[OpenWrt-Devel] [PATCH 3/3] ipq806x: add Netgear EX6100v2/EX6150v2 support
Thomas Hebb
tommyhebb at gmail.com
Wed Jan 10 05:15:10 EST 2018
This patch adds support for the Netgear EX6100v2 and EX6150v2 Wi-Fi
range extenders.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256 MiB
FLASH: 16 MiB Winbond W25Q128
ETH: Qualcomm IPQ4018 Gigabit PHY, 1 port
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100v2)
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 2x2 (EX6150v2)
INPUT: Power, WPS, factory reset buttons, AP/extender mode toggle switch
LEDS: Power, router, client (dual color red/green)
Router activity, client activity (blue)
WPS (green)
SERIAL: 3.3V unpopulated serial header connected to ttyMSM0. 11520n8.
Serial access is not required to install OpenWRT on the device.
To access, unscrew the four Torx T10 screws on the back of the
unit and unclip the faceplate. Then, unclip the power supply
board (to which the logic board is mounted using four large
standoffs) from the large clips on the top and bottom that hold
it in place. Flip over the boards so the power supply board is
on top, making sure not to damage the Wi-Fi antenna wires.
Unscrew the four Phillips #1 screws connecting the power supply
board to the standoffs and carefully lift it off, unplugging the
eight-pin connector that supplies power to the logic board. Then
unscrew the four hexagonal standoffs from the logic board, flip
the board over again, and lift off the metal shield (watch out
for thermal compound). The unpopulated header is located at the
bottom edge of the logic board, with pins 1 (square pad), 2, 3,
and 4 carrying VDD (3.3V), TX, RX, and GND respectively.
To install, upload openwrt-ipq806x-EX61x0v2-squashfs-factory.img to the
Netgear web interface as a firmware update and ensure that the listed
update version matches that of the OpenWRT image you're trying to
install. Note that OpenWRT will not bring up the wireless interfaces by
default, so you must be able to connect to Ethernet for initial
configuration.
Features, tested and working:
- Serial
- Flash
- Ethernet
- Wi-Fi, 2.4GHz and 5GHz
- Buttons (WPS and factory reset, which acts as restart)
- LEDs (most of which are driven by a shift register connected to SoC GPIOs)
- Factory OpenWRT install from Netgear firmware
- OpenWRT sysupgrade
Features, untested but should work:
- All above on the EX6150v2. I only own an EX6100v2 and so could not
verify the other device.
Features, not planned:
- AP/extender toggle switch
These two boards are unusual in that they both run the same stock image
and share the same official update binaries. As far as I can tell, the
only difference between the two units is the 5GHz MIMO configuration:
1x1 for the EX6100v2 and 2x2 for the EX6150v2. Since the boards are so
similar, both are supported by a single OpenWRT image, which determines
the board it's running on at runtime by reading the flash. The only
runtime differences between the two boards are the board name, the model
name, and the Wi-Fi calibration data that gets loaded.
U-Boot on this device is device-tree aware, and the stock firmware
provides the kernel and device tree in a FIT image. We do the same
because, even though this version of U-Boot ought to be able to boot a
uImage with appended DTB, I was unable to make that configuration work
for unknown reasons.
The Wi-Fi calibration data (board-2.dat) for both boards was taken from
an official Netgear firmware update.
