[OpenWrt-Devel] [PATCH 3/3] uboot-sunxi: update Orange Pi R1 and Zero Plus

Hauke Mehrtens hauke at hauke-m.de
Sat Jun 9 12:40:17 EDT 2018


The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.

Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
 ...i-h3-Sync-OTG-and-HCI-nodes-from-Linux-DT.patch |  63 ++++++
 .../320-sunxi-Add-support-for-Orange-Pi-R1.patch   |  58 +++--
 .../patches/400-ARM-dts-orange-pi-zero-plus.patch  | 234 ++++++++++++++-------
 3 files changed, 257 insertions(+), 98 deletions(-)
 create mode 100644 package/boot/uboot-sunxi/patches/310-sunxi-h3-Sync-OTG-and-HCI-nodes-from-Linux-DT.patch

diff --git a/package/boot/uboot-sunxi/patches/310-sunxi-h3-Sync-OTG-and-HCI-nodes-from-Linux-DT.patch b/package/boot/uboot-sunxi/patches/310-sunxi-h3-Sync-OTG-and-HCI-nodes-from-Linux-DT.patch
new file mode 100644
index 0000000000..97aad78796
--- /dev/null
+++ b/package/boot/uboot-sunxi/patches/310-sunxi-h3-Sync-OTG-and-HCI-nodes-from-Linux-DT.patch
@@ -0,0 +1,63 @@
+From 96c04aab58e351fa9ed7e95783018d6dbf60768f Mon Sep 17 00:00:00 2001
+From: Jun Nie <jun.nie at linaro.org>
+Date: Mon, 7 May 2018 13:03:40 +0530
+Subject: sunxi: h3: Sync OTG and HCI nodes from Linux DT
+
+Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
+or MUSB controller.
+
+Signed-off-by: Jun Nie <jun.nie at linaro.org>
+Reviewed-by: Jagan Teki <jagan at openedev.com>
+Acked-by: Jun Nie <jun.nie at linaro.org>
+---
+ arch/arm/dts/sun8i-h3.dtsi | 32 ++++++++++++++++++++++++++++++++
+ 1 file changed, 32 insertions(+)
+
+--- a/arch/arm/dts/sun8i-h3.dtsi
++++ b/arch/arm/dts/sun8i-h3.dtsi
+@@ -219,6 +219,19 @@
+ 			#size-cells = <0>;
+ 		};
+ 
++		usb_otg: usb at 1c19000 {
++			compatible = "allwinner,sun8i-h3-musb";
++			reg = <0x01c19000 0x400>;
++			clocks = <&ccu CLK_BUS_OTG>;
++			resets = <&ccu RST_BUS_OTG>;
++			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
++			interrupt-names = "mc";
++			phys = <&usbphy 0>;
++			phy-names = "usb";
++			extcon = <&usbphy 0>;
++			status = "disabled";
++		};
++
+ 		usbphy: phy at 01c19400 {
+ 			compatible = "allwinner,sun8i-h3-usb-phy";
+ 			reg = <0x01c19400 0x2c>,
+@@ -251,6 +264,25 @@
+ 			#phy-cells = <1>;
+ 		};
+ 
++		ehci0: usb at 1c1a000 {
++			compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
++			reg = <0x01c1a000 0x100>;
++			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
++			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
++			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
++			status = "disabled";
++		};
++
++		ohci0: usb at 1c1a400 {
++			compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
++			reg = <0x01c1a400 0x100>;
++			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
++			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
++				 <&ccu CLK_USB_OHCI0>;
++			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
++			status = "disabled";
++		};
++
+ 		ehci1: usb at 01c1b000 {
+ 			compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ 			reg = <0x01c1b000 0x100>;
diff --git a/package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch b/package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch
index 193b2e480c..97c4769468 100644
--- a/package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch
+++ b/package/boot/uboot-sunxi/patches/320-sunxi-Add-support-for-Orange-Pi-R1.patch
@@ -1,18 +1,32 @@
-From 068fb0d5728c5ec93cb961718d59e7c718886edd Mon Sep 17 00:00:00 2001
+From fd3736abbe57a819312c8df96d14ec396b074581 Mon Sep 17 00:00:00 2001
 From: Hauke Mehrtens <hauke at hauke-m.de>
 Date: Tue, 26 Sep 2017 22:16:59 +0200
-Subject: sunxi: Add support for Orange Pi R1
+Subject: sun8i: h2: Add initial Orange Pi R1
 
-The device tree files are also submitted for inclusion into the Linux
-kernel.
+Orange Pi R1 is an open-source single-board computer using the
+Allwinner H2+ SOC.
+
+H2+ Orange Pi R1 has
+ - Quad-core Cortex-A7
+ - 256MB DDR3
+ - micrSD slot
+ - 128MBit SPI Nor flash
+ - Debug TTL UART
+ - 100MBit/s Ethernet (H2+)
+ - 100MBit/s Ethernet (RTL8152B)
+ - Wifi (RTL8189ETV)
+ - USB 2.0 OTG + power supply
+This board is very similar to the Orange Pi Zero.
+
+The device tree file is copied from the Linux kernel 4.18.
 
 Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
 ---
- arch/arm/dts/Makefile                      |  1 +
- arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts | 77 ++++++++++++++++++++++++++++++
- board/sunxi/MAINTAINERS                    |  5 ++
- configs/orangepi_r1_defconfig              | 26 ++++++++++
- 4 files changed, 109 insertions(+)
+ arch/arm/dts/Makefile                      |   1 +
+ arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts | 101 +++++++++++++++++++++++++++++
+ board/sunxi/MAINTAINERS                    |   5 ++
+ configs/orangepi_r1_defconfig              |  16 +++++
+ 4 files changed, 123 insertions(+)
  create mode 100644 arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
  create mode 100644 configs/orangepi_r1_defconfig
 
@@ -28,7 +42,7 @@ Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
  	sun8i-h3-libretech-all-h3-cc.dtb \
 --- /dev/null
 +++ b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
-@@ -0,0 +1,91 @@
+@@ -0,0 +1,101 @@
 +/*
 + * Copyright (C) 2017 Icenowy Zheng <icenowy at aosc.xyz>
 + *
@@ -87,8 +101,8 @@ Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
 +	 */
 +	reg_vcc_usb_eth: reg-vcc-usb-ethernet {
 +		compatible = "regulator-fixed";
-+		regulator-min-microvolt = <5000000>;
-+		regulator-max-microvolt = <5000000>;
++		regulator-min-microvolt = <3300000>;
++		regulator-max-microvolt = <3300000>;
 +		regulator-name = "vcc-usb-ethernet";
 +		enable-active-high;
 +		gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
@@ -99,6 +113,16 @@ Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
 +	};
 +};
 +
++/*
++&spi0 {
++	status = "okay";
++
++	flash at 0 {
++		compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
++	};
++};
++*/
++
 +&ohci1 {
 +	/*
 +	 * RTL8152B USB-Ethernet adapter is connected to USB1,
@@ -136,22 +160,20 @@ Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
  S:	Maintained
 --- /dev/null
 +++ b/configs/orangepi_r1_defconfig
-@@ -0,0 +1,18 @@
+@@ -0,0 +1,16 @@
 +CONFIG_ARM=y
 +CONFIG_ARCH_SUNXI=y
-+CONFIG_SPL_SPI_FLASH_SUPPORT=y
++CONFIG_SPL=y
 +CONFIG_MACH_SUN8I_H3=y
 +CONFIG_DRAM_CLK=624
 +CONFIG_DRAM_ZQ=3881979
 +CONFIG_DRAM_ODT_EN=y
 +# CONFIG_VIDEO_DE2 is not set
++CONFIG_SPL_SPI_SUNXI=y
 +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-orangepi-r1"
 +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 +CONFIG_CONSOLE_MUX=y
-+CONFIG_SPL=y
-+# CONFIG_CMD_IMLS is not set
 +# CONFIG_CMD_FLASH is not set
-+# CONFIG_CMD_FPGA is not set
-+CONFIG_SPL_SPI_SUNXI=y
 +CONFIG_SUN8I_EMAC=y
 +CONFIG_USB_EHCI_HCD=y
++CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
diff --git a/package/boot/uboot-sunxi/patches/400-ARM-dts-orange-pi-zero-plus.patch b/package/boot/uboot-sunxi/patches/400-ARM-dts-orange-pi-zero-plus.patch
index 731835eb6f..e1e16d6f34 100644
--- a/package/boot/uboot-sunxi/patches/400-ARM-dts-orange-pi-zero-plus.patch
+++ b/package/boot/uboot-sunxi/patches/400-ARM-dts-orange-pi-zero-plus.patch
@@ -1,3 +1,34 @@
+From fd576a3c594ee2356b50a0738403e5cef094935a Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <hauke at hauke-m.de>
+Date: Sat, 9 Jun 2018 15:16:42 +0200
+Subject: sun50i: h5: Add initial Orange Pi Zero Plus support
+
+Orange Pi Zero Plus is an open-source single-board computer
+using the Allwinner H5 SOC.
+
+H5 Orangepi Zero Plus has
+ - Quad-core Cortex-A53
+ - 512MB DDR3
+ - micrSD slot
+ - 16MBit SPI Nor flash
+ - Debug TTL UART
+ - 1GBit/s Ethernet (RTL8211E)
+ - Wifi (RTL8189FTV)
+ - USB 2.0 Host
+ - USB 2.0 OTG + power supply
+
+The device tree file is copied from the Linux kernel 4.18.
+
+Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
+---
+ arch/arm/dts/Makefile                         |   1 +
+ arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts | 145 ++++++++++++++++++++++++++
