "add" ] || exit 0
+
+PHYNBR=${DEVPATH##*/phy}
+
+[ -n $PHYNBR ] || exit 0
+
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(board_name)
+
+case "$board" in
+sophos,red-15w-rev1)
+	echo $(mtd_get_mac_ascii u-boot-env ethaddr) > /sys${DEVPATH}/macaddress
+	;;
+*)
+	;;
+esac
diff --git a/target/linux/mpc85xx/base-files/lib/upgrade/platform.sh b/target/linux/mpc85xx/base-files/lib/upgrade/platform.sh
index 1108b3fd6e..9f49d0ddce 100755
--- a/target/linux/mpc85xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mpc85xx/base-files/lib/upgrade/platform.sh
@@ -9,4 +9,15 @@ platform_check_image() {
 	return 0
 }
 
-# use default for platform_do_upgrade()
+platform_do_upgrade() {
+	local board=$(board_name)
+
+	case "$board" in
+	sophos,red-15w-rev1)
+		nand_do_upgrade "$ARGV"
+		;;
+	*)
+		default_do_upgrade "$ARGV"
+		;;
+	esac
+}
diff --git a/target/linux/mpc85xx/config-4.14 b/target/linux/mpc85xx/config-4.14
index 5bed475664..e81ff1cda0 100644
--- a/target/linux/mpc85xx/config-4.14
+++ b/target/linux/mpc85xx/config-4.14
@@ -88,6 +88,7 @@ CONFIG_ETHERNET_PACKET_MANGLE=y
 CONFIG_FIXED_PHY=y
 # CONFIG_FORCE_SMP is not set
 CONFIG_FSL_BOOKE=y
+# CONFIG_FSL_CORENET_CF is not set
 # CONFIG_FSL_DPAA is not set
 CONFIG_FSL_EMB_PERFMON=y
 # CONFIG_FSL_FMAN is not set
@@ -213,7 +214,16 @@ CONFIG_MPIC_TIMER=y
 CONFIG_MPILIB=y
 # CONFIG_MTD_CFI is not set
 CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_FSL_IFC=y
 CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
 # CONFIG_MVME2500 is not set
 # CONFIG_NEED_DMA_MAP_STATE is not set
 # CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
@@ -306,6 +316,8 @@ CONFIG_QUICC_ENGINE=y
 CONFIG_RAS=y
 # CONFIG_RCU_NEED_SEGCBLIST is not set
 # CONFIG_RCU_STALL_COMMON is not set
+CONFIG_REALTEK_PHY=y
+CONFIG_RED_15W_REV1=y
 CONFIG_REGMAP=y
 CONFIG_REGMAP_I2C=y
 CONFIG_REGMAP_SPI=y
@@ -348,6 +360,10 @@ CONFIG_TINY_SRCU=y
 # CONFIG_TQM8555 is not set
 # CONFIG_TQM8560 is not set
 # CONFIG_TWR_P102x is not set
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
 CONFIG_UCC=y
 CONFIG_UCC_FAST=y
 CONFIG_UCC_GETH=y
diff --git a/target/linux/mpc85xx/config-4.19 b/target/linux/mpc85xx/config-4.19
index 0aaefe84ea..63cd5c6c01 100644
--- a/target/linux/mpc85xx/config-4.19
+++ b/target/linux/mpc85xx/config-4.19
@@ -86,6 +86,7 @@ CONFIG_ETHERNET_PACKET_MANGLE=y
 # CONFIG_FHCI_DEBUG is not set
 CONFIG_FIXED_PHY=y
 CONFIG_FSL_BOOKE=y
+# CONFIG_FSL_CORENET_CF is not set
 # CONFIG_FSL_DPAA is not set
 CONFIG_FSL_EMB_PERFMON=y
 # CONFIG_FSL_FMAN is not set
@@ -199,7 +200,16 @@ CONFIG_MPIC_TIMER=y
 CONFIG_MPILIB=y
 # CONFIG_MTD_CFI is not set
 CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_FSL_IFC=y
 CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
 # CONFIG_MVME2500 is not set
 CONFIG_NEED_PER_CPU_KM=y
 CONFIG_NEED_SG_DMA_LENGTH=y
@@ -269,6 +279,8 @@ CONFIG_QE_GPIO=y
 CONFIG_QE_USB=y
 CONFIG_QUICC_ENGINE=y
 CONFIG_RAS=y
+CONFIG_REALTEK_PHY=y
+CONFIG_RED_15W_REV1=y
 CONFIG_REGMAP=y
 CONFIG_REGMAP_I2C=y
 CONFIG_REGMAP_SPI=y
@@ -309,6 +321,10 @@ CONFIG_TINY_SRCU=y