Signed-off-by: Thomas Hebb <tommyhebb at gmail.com>
---
package/firmware/ipq-wifi/Makefile | 4 +-
package/firmware/ipq-wifi/board-ex6100v2.bin | Bin 0 -> 24276 bytes
package/firmware/ipq-wifi/board-ex6150v2.bin | Bin 0 -> 24276 bytes
.../ipq806x/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 8 +-
.../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 13 ++
target/linux/ipq806x/base-files/lib/ipq806x.sh | 24 +++
target/linux/ipq806x/config-4.9 | 2 +
.../arch/arm/boot/dts/qcom-ipq4019-ex61x0v2.dts | 211 +++++++++++++++++++++
target/linux/ipq806x/image/Makefile | 41 +++-
.../patches-4.9/0069-arm-boot-add-dts-files.patch | 3 +-
11 files changed, 300 insertions(+), 10 deletions(-)
create mode 100644 package/firmware/ipq-wifi/board-ex6100v2.bin
create mode 100644 package/firmware/ipq-wifi/board-ex6150v2.bin
create mode 100644 target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-ex61x0v2.dts
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index f2b705e13a..7d26938e97 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -13,7 +13,7 @@ endef
define Build/Compile
endef
-ALLWIFIBOARDS:=rt-ac58u fritz4040 nbg6617
+ALLWIFIBOARDS:=rt-ac58u fritz4040 nbg6617 ex6100v2 ex6150v2
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
@@ -44,5 +44,7 @@ endef
$(eval $(call generate-ipq-wifi-package,rt-ac58u,ASUS RT-AC58U/RT-ACRH13))
$(eval $(call generate-ipq-wifi-package,fritz4040,AVM FRITZBox 4040))
$(eval $(call generate-ipq-wifi-package,nbg6617,ZyXEL NBG6617))
+$(eval $(call generate-ipq-wifi-package,ex6100v2,Netgear EX6100v2))
+$(eval $(call generate-ipq-wifi-package,ex6150v2,Netgear EX6150v2))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-ex6100v2.bin b/package/firmware/ipq-wifi/board-ex6100v2.bin
new file mode 100644
index 0000000000000000000000000000000000000000..5bb224b244140a1da38b5eaf12cdacf1cccd4fd1
GIT binary patch
literal 24276
zcmeHPTToL;8g7t_7gSCNw<H{Lg at hqd0;3V4gb<kkQ5nVyMAu~ykpx%~6va3t<)9))
zWV|q344{jO3TIuVT%A#ISI3>1(v-U|^XALGP1VZQ)YjI#th3$cBq6~QNJdye&L6t_
z at 5|r)_t$-rbLcPmI6F(8wNan4JYTNekX5Jy)z#GiO3^YD10aE+bYI=-Pb*53ORG)t
z9Tlb;xv6aRaxz!C`_tMolucOy?E+w1KD6U6D=iNQ0P_yB(l(<$lKNm&0>Hx1aHs$P
zV?ioR=ffAB$YiOgD*#ecQ~&+bPe9EM0YCrabfz=RW7AnpUd9IjPsg`vqecS1Kp9`>
zJ-^gd6%J>EUQR(iI`y$Mlh)%qevC-<wUA7*bU}dcc#VxgX>68z3H`Va{1_L_%soWF
zJPJHVfQetSXwi}-ei_g-7Sfcxi=vv=L9}fg;_1Q5fuWWbvnkh@`EsbcxuMLMpS$Ye
z_3q;>wWg1AS3JA{wK`K_?uS1^xphaD2wq(uI@(fcT4&U}ywQEEp~7g$RX at Cjni+F*
zRnXvM%YImvK^Y__fmi)QhZ>5E>AA_!w5ef-Q3sn{>286h`6}tdq3$ycHO4~Ka)&{p
zr+<^=8lX(l#Iu?)@Wg{Y_dcLRKeO3Y`lPS&vpn<iEm4_+J$211%OsmP`46t|>C8DU
zt&J(^ys@=&)p34Z#HaTzm=5Jviq=JG?p at k_ETckJ%r!i{*6`(q<BGbt9betp-?{Fj
zd_S-JNl(q8oSnkli1f$(yPNWMCv1w+UA<!J(6 at ZBpIdQnsJ?gE;rN<}lG%k4<E;~c
z;Lrt&7B9sjBBNuuaq-S~{IL|h$Bv29$|Hq0L;wT?1O^5Mpm^TA;Naj8hlJj3tI$Zl
zJyIZLi^U at NClLw+BB4Mi+#EC?IPOq9dSf!via=Xief`Fbh8z`Gv?wHm8cHRTh=js;
zm|=(h=jYe2BcVo>p~ASZ(7>Re|B_7u0G&P6%k;%HgYbR?c3*S2br1zK(gzMnPEJme
z!c7&&nHo)sL at eav+^Ny%P{D8v%fhp;6g&m1*>~`8(}~uz9d9UuAeo?K$fc+qa^I!!
