[OpenWrt-Devel] openwrt-devel Digest, Vol 31, Issue 43
Joe Ayers
joe at ayerscasa.com
Mon Nov 19 22:40:34 EST 2018
> I've just added few more commits, so the Git history should looks like this:
>
> fb4f264 fixup! WIP: ath79: Add support for Ubiquiti Nanostation M (XW)
> 12a0c28 fixup! WIP: ath79: Add support for Ubiquiti Nanostation M (XW)
> 1c2f603 fixup! ath79: Add support for Ubiquity Bullet M (XW)
> 68117cf ath79: gmac: ar934x: Add parser for mii-gmac0-slave
> 327012a ar71xx: ubnt-(xm,xw): add rssileds package
> 894e210 ar71xx: ubnt-(xm,xw): create RSSI monitor on wlan0
> f6a7c2c ath79: ubnt-xw: Add rssileds kernel package
> d7889e4 WIP: ath79: Add support for Ubiquiti Nanostation M (XW)
> b246a16 ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method
> 362c66c ath79: Add support for Ubiquity Bullet M (XW)
> 48d8d46 wireguard: bump to 0.0.20181119
>
> Can you please kindly test it on your Nanostation M5 XW? Thanks!
>
Nanostation M5 XW test results:
1) Physical ports not functional. frames are TX out, but RX not
received back. Switch configured out-of-box OK.
2) wlan0 is functional and works correctly. However, default for
wifi-device is option disabled = '1', so not live on firstboot.
br-lan Link encap:Ethernet HWaddr 04:18:D6:A7:70:B5
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::618:d6ff:fea7:70b5/64 Scope:Link
inet6 addr: fdef:fc9:40cc::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:152 errors:0 dropped:0 overruns:0 frame:0
TX packets:126 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:11678 (11.4 KiB) TX bytes:21356 (20.8 KiB)
eth0.1 Link encap:Ethernet HWaddr 04:18:D6:A7:70:B5
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3222 (3.1 KiB)
eth0.2 Link encap:Ethernet HWaddr 04:18:D6:A7:70:B5
inet6 addr: fe80::618:d6ff:fea7:70b5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:365 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:119894 (117.0 KiB)
wlan0 Link encap:Ethernet HWaddr 04:18:D6:A6:70:B5
inet6 addr: fe80::618:d6ff:fea6:70b5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:151 errors:0 dropped:0 overruns:0 frame:0
TX packets:137 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13786 (13.4 KiB) TX bytes:24044 (23.4 KiB)
[ 0.000000] Linux version 4.14.81 (aredn at 59be1430a33c) (gcc version 7.3.0 (Op
enWrt GCC 7.3.0 r8480-fb4f264)) #0 Mon Nov 19 23:28:24 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] MIPS: machine is Ubiquiti Nano-M (XW)
[ 0.000000] SoC: Atheros AR9342 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 805094a0, node_mem_map 8100760
0
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with
crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jff
s2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 58276K/65536K available (3728K kernel code, 148K rwdata,
900K rodata, 1232K init, 204K bss, 7260K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 535.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i
dle_ns: 7144898866 ns
[ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 80279
76190ns
[ 0.008326] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.094952] pid_max: default: 32768 minimum: 301
[ 0.100095] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.107154] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.119431] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
x_idle_ns: 19112604462750000 ns
[ 0.129944] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.136546] pinctrl core: initialized pinctrl subsystem
[ 0.143274] NET: Registered protocol family 16
[ 0.175979] clocksource: Switched to clocksource MIPS
[ 0.182628] NET: Registered protocol family 2
[ 0.188167] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.195602] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.202438] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.209379] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.215616] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.222654] NET: Registered protocol family 1
[ 0.227376] PCI: CLS 0 bytes, default 32
[ 0.232492] Crashlog allocated RAM at address 0x3f00000
[ 0.239697] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.252292] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.258558] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[ 0.279869] io scheduler noop registered
[ 0.284047] io scheduler deadline registered (default)
[ 0.292111] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[ 0.300681] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.308362] console [ttyS0] disabled
[ 0.312216] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 250
0000) is a 16550A
[ 0.321461] console [ttyS0] enabled
[ 0.328883] bootconsole [early0] disabled
[ 0.348691] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.353710] 5 fixed-partitions partitions found on MTD device spi0.0
[ 0.360208] Creating 5 MTD partitions on "spi0.0":
[ 0.365078] 0x000000000000-0x000000040000 : "u-boot"
[ 0.371154] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.377533] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.395387] 2 uimage-fw partitions found on MTD device firmware
[ 0.401457] 0x000000050000-0x0000001e0000 : "kernel"
[ 0.407391] 0x0000001e0000-0x0000007b0000 : "rootfs"
[ 0.413266] mtd: device 4 (rootfs) set to be root filesystem
[ 0.419106] 1 squashfs-split partitions found on MTD device rootfs
[ 0.425386] 0x0000003e0000-0x0000007b0000 : "rootfs_data"
[ 0.431779] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.437503] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.444718] libphy: Fixed MDIO Bus: probed
[ 0.786402] libphy: ag71xx_mdio: probed
[ 0.793193] switch0: Atheros AR8236 rev. 1 switch registered on mdio-bus.0
[ 1.137115] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:04 [uid=004dd
043, driver=Atheros AR8216/AR8236/AR8316]
[ 1.148755] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.157454] NET: Registered protocol family 10
[ 1.167066] Segment Routing with IPv6
[ 1.170900] NET: Registered protocol family 17
[ 1.175456] 8021q: 802.1Q VLAN Support v1.8
[ 1.186162] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.201360] Freeing unused kernel memory: 1232K
[ 1.205986] This architecture does not have kernel memory protection.
