[OpenWrt-Devel] [PATCH] ath79: Add support for TL-WR740N/NDv2,TL-MR3220v1,TL-MR3420v1
Deoptim
dioptimizer at hotmail.com
Tue Jun 26 10:01:47 EDT 2018
Its common AP99(AR7241) platform with following devices:
TP-Link TL-WR740N/ND v2 (SoC AR7241 / Wifi AR9287 / without USB)
TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support)
TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support)
File ar7241_ap99.dtsi have common architecture with those devices
and dts files include it as common configuration.
Signed-off-by: Deoptim <dioptimizer at hotmail.com>
---
.../ath79/base-files/etc/board.d/02_network | 7 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 +
target/linux/ath79/dts/ar7241_ap99.dtsi | 144 ++++++++++++++++++
.../linux/ath79/dts/ar7241_tl-mr3220-v1.dts | 108 +++++++++++++
.../linux/ath79/dts/ar7241_tl-mr3420-v1.dts | 44 ++++++
target/linux/ath79/dts/ar7241_tl-wr841-v7.dts | 12 ++
target/linux/ath79/image/tiny-tp-link.mk | 29 ++++
7 files changed, 347 insertions(+)
create mode 100644 target/linux/ath79/dts/ar7241_ap99.dtsi
create mode 100644 target/linux/ath79/dts/ar7241_tl-mr3220-v1.dts
create mode 100644 target/linux/ath79/dts/ar7241_tl-mr3420-v1.dts
create mode 100644 target/linux/ath79/dts/ar7241_tl-wr841-v7.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index e2a45b0526..689ae82ffb 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -98,6 +98,13 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "3:lan:1" "5:lan:2" "4:wan"
;;
+ "tplink,tl-wr841-v7"|\
+ "tplink,tl-mr3220-v1"|\
+ "tplink,tl-mr3420-v1")
+ ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
+ ucidef_add_switch "switch0" \
+ "0 at eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
+ ;;
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 7023fa5e58..e5e2b1f8d3 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -54,6 +54,9 @@ case "$FIRMWARE" in
"tplink,tl-wdr4300")
ath9k_eeprom_extract "art" 20480 1088
;;
+ "tplink,tl-wr841-v7"|\
+ "tplink,tl-mr3220-v1"|\
+ "tplink,tl-mr3420-v1"|\
"netgear,wnr612-v2"|\
"on,n150r"|\
"tplink,tl-wr740n-v2"|\
diff --git a/target/linux/ath79/dts/ar7241_ap99.dtsi b/target/linux/ath79/dts/ar7241_ap99.dtsi
new file mode 100644
index 0000000000..d3834b4915
--- /dev/null
+++ b/target/linux/ath79/dts/ar7241_ap99.dtsi
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7241.dtsi"
+
+/ {
+ aliases {
+ led-status = &led_system;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x2000000>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ qss {
+ label = "qss";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_system: system {
+ label = "tp-link:green:system";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ qss {
+ label = "tp-link:green:qss";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ ath9k-leds {
+ compatible = "gpio-leds";
+
+ wlan {
+ label = "ath9k-phy0";
+ gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ reg = <0x0 0x20000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ firmware: partition at 20000 {
+ reg = <0x20000 0x3d0000>;
+ label = "firmware";
+ };
+
+ art: partition at 3f0000 {
+ reg = <0x3f0000 0x10000>;
+ label = "art";
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ ath9k: wifi at 0 {
+ reg = <0x0000 0 0 0 0>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ qca,no-eeprom;
+ mtd-mac-address = <&uboot 0x1fc00>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&uboot 0x1fc00>;
+ mtd-mac-address-increment = <(-1)>;
+ phy-handle = <&phy4>;
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&uboot 0x1fc00>;
+ mtd-mac-address-increment = <1>;
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+ phy-mode = "mii";
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/ar7241_tl-mr3220-v1.dts b/target/linux/ath79/dts/ar7241_tl-mr3220-v1.dts
new file mode 100644
index 0000000000..a5d577749e
--- /dev/null
+++ b/target/linux/ath79/dts/ar7241_tl-mr3220-v1.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar7241_ap99.dtsi"
+
+/ {
+ compatible = "tplink,tl-mr3220-v1", "qca,ar7241";
+ model = "TP-Link TL-MR3220 v1";
+
+ usb-leds {
+ compatible = "gpio-leds";
+
+ led3g {
+ label = "tp-link:green:3g";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ trigger-sources = <&hub_port>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ ath9k-leds {
+ compatible = "gpio-leds";
+
+ wlan {
+ label = "ath9k-phy0";
+ gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ reg_usb_vbus: reg_usb_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <2>;
+ // First value is default pin for flash, second value
+ // (via comma) the GPIO number for sdcard. But we used
+ // gpio 2 and it equivalent of internal CS0 line. And
+ // we use it because we use common bus SPI0.0 for two
+ // devices (default Low polarity chip-select, custom
+ // High polarity chip-select).