zE>L1~DJ-0&U_E1D9Gs)z7{c*zEC$!&T7~wR7R$r)6nO>>uEF%U5?3me&y-j?o~}qY
zEXS8)D%|CS?Gmjz2qX at l2%`V(Rk5qH-_xtkX{yz(8Be2%_qb$ImD}wSdUdRaUN_aP
zZ3G_iDgxu;Tm{#Vjc32g#`5ueMZO^wPkoh&W#Ac#3<F$*6Rl`#xZ?QU-v0jHiDMEq
z3NWuR<&%3%x#k|Dy<2m_Hs~HCZz*G+Ec6=P_3~@W-iLcqW)8lrK7$g2k{1M+t>Fb2
zkK#Frk_Q4zhCzTqfI)ykfI)ykU=AY?t&GOvSsw{M!Zxs03Rhy8tocp>g{5aM-FoaE
zlh4{}9!g>;-Iq98IDU);PVqX%64Wuvm)@y1b9f1vslP7>_<BO%Yr9#7i(y-Zb@({|
zFg;-H8-6}MmCNNaS%O5wkDHkq`X{|CK`i3O&rB@|3h7_m%+z>DIGmW6C|Zp(VeQ1W
zJZS8_=Sggx<DLt}fF=z9D+>#Vg3{(l&pA@*d<>|8ItYLiAi^Mj3KDLFkjLW;YFMrf
zmc7vCefT$RC`=t8JO~4!jlui at SpV|HkKl(Nek4<*qo9H1-#?Z$e*cNAabeR~m}QqY
z<L(3q{Bkpl9T-#wPaxpwa$wN>FQHt7;xxGn<!#CgMexnFZ}>ZJX<~vz{4N7^az~xj
zQKxf;f{jJnO3Es%ZRa{J^z{!6-W<OB;LqQD_uT&qASVcg>-5c`paO;e6~5n+PTEr3
zPcLGx6#}#+XhZ<Wb5H}T*?AI5o`D*)&CXL$^8C}FY<8Z2`VXR4i>XA{|Mi$ci%A!3
zmNf9Xef}R60-EiKiUj^w_;O~ve)IP7*7lw&#GR49dealprA~@M at izKYEx+3`xL at iX
zx*J;V$a(1O*KCZ3^AtP-8|Yr^FavH-7z{d)_Bsty<7$Q4kVf--O%fRt6UV;Hl$-_S
zvzYXj^34%bwNc6_3}@vibFlTS70MOZ8kVsOz25BK`8nrIXUijwzx?`@9{l=$>H-2F
zx&A;K$@Y%ygR?IIATpFf0p3CiV1N<??<wCD(I;>6>mkn|(;0p(zaEbCX#8kz!>>m?