+ board/sunxi/MAINTAINERS                       |   5 +
+ configs/orangepi_zero_plus_defconfig          |  16 +++
+ 4 files changed, 167 insertions(+)
+ create mode 100644 arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
+ create mode 100644 configs/orangepi_zero_plus_defconfig
+
 --- a/arch/arm/dts/Makefile
 +++ b/arch/arm/dts/Makefile
 @@ -372,6 +372,7 @@ dtb-$(CONFIG_MACH_SUN8I_V3S) += \
@@ -9,84 +40,36 @@
  	sun50i-h5-orangepi-prime.dtb \
  	sun50i-h5-orangepi-zero-plus2.dtb
 --- /dev/null
-+++ b/configs/orangepi_zero_plus_defconfig
-@@ -0,0 +1,19 @@
-+CONFIG_ARM=y
-+CONFIG_ARCH_SUNXI=y
-+CONFIG_MACH_SUN50I_H5=y
-+CONFIG_DRAM_CLK=624
-+CONFIG_DRAM_ZQ=3881977
-+CONFIG_MACPWR="PD6"
-+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
-+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-zero-plus"
-+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-+CONFIG_SPL=y
-+# CONFIG_CMD_IMLS is not set
-+# CONFIG_CMD_FLASH is not set
-+# CONFIG_CMD_FPGA is not set
-+# CONFIG_SPL_DOS_PARTITION is not set
-+# CONFIG_SPL_ISO_PARTITION is not set
-+# CONFIG_SPL_EFI_PARTITION is not set
-+CONFIG_SPL_SPI_SUNXI=y
-+CONFIG_SUN8I_EMAC=y
-+CONFIG_USB_EHCI_HCD=y
---- /dev/null
 +++ b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
-@@ -0,0 +1,113 @@
+@@ -0,0 +1,145 @@
 +/*
-+ * Copyright (C) 2017 Antony Antony <antony at phenome.org>
-+ * Copyright (c) 2016 ARM Ltd.
-+ *
-+ * This file is dual-licensed: you can use it either under the terms
-+ * of the GPL or the X11 license, at your option. Note that this dual
-+ * licensing only applies to this file, and not this project as a
-+ * whole.
-+ *
-+ *  a) This library is free software; you can redistribute it and/or
-+ *     modify it under the terms of the GNU General Public License as
-+ *     published by the Free Software Foundation; either version 2 of the
-+ *     License, or (at your option) any later version.
-+ *
-+ *     This library is distributed in the hope that it will be useful,
-+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ *     GNU General Public License for more details.
-+ *
-+ * Or, alternatively,
++ * Copyright (C) 2016 ARM Ltd.
++ * Copyright (C) 2018 Hauke Mehrtens <hauke at hauke-m.de>
 + *
-+ *  b) Permission is hereby granted, free of charge, to any person
-+ *     obtaining a copy of this software and associated documentation
-+ *     files (the "Software"), to deal in the Software without
-+ *     restriction, including without limitation the rights to use,
-+ *     copy, modify, merge, publish, distribute, sublicense, and/or
-+ *     sell copies of the Software, and to permit persons to whom the
-+ *     Software is furnished to do so, subject to the following
-+ *     conditions:
-+ *
-+ *     The above copyright notice and this permission notice shall be
-+ *     included in all copies or substantial portions of the Software.
-+ *
-+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
-+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
-+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
-+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
-+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
-+ *     OTHER DEALINGS IN THE SOFTWARE.
++ * SPDX-License-Identifier: (GPL-2.0+ OR X11)
 + */
 +
 +/dts-v1/;
-+
 +#include "sun50i-h5.dtsi"
 +
 +#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/input/input.h>
++#include <dt-bindings/pinctrl/sun4i-a10.h>
 +
 +/ {
 +	model = "Xunlong Orange Pi Zero Plus";
-+	compatible = "xunlong,orangepizero-zero-plus", "allwinner,sun50i-h5";
++	compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5";
++
++	reg_vcc3v3: vcc3v3 {
++		compatible = "regulator-fixed";
++		regulator-name = "vcc3v3";
++		regulator-min-microvolt = <3300000>;
++		regulator-max-microvolt = <3300000>;
++	};
 +