 # CONFIG_TQM8555 is not set
 # CONFIG_TQM8560 is not set
 # CONFIG_TWR_P102x is not set
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
 CONFIG_UCC=y
 CONFIG_UCC_FAST=y
 CONFIG_UCC_GETH=y
diff --git a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts
new file mode 100644
index 0000000000..06b206a73d
--- /dev/null
+++ b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/red-15w-rev1.dts
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0-or-later or MIT
+
+/include/ "fsl/p1010si-pre.dtsi"
+
+/ {
+	model = "Sophos RED 15w Rev.1";
+	compatible = "sophos,red-15w-rev1";
+
+	memory {
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		system_green {
+			gpios = <&gpio0 7 0>;
+			label = "red-15w-rev1:green:system";
+		};
+
+		system_red {
+			gpios = <&gpio0 3 0>;
+			label = "red-15w-rev1:red:system";
+		};
+
+		router {
+			gpios = <&gpio0 5 1>;
+			label = "red-15w-rev1:green:router";
+		};
+
+		internet {
+			gpios = <&gpio0 4 1>;
+			label = "red-15w-rev1:green:internet";
+		};
+
+		tunnel {
+			gpios = <&gpio0 8 1>;
+			label = "red-15w-rev1:green:tunnel";
+		};
+	};
+
+	soc: soc at ffe00000 {
+		ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+		i2c at 3000 {
+			eeprom at 50 {
+				compatible = "st,24c256";
+				reg = <0x50>;
+			};
+		};
+
+		i2c at 3100 {
+			eeprom at 52 {
+				compatible = "atmel,24c01";
+				reg = < 0x52 >;
+			};
+		};
+
+		gpio0: gpio-controller at fc00 {
+		};
+
+		usb at 22000 {
+			phy_type = "utmi";
+			dr_mode = "host";
+		};
+
+		mdio at 24000 {
+			phy0: ethernet-phy at 0 {
+				reg = <0x0>;
+			};
+		};
+
+		mdio at 25000 {
+			tbi_phy: tbi-phy at 11 {
+				reg = <0x11>;
+			};
+		};
+
+		mdio at 26000 {
+			status = "disabled";
+		};
+
+		enet0: ethernet at b0000 {
+			phy-connection-type = "rgmii-id";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		enet1: ethernet at b1000 {
+			phy-handle = <&phy0>;
+			phy-connection-type = "sgmii";
+
+			tbi-handle = <&tbi_phy>;
+		};
+
+		enet2: ethernet at b2000 {
+			status = "disabled";
+		};
+
+		sdhc at 2e000 {
+			status = "disabled";
+		};
+	};
+
+	ifc: ifc at ffe1e000 {
+		reg = <0x0 0xffe1e000 0 0x2000>;
+
+		/* NOR, NAND Flashes and CPLD on board */
+		ranges = <0x0 0x0 0x0 0xee000000 0x02000000
+			0x1 0x0 0x0 0xff800000 0x00010000
+			0x3 0x0 0x0 0xffb00000 0x00000020>;
+
+		nand at 1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x1 0x0 0x10000>;
+
+			/*
+			 * Original partition layout:
+			 * 0x000000000000-0x000000100000 : "NAND U-Boot Image"
+			 * 0x000000100000-0x000000200000 : "NAND U-Boot Environment"
+			 * 0x000000200000-0x000000300000 : "Provisioning"
+			 *  - OS-Image 1
+			 * 0x000000300000-0x000000400000 : "fdt1"
+			 * 0x000000400000-0x000000c00000 : "uimage1"
+			 * 0x000000c00000-0x000001c00000 : "rootfs1"
+			 *  - OS-Image 2
+			 * 0x000001c00000-0x000001d00000 : "fdt2"
+			 * 0x000001d00000-0x000002500000 : "uimage2"
+			 * 0x000002500000-0x000003500000 : "rootfs2"
+			 *  - Empty
+			 * 0x000003500000-0x000008000000 : "data"
+			 */
+
+			partition at 0 {
+				reg = <0x0 0x100000>;