z_woFC<Rcmb_ZWzt=l*N?^{8vF{CXe8^@m>%qNAfd0-MbS?jbBJ4EPZiESOGyy at uV#
ze!>1%WI<G8)XgXlD16G?pv0%Pfc#DdTyKZ?XhhR&P9EDblcw1TZxqcyl-}@>DPRy_
z5MU5^j}Ry+F>a>#^(<ESVrpW3^6N_|`^Ad`f1>Qm%bk64I1%V8ic>5MzuxgMJmh=|
zyYEt5w0f7q at atXZ_{qf|<H7e#s=5*7>D93w7=FDQC*M$5-qthn___1hVthK;TgT`L
zdlg}@rC52R&Gt$n-=?(2joh)dTlN&^s3aq|h<>ZZT&&`u?}T0GNR)!nv-SqUXwz8b
zqv!1wVyjJST}BMs`po9y^{V8NKiSS$s*ANMJ~FU%CMJT>F8fhpm#x6MdbHPmf~c}>
zvdD?AtnKDny-uZs24^i*PJ^D#L>Yk1P7yWMLi38z%l5Ox0c(+2O^jH(&3pB0r7`3P
zmFBIKOSUfLlFi;iR9bY!;?Ya?(?qRxlX(sCwYAe+uh&btBX at 1*Ntfc0OFdmuI6{a0
zb7F^Ojh+Kdn+cOetLGAbwDp>+^;xQA_OFRc)&}zy6$csgcF7XJXuG|UD6ypLV at Esf
zO+=YRt&fF{bXxWm=c{D)J4BbY*1SP4rbduKmrmOc5JeWHo;~`7{UBk48fL#oT!dI^
zRQSu=BNuG@&Dr``Y6Lh3e`E&U>N76+vVaUq3`$-QcptWgm#NL+;@9Nd(T|j%FivL6
zKlsPF?N9d3i9^3xn<D4MhFos0+O|?Dh+8s$Z+lLYY!9b2Eay at G&Qq%`qFvF&e>r==
zm?=+)j0wJd{!nF}R=JEDbGmPHYsx{sdFlG6*Q(BF8YR`S+rRBH6|785hz8(c at 4+g4
zwn82kcXwb<yXJ_jmbK~eb<^3*Mp0GF_9wk{CE67dUQF2i%T>GddR!PDVeMXjG-Yq(
zmc?uDT`N74ewbewx%GjqYFmLWS&Rh at U#hQNs~1WmIW3(Vj-}Pd6o=_=-}vo$)sgt>
z$nC=&dw1lnNft$fT({NN<r<W#NbYcNZEN<S<m#xxZ~u^YGPxnPJbcT|_JigPI+>6a
z(%-rJcLf{eX<XsePE+%meM!3_@~;f+?#gHq)v~u=JzZ0(%MkH+?5;1$cCO7!Rz`A8
zwQl(=%`Du?(%iaUcVYc0>He6V{$S0tWe{Kxm{|zC?XPWwx(m(J9`!Ys6dW+Bl~RdB
z4FBLSZSX|`fl#nHc*gwN2E(tXSvaO>ZX at 99z28)~o7<=(UOmIFpGI!}%w*M%d4*{1
z6R_alIlq1YU?kriz!Y)jH84edcOB%vC#@1 at Q6YX$(ke1s3=c{ndGm-nAKJJO29yT#
zNuE98)(6Y}PV(&$=N{(g_~k#Nr;qsWL6HAm)G_eQbnxG&d-C3R_0IBl$*o6YGyM8~
zm$(ycU4=-Yc&w1DJYE=nz2nT-L8FGryZ!2f^Thg{q+*XvGnVnbucpvKFn(`3^6t!V
ak0#zL7=AqolsiBkI>WD@?oZ8$`~M&E1DN~(
literal 0
HcmV?d00001
diff --git a/package/firmware/ipq-wifi/board-ex6150v2.bin b/package/firmware/ipq-wifi/board-ex6150v2.bin
new file mode 100644
index 0000000000000000000000000000000000000000..930b87053969674534134d0ccf3e5820ccd47d50
GIT binary patch
literal 24276
zcmeHPTToL;8g7t_7gSCNw<H{Lg at g%F0;3V4gb<kkQ5nYzMAtz?B>`3hMKMlEIjD#c
z8BvB?03B3RJnJgu>WqrJI<7ONDR*Dy&6j<f2idZ=wtQJ<yK{0vf+vuuj40<1-Tn99
z{dfQUolbH>f63?BS;<*z^eGGTleMd|R_j1zWhH=8xB%q<NMI`2U9)s^S&6))(v-ZV