+ // In its core, this is a dummy, because internal CS0 line
+ // is locked by HW and SPI driver, and we can not use it at all.
+ // We use this to simply switch SPI bus to another device.
+ cs-gpios = <0>, <&gpio 2 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ reg = <0x0 0x20000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ firmware: partition at 20000 {
+ reg = <0x20000 0x3d0000>;
+ label = "firmware";
+ };
+
+ art: partition at 3f0000 {
+ reg = <0x3f0000 0x10000>;
+ label = "art";
+ read-only;
+ };
+ };
+ };
+
+ sdcard at 0 {
+ compatible = "mmc-spi-slot";
+ reg = <1>;
+ spi-max-frequency = <25000000>;
+ voltage-ranges = <3200 3400>;
+ };
+};
+
+&usb {
+ vbus-supply = <®_usb_vbus>;
+ status = "okay";
+
+ hub_port: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/ar7241_tl-mr3420-v1.dts b/target/linux/ath79/dts/ar7241_tl-mr3420-v1.dts
new file mode 100644
index 0000000000..de2a237d06
--- /dev/null
+++ b/target/linux/ath79/dts/ar7241_tl-mr3420-v1.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar7241_ap99.dtsi"
+
+/ {
+ compatible = "tplink,tl-mr3420-v1", "qca,ar7241";
+ model = "TP-Link TL-MR3420 v1";
+
+ usb-leds {
+ compatible = "gpio-leds";
+
+ led3g {
+ label = "tp-link:green:3g";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ trigger-sources = <&hub_port>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ reg_usb_vbus: reg_usb_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&usb {
+ vbus-supply = <®_usb_vbus>;
+ status = "okay";
+
+ hub_port: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/ar7241_tl-wr841-v7.dts b/target/linux/ath79/dts/ar7241_tl-wr841-v7.dts
new file mode 100644
index 0000000000..ecf0fb5577
--- /dev/null
+++ b/target/linux/ath79/dts/ar7241_tl-wr841-v7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7241_ap99.dtsi"
+
+/ {
+ compatible = "tplink,tl-wr841-v7", "qca,ar7241";
+ model = "TP-LINK TL-WR841N/ND v7";
+};
\ No newline at end of file
diff --git a/target/linux/ath79/image/tiny-tp-link.mk b/target/linux/ath79/image/tiny-tp-link.mk
index 1dfed48dba..e4d07143ed 100644
--- a/target/linux/ath79/image/tiny-tp-link.mk
+++ b/target/linux/ath79/image/tiny-tp-link.mk
@@ -39,3 +39,32 @@ define Device/tl-wr740n-v2
SUPPORTED_DEVICES := tplink,tl-wr740n-v2 tl-wr740n-v2
endef
TARGET_DEVICES += tl-wr740n-v2
+
+define Device/tl-wr841-v7
+ $(Device/tplink-4m)
+ ATH_SOC := ar7241
+ DEVICE_TITLE := TP-LINK TL-WR841N/ND v7
+ TPLINK_HWID := 0x08410007
+ SUPPORTED_DEVICES := tplink,tl-wr841-v7 tl-wr841-v7
+endef
+TARGET_DEVICES += tl-wr841-v7
+
+define Device/tl-mr3220-v1
+ $(Device/tplink-4m)
+ ATH_SOC := ar7241
+ DEVICE_TITLE := TP-Link TL-MR3220 v1
+ TPLINK_HWID := 0x32200001
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+ SUPPORTED_DEVICES := tplink,tl-mr3220-v1 tl-mr3220-v1
+endef
+TARGET_DEVICES += tl-mr3220-v1
+
+define Device/tl-mr3420-v1
+ $(Device/tplink-4m)
+ ATH_SOC := ar7241
+ DEVICE_TITLE := TP-Link TL-MR3420 v1
+ TPLINK_HWID := 0x34200001
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+ SUPPORTED_DEVICES := tplink,tl-mr3420-v1 tl-mr3420-v1
+endef
+TARGET_DEVICES += tl-mr3420-v1
--
2.17.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list