 +	aliases {
++		ethernet0 = &emac;
++		ethernet1 = &rtl8189ftv;
 +		serial0 = &uart0;
 +	};
 +
@@ -94,42 +77,93 @@
 +		stdout-path = "serial0:115200n8";
 +	};
 +
-+	memory {
-+		reg = <0x40000000 0x40000000>;
++	leds {
++		compatible = "gpio-leds";
++
++		pwr {
++			label = "orangepi:green:pwr";
++			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
++			default-state = "on";
++		};
++
++		status {
++			label = "orangepi:red:status";
++			gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
++		};
 +	};
 +
-+	reg_vcc3v3: vcc3v3 {
++	reg_gmac_3v3: gmac-3v3 {
 +		compatible = "regulator-fixed";
-+		regulator-name = "vcc3v3";
++		regulator-name = "gmac-3v3";
 +		regulator-min-microvolt = <3300000>;
 +		regulator-max-microvolt = <3300000>;
++		startup-delay-us = <100000>;
++		enable-active-high;
++		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
 +	};
 +};
 +
++&ehci0 {
++	status = "okay";
++};
++
 +&ehci1 {
 +	status = "okay";
 +};
 +
-+&mmc0 {
-+	compatible = "allwinner,sun50i-h5-mmc",
-+		     "allwinner,sun50i-a64-mmc",
-+		     "allwinner,sun5i-a13-mmc";
++&emac {
 +	pinctrl-names = "default";
-+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
++	pinctrl-0 = <&emac_rgmii_pins>;
++	phy-supply = <&reg_gmac_3v3>;
++	phy-handle = <&ext_rgmii_phy>;
++	phy-mode = "rgmii";
++	status = "okay";
++};
++
++&external_mdio {
++	ext_rgmii_phy: ethernet-phy at 1 {
++		compatible = "ethernet-phy-ieee802.3-c22";
++		reg = <1>;
++	};
++};
++
++&mmc0 {
 +	vmmc-supply = <&reg_vcc3v3>;
 +	bus-width = <4>;
-+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-+	cd-inverted;
++	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 +	status = "okay";
 +};
 +
-+&mmc2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&mmc2_8bit_pins>;
++&mmc1 {
 +	vmmc-supply = <&reg_vcc3v3>;
-+	bus-width = <8>;
++	bus-width = <4>;
 +	non-removable;
-+	cap-mmc-hw-reset;
++	status = "okay";
++
++	/*
++	 * Explicitly define the sdio device, so that we can add an ethernet
++	 * alias for it (which e.g. makes u-boot set a mac-address).
++	 */
++	rtl8189ftv: sdio_wifi at 1 {
++		reg = <1>;
++	};
++};
++
++/*
++&spi0  {
++	status = "okay";
++
++	flash at 0 {
++		#address-cells = <1>;
++		#size-cells = <1>;
++		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
++		reg = <0>;
++		spi-max-frequency = <40000000>;
++	};
++};
++*/
++
++&ohci0 {
 +	status = "okay";
 +};
 +
@@ -143,6 +177,46 @@
 +	status = "okay";
 +};
 +
++&usb_otg {
++	dr_mode = "peripheral";
++	status = "okay";
++};
++
 +&usbphy {
++	/* USB Type-A ports' VBUS is always on */
++	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 +	status = "okay";
 +};
+--- a/board/sunxi/MAINTAINERS
++++ b/board/sunxi/MAINTAINERS
+@@ -327,6 +327,11 @@ M:	Icenowy Zheng <icenowy at aosc.xyz>
+ S:	Maintained
+ F:	configs/orangepi_zero_defconfig
+ 
++ORANGEPI ZERO PLUS BOARD
++M:	Hauke Mehrtens <hauke at hauke-m.de>
++S:	Maintained
++F:	configs/orangepi_zero_plus_defconfig
++
+ ORANGEPI ZERO PLUS 2 BOARD
+ M:	Jagan Teki <jagan at amarulasolutions.com>
+ S:	Maintained
+--- /dev/null
++++ b/configs/orangepi_zero_plus_defconfig
+@@ -0,0 +1,16 @@
++CONFIG_ARM=y
++CONFIG_ARCH_SUNXI=y
++CONFIG_SPL=y
++CONFIG_MACH_SUN50I_H5=y
++CONFIG_DRAM_CLK=624
++CONFIG_DRAM_ZQ=3881977
++CONFIG_MMC0_CD_PIN="PH13"
++CONFIG_MMC_SUNXI_SLOT_EXTRA=2
++CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-zero-plus"
++# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
++# CONFIG_CMD_FLASH is not set
++# CONFIG_SPL_DOS_PARTITION is not set
++# CONFIG_SPL_EFI_PARTITION is not set
++CONFIG_SUN8I_EMAC=y
++CONFIG_USB_EHCI_HCD=y
++CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
-- 
2.11.0


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/listinfo/openwrt-devel



More information about the openwrt-devel mailing list