z%v6<ZDqXtJQ7hT8xw;fpQx-wL0N9rg{rC$uZw?3mGY+uQ)}b+y`e0TJ!0ga)r~m+S
zK`Ja~!UvtmWT|K<08&#^|MTJnP_sk8%YU87q|yvFo!7)RJ_vX?wpR-|6Zj3v*f#I=
z`L3pLxEl1J1jR_{qh%&-#5eqyksNEbqsY<)0lxDwItQt-S?(74dGGi!FIt&<ihy;L
zc+Lb1zhuswdGq{opy at 26vAqvdRr4U)Hcs)3;Mu^HrY5r~*O>Y2N>^iDsWCry$=yp`
zN1CclpXV;Rdl_mqrq#KhzJzk^hAa_0zjWnLQ at Lq{QS<C_*WtP{qajy)_af?M%*|Cn
zhht59pe=)RNK69H`>*V;D>SC(%AspR-4>$`c01qI1YPr0(z{o>PS#Z!SF08}9TGj`
zo1j()Wr8lA&5VO59`v=30VVpCeOT59edS-}nHR2)${g&eX<S??S<A`4b7^Ns&Jk&K
zOmWBM4IN94 at M|JA-|9B)&o39Ph|=6TyW?<1nXHIwczChy+f_#tHE~<Mzr3eo#j)f)
zyloG9s`lq>73M~y-|yeikhddYZItf9c~iT->61O&vRhYbdlwvtuZk%Cuux*6r4R at X
zoi%6fd at Ld|I+hz3Prc%gmgqHhR46Zx65bF25D*X;7#M)^88d=|gF~DWdb6cWBYkwR
zK*|=2Met7|6bM8 at fl#<EXeMypp?HkOR3;UHmX_MuHERqxDllhGNC-KVN+uBrh4HY$
z4*l=TSFa+WM%s`uE-W-KDCmEVt^t6~pB!cK@~T02KLUrZI?z0b5}N4~r^w~<Bq`if
zah!LfNs)+!e4P7kG&)o;9K*8kEGz|2!K!xeJJ4{nxwZW at We~^*o#Il|PPy$;c-^Gf
zTnY<kDOitL7zgJlIEHXM9E-uVxK^Qkti|&1JVl;CgKIE7uEdoJ<zpq5j;AZq4GZyw
zm<o3VVLMB!4uV92lJjq`im9=P at 90%(nQFCb#gnMwJuaD0<#xG*UL75w*G+Zn8-YhW
zkHEM%SHU%8<Jr%%v3xvVk#9)FQ=g||8F+>w!vHVB(Pp$YTsa)8zrSz%+<_VinAe<)
z$vr1SbI;M<tvYHObWf7El+kw<dX4V+@}{<r;hvOPgD+Q~L5V at h3j)m6 at B)m7d0L|6
zfdErs5MU5s5MU5s5MU6P#t1|!qp^6_XTs00RjkFr#aJe5CM95X$;q?V?z`uX&)RAp
zDq=|8mpocHc8*z;c%5S&8kptF=wzR1d<mJQe=G?2dP3l9zYh!-!^Se}&=UY)x!2k^
z^ki(Al$0csB}hd4xGAe8$r8jOemsnCDr*QoGQKIL at sMyhF)>lJ8fV<r at qKyF+55;7
z_)_zp3dMjX4FD?(3y6Z!;w(=&OX*AusDU~NfD|CYAb$!HZiJA>LnSq|YlCG^wRxZZ
zLmLW9X9^F(Kxln1e*m^Wd-^N*<(FR_CDKvSK>N at 4W%WOQA*-L=Fq%HFr#BPsI0*c9
zHH;k?R0>ZZ;OTN;(9Cb4oPk2Q+=TKrHbWtNaqS!W$y=G2AQ8XMM4sG{XLaQ1oS|S%
z;l|?9GHc7J_U^v^fx)XoH}CxQ$Df|~-vE*bLg6}nb1KN7 at V~+LTha-8iu>tB?6pCF
zwgim`fa4t0z-pvULLFzI25lpC3hFrjG$<RX6Hxy_^y=|0(e?j&`0pX}wizb8U>`^a
zuiNMMXb{kBPh=AK-{8xc at yd0Zwl%l)oF{G!|J|D|K~HsuC=_p_zpKmdb{X8C>K?iq
zTJFes=<HW)jED0SJOdl(Ug<CcZcrEuI*|4%4O8Q4h1!rt^Z8ncXcqGEb6-~KSOpog
z*byxmn=>a{qm)q?&dO2dU at KXRl#8%sEMq5nygoklK1Y=w%10c3`SpuE`1N0Z84v);
z^?O?!Z12cExcXuMB11_O;4P$sUk^YKyr+C!L|?qluZKK?Oe(!8zaGwXZ|rPu!>>m?