+				label = "u-boot";
+				read-only;
+			};
+
+			partition at 100000 {
+				reg = <0x100000 0x100000>;
+				label = "u-boot-env";
+			};
+
+			partition at 200000 {
+				reg = <0x200000 0x100000>;
+				label = "provisioning";
+				read-only;
+			};
+
+			partition at 300000 {
+				reg = <0x300000 0x800000>;
+				label = "kernel";
+			};
+
+			partition at b00000 {
+				reg = <0xb00000 0x7500000>;
+				label = "ubi";
+			};
+
+			oem-partition at 300000 {
+				reg = <0x300000 0x1900000>;
+				label = "sophos-os1";
+			};
+
+			oem-partition at 1c00000 {
+				reg = <0x1c00000 0x1900000>;
+				label = "sophos-os2";
+			};
+
+			oem-partition at 3500000 {
+				reg = <0x3500000 0x4b00000>;
+				label = "sophos-data";
+			};
+		};
+	};
+
+	pci0: pcie at ffe09000 {
+		status = "disabled";
+	};
+
+	pci1: pcie at ffe0a000 {
+		reg = <0 0xffe0a000 0 0x1000>;
+		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+		pcie at 0 {
+			ranges = <0x2000000 0x0 0x80000000
+				  0x2000000 0x0 0x80000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+};
+
+/include/ "fsl/p1010si-post.dtsi"
diff --git a/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c
new file mode 100644
index 0000000000..85af7dcbcb
--- /dev/null
+++ b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/red15w_rev1.c
@@ -0,0 +1,85 @@
+/*
+ * Sophos RED 15w Rev.1 Board Setup
+ *
+ * Copyright (C) 2019 David Bauer <mail at david-bauer.net>
+ *
+ * Based on:
+ *   p1010rdb.c:
+ *      P1010 RDB Board Setup
+ *      Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc85xx.h"
+
+void __init red_15w_rev1_pic_init(void)
+{
+	struct mpic *mpic;
+
+	mpic = mpic_alloc(NULL, 0,
+	  MPIC_BIG_ENDIAN | MPIC_SINGLE_DEST_CPU,
+	  0, 256, " OpenPIC  ");
+
+	BUG_ON(mpic == NULL);
+	mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init red_15w_rev1_setup_arch(void)
+{
+	if (ppc_md.progress)
+		ppc_md.progress("red_15w_rev1_setup_arch()", 0);
+
+	fsl_pci_assign_primary();
+
+	printk(KERN_INFO "RED 15w Rev.1 from Sophos\n");
+}
+
+machine_arch_initcall(red_15w_rev1, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init red_15w_rev1_probe(void)
+{
+	if (of_machine_is_compatible("sophos,red-15w-rev1"))
+		return 1;
+	return 0;
+}
+
+define_machine(red_15w_rev1) {
+	.name			= "P1010 RDB",
+	.probe			= red_15w_rev1_probe,
+	.setup_arch		= red_15w_rev1_setup_arch,
+	.init_IRQ		= red_15w_rev1_pic_init,
+#ifdef CONFIG_PCI
+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
+#endif
+	.get_irq		= mpic_get_irq,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+};
diff --git a/target/linux/mpc85xx/image/Makefile b/target/linux/mpc85xx/image/Makefile
index 00eed88874..0c249a5131 100644
--- a/target/linux/mpc85xx/image/Makefile
+++ b/target/linux/mpc85xx/image/Makefile
@@ -57,6 +57,18 @@ define Device/tl-wdr4900-v1
 endef
 TARGET_DEVICES += tl-wdr4900-v1
 
+define Device/red-15w-rev1
+  DEVICE_TITLE := Sophos RED 15w Rev.1
+  DEVICE_PACKAGES := kmod-usb2
+  # Original firmware uses a dedicated DTB-partition.
+  # The bootloader however supports FIT-images.