[ 1.875083] init: Console is alive
[ 1.878894] init: - watchdog -
[ 2.435983] random: fast init done
[ 2.856676] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.994398] usbcore: registered new interface driver usbfs
[ 3.000130] usbcore: registered new interface driver hub
[ 3.005632] usbcore: registered new device driver usb
[ 3.018258] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.027022] ehci-platform: EHCI generic platform driver
[ 3.033286] kmodloader: done loading kernel modules from /etc/modules-boot.d/
*
[ 3.051197] init: - preinit -
[ 4.078418] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.258341] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.508603] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.384321] urandom_read: 4 callbacks suppressed
[ 5.384331] random: procd: uninitialized urandom read (4 bytes read)
[ 5.402940] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.409028] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 7.457375] eth0: link up (100Mbps/Full duplex)
[ 7.462013] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.468824] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 8.716378] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 8.753955] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.895203] procd: - early -
[ 8.899393] procd: - watchdog -
[ 9.536001] eth0: link down
[ 9.540307] procd: - watchdog -
[ 9.543825] procd: - ubus -
[ 9.581232] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.597920] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.606277] procd: - init -
[ 10.076749] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.089040] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.108051] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca
7fbc85
[ 10.115826] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
[ 10.126266] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.142217] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 10.221617] xt_time: kernel timezone is -0000
[ 10.300010] PPP generic driver version 2.4.2
[ 10.307395] NET: Registered protocol family 24
[ 10.363132] ath: EEPROM regdomain: 0x2a
[ 10.363142] ath: EEPROM indicates we should expect a direct regpair map
[ 10.363163] ath: Country alpha2 being used: US
[ 10.363168] ath: Regpair used: 0x2a
[ 10.378958] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.381105] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=11
[ 10.422741] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 20.236564] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 20.243567] jffs2_build_filesystem(): unlocking the mtd device...
[ 20.243573] done.
[ 20.251859] jffs2_build_filesystem(): erasing all blocks after the end marker
...
[ 26.242591] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.257597] eth0: link up (100Mbps/Full duplex)
[ 26.262217] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 26.340773] br-lan: port 1(eth0.1) entered blocking state
[ 26.346335] br-lan: port 1(eth0.1) entered disabled state
[ 26.352188] device eth0.1 entered promiscuous mode
[ 26.357110] device eth0 entered promiscuous mode
[ 26.436135] br-lan: port 1(eth0.1) entered blocking state
[ 26.441628] br-lan: port 1(eth0.1) entered forwarding state
[ 26.447535] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 27.296297] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 48.676217] done.
[ 48.678226] jffs2: notice: (990) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
[ 49.026973] overlayfs: upper fs does not support tmpfile.
[ 86.463506] br-lan: port 1(eth0.1) entered disabled state
[ 86.588528] device eth0.1 left promiscuous mode
[ 86.593144] device eth0 left promiscuous mode
[ 86.597811] br-lan: port 1(eth0.1) entered disabled state
[ 86.615933] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 87.696152] eth0: link down
[ 91.889971] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 91.897359] eth0: link up (100Mbps/Full duplex)
[ 91.901982] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 91.929642] br-lan: port 1(eth0.1) entered blocking state
[ 91.935133] br-lan: port 1(eth0.1) entered disabled state
[ 91.941215] device eth0.1 entered promiscuous mode
[ 91.946127] device eth0 entered promiscuous mode
[ 91.965818] br-lan: port 1(eth0.1) entered blocking state
[ 91.971374] br-lan: port 1(eth0.1) entered forwarding state
[ 91.977397] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 92.896392] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 95.503349] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 95.534276] br-lan: port 2(wlan0) entered blocking state
[ 95.539768] br-lan: port 2(wlan0) entered disabled state
[ 95.545547] device wlan0 entered promiscuous mode
[ 95.598546] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 95.605229] br-lan: port 2(wlan0) entered blocking state
[ 95.610697] br-lan: port 2(wlan0) entered forwarding state
[ 103.846973] random: crng init done
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list