z_p$tX6eF4g_n3&D=l-VrdNj0Ge!UO#`opgW(b3T!iOpsM_Y at Wu2K-2~W=$r)Uc>HV
zKV|<rvLLEH>S~k+6h2ihlj2if;P_4kyxvan(TS$pv^=(D7EQAgUNcQWlwOOGF)#=)
z2rvkIL<kfY8`qKidKN2uF1av2`Sr!5|J=EOFG&Aw+o&-)oCx$4#dj<Wzuw8SAEZ8o
z-F7K1TD?nQ`1LMy{N&=3Z1Wx at 6RK`Rd3tqp1cqPl#>qDnqJL`Nc|v`*7+X&C(lK(>
zUO^aaDOTP{qrIHSw<)c0!#8YgmYqd8D#`FQqTgyU7pZvYJ7L}JiBd4qYOf=VHjOoT
z<h0#FY_Msq3y2|GpV?frQY9b$i|wSPvPi4qBL`bYVj>vnv>zh2+X}2pM|$l?i3;0V
zOEU4jwar|u*Qu1yq194BIrMZS$^h(koT##{HZK}EXKy9;S_{o;V%XYc-lbnIjd9FS
zZr(tKWa~sB+3Zb3xkXnb9yx12K~!7UnwJqjSUb$MdcBl8eA9N?5mGz~si#v4XK1&7
zO>D6&({rF}BVn>=^<3i5wqA3kK1;R0{sVE=T4!Fb;vk3KPFVsNX|vZ8#g=q^>_~^b
zfhe`8^|3IJ4$JPMe3i_8gXpwYn^)<@<P0(x(h2)sqR^t$vq!$M?<0&*!|b<+GZ0IS
z3V(KexZAeJoUM-~XMk()N2cJdJ`<8J7mz`TLCFgOAH&x0vb1SzCV!p;<)k*<ptx~#
z{~wm8B=cfJ&NWtST&xtt&6~NaEvG at YlT#9wbFY8v at ue2g_UNL&weB@$CMQJ31YbYB
zzdTQ?T)>Sv(YLNSWgp)>f91oA6(=?IlFHakk2*~SixU%~0l3?{uR@=#NRErUIk2-$
zb5K^zT6_PJsWr1+R1vf3L2pg5c9Db^6L$Mt#df_O7lubzyH*}b*%i5d?($m~OHQUA
z;Fm{kxMQo>SfG=Ov7n)|wbje at LTMzYsbkgQwAz@WF#Yw*U!GPSjIWH`G}OLpOYSnc
zC?e#Nt+poDpj1V2hkC1<v-is at qgFrqQ{FLoUF^2-^;g^WnOEs#LRLtB$BsW1tVvGe
z3NLh+8kg-(+8&XAeqcvuMuVuDz3IY<suEp>h{t1hep9-2d7fMu$vNJ<{;M>za05$o
z?NUwm%Hz^KF<YnGeqq+jAn-9E at V39U5$Y~9z})L=EH2n<R4b(ti5ULDU)tb{1OlO8
zUGS9owGD<}PjlfI)AUBbS8~U@?l-+rN4$E5U;le>^QRQ6ew6EvXzt^%;NLsHegI$&
zzB_;=;>>GciTLh1$bU~-BFrLF{LZ8$j&vqGD8<2>N8I_)`q?m{GMMk+*&}X!u<V}>
zzCGgH!}>IT`cLWQBmR33<i8iT5BxY8{P)RTyf<DwWq+UCdNen~ukUw>JJHr<L<-4c
zg=FQi!tm=U1~o~ehPn5zPB8p>k4=U4m3XYhS$~5D!Pvd&th+PAJ-T>rVEFY8pxgoS
P&>4RHWWQ^UKmPv#T2ht@
literal 0
HcmV?d00001
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index ad357b7363..6587b9309d 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -50,6 +50,10 @@ nbg6817)
ucidef_set_interface_macaddr "lan" "$(macaddr_add $hw_mac_addr 2)"
ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 3)"
;;
+ex6100v2 |\
+ex6150v2)
+ ucidef_set_interface_lan "eth0"
+ ;;
*)
echo "Unsupported hardware. Network interfaces not intialized"
;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 4c5b55bc53..b16b637911 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -47,7 +47,9 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/pre-cal-ahb-a000000.wifi.bin")
case "$board" in
- ap-dk01.1-c1)
+ ap-dk01.1-c1 |\