+  KERNEL = kernel-bin | gzip | fit gzip $(KDIR)/image-$$(DEVICE_DTS).dtb
+  SUPPORTED_DEVICES := sophos,red-15w-rev1
+  IMAGES := sysupgrade.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += red-15w-rev1
+
 endif
 
 ifeq ($(SUBTARGET),p1020)
diff --git a/target/linux/mpc85xx/p1020/target.mk b/target/linux/mpc85xx/p1020/target.mk
index 5d84d83205..000fc64644 100644
--- a/target/linux/mpc85xx/p1020/target.mk
+++ b/target/linux/mpc85xx/p1020/target.mk
@@ -1,5 +1,4 @@
 BOARDNAME:=P1020
-FEATURES += ramdisk
 
 define Target/Description
 	Build firmware images for Freescale P1020 based boards.
diff --git a/target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch b/target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch
new file mode 100644
index 0000000000..452a6cd490
--- /dev/null
+++ b/target/linux/mpc85xx/patches-4.14/104-powerpc-85xx-red-15w-rev1.patch
@@ -0,0 +1,33 @@
+Index: linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
+===================================================================
+--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Kconfig
++++ linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
+@@ -173,6 +173,16 @@ config XES_MPC85xx
+ 	  Manufacturer: Extreme Engineering Solutions, Inc.
+ 	  URL: <http://www.xes-inc.com/>
+ 
++config RED_15W_REV1
++	bool "Sophos RED 15w Rev.1"
++	select DEFAULT_UIMAGE
++	select ARCH_REQUIRE_GPIOLIB
++	select GPIO_MPC8XXX
++	help
++	  This option enables support for the SOPHOS RED 15w Rev.1 board.
++
++	  This board is a wireless VPN router with a Freescale P1010 SoC.
++
+ config STX_GP3
+ 	bool "Silicon Turnkey Express GP3"
+ 	help
+Index: linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
+===================================================================
+--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Makefile
++++ linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
+@@ -25,6 +25,7 @@ obj-$(CONFIG_P1023_RDB)   += p1023_rdb.o
+ obj-$(CONFIG_TWR_P102x)   += twr_p102x.o
+ obj-$(CONFIG_CORENET_GENERIC)   += corenet_generic.o
+ obj-$(CONFIG_FB_FSL_DIU)	+= t1042rdb_diu.o
++obj-$(CONFIG_RED_15W_REV1)	+= red15w_rev1.o
+ obj-$(CONFIG_STX_GP3)	  += stx_gp3.o
+ obj-$(CONFIG_TQM85xx)	  += tqm85xx.o
+ obj-$(CONFIG_TL_WDR4900_V1) += tl_wdr4900_v1.o
diff --git a/target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch b/target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch
new file mode 100644
index 0000000000..2e103fd1b3
--- /dev/null
+++ b/target/linux/mpc85xx/patches-4.19/103-powerpc-85xx-red-15w-rev1.patch
@@ -0,0 +1,33 @@
+Index: linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
+===================================================================
+--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Kconfig
++++ linux-4.14.90/arch/powerpc/platforms/85xx/Kconfig
+@@ -173,6 +173,16 @@ config XES_MPC85xx
+ 	  Manufacturer: Extreme Engineering Solutions, Inc.
+ 	  URL: <http://www.xes-inc.com/>
+ 
++config RED_15W_REV1
++	bool "Sophos RED 15w Rev.1"
++	select DEFAULT_UIMAGE
++	select ARCH_REQUIRE_GPIOLIB
++	select GPIO_MPC8XXX
++	help
++	  This option enables support for the Sophos RED 15w Rev.1 board.
++
++	  This board is a wireless VPN router with a Freescale P1010 SoC.
++
+ config STX_GP3
+ 	bool "Silicon Turnkey Express GP3"
+ 	help
+Index: linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
+===================================================================
+--- linux-4.14.90.orig/arch/powerpc/platforms/85xx/Makefile
++++ linux-4.14.90/arch/powerpc/platforms/85xx/Makefile
+@@ -25,6 +25,7 @@ obj-$(CONFIG_P1023_RDB)   += p1023_rdb.o
+ obj-$(CONFIG_TWR_P102x)   += twr_p102x.o
+ obj-$(CONFIG_CORENET_GENERIC)   += corenet_generic.o
+ obj-$(CONFIG_FB_FSL_DIU)	+= t1042rdb_diu.o
++obj-$(CONFIG_RED_15W_REV1)	+= red15w_rev1.o
+ obj-$(CONFIG_STX_GP3)	  += stx_gp3.o
+ obj-$(CONFIG_TQM85xx)	  += tqm85xx.o
+ obj-$(CONFIG_TL_WDR4900_V1) += tl_wdr4900_v1.o
-- 
2.20.1


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list