+ ex6100v2 |\
+ ex6150v2)
ath10kcal_extract "ART" 4096 12064
;;
fritz4040)
@@ -57,7 +59,9 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-ahb-a800000.wifi.bin")
case "$board" in
- ap-dk01.1-c1)
+ ap-dk01.1-c1 |\
+ ex6100v2 |\
+ ex6150v2)
ath10kcal_extract "ART" 20480 12064
;;
fritz4040)
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
index 7884f5117a..0f3231323a 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
@@ -29,6 +29,19 @@ case "$board" in
vr2600v)
echo $(macaddr_add $(mtd_get_mac_binary default-mac 0) $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress
;;
+ ex6100v2 |\
+ ex6150v2)
+ case "$PHYNBR" in
+ 0)
+ # 2.4G
+ echo $(mtd_get_mac_binary dnidata 0) > /sys${DEVPATH}/macaddress
+ ;;
+ 1)
+ # 5G
+ echo $(mtd_get_mac_binary dnidata 12) > /sys${DEVPATH}/macaddress
+ ;;
+ esac
+ ;;
*)
;;
esac
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index c4d2c8f258..1e011292eb 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -7,6 +7,8 @@
IPQ806X_BOARD_NAME=
IPQ806X_MODEL=
+. /lib/functions.sh
+
ipq806x_board_detect() {
local machine
local name
@@ -50,6 +52,28 @@ ipq806x_board_detect() {
*"VR2600v")
name="vr2600v"
;;
+ *"EX61x0v2")
+ # There are two models in this series, which have identical
+ # hardware save for the number of 5G antennas. Since we run
+ # the exact same image on both, we need to check the flash
+ # to distinguish which we're running on.
+ local hw_id="$(dd if="$(find_mtd_part dnidata)" \
+ bs=1 skip=41 count=25 2>/dev/null)"
+
+ case "$hw_id" in
+ *"1x1")
+ name="ex6100v2"
+ IPQ806X_MODEL="Netgear EX6100v2"
+ ;;
+ *"2x2")
+ name="ex6150v2"
+ IPQ806X_MODEL="Netgear EX6150v2"
+ ;;
+ *)
+ name="ex6100v2"
+ IPQ806X_MODEL="Netgear EX61?0v2 (ERROR: failed to parse hw_id)"
+ esac
+ ;;
esac
[ -z "$name" ] && name="unknown"
diff --git a/target/linux/ipq806x/config-4.9 b/target/linux/ipq806x/config-4.9
index bca4264c8f..6ba480d5a3 100644
--- a/target/linux/ipq806x/config-4.9
+++ b/target/linux/ipq806x/config-4.9
@@ -189,6 +189,7 @@ CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GPIOLIB=y
CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_74X164=y
CONFIG_GPIO_SYSFS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDIRQS_SW_RESEND=y
@@ -452,6 +453,7 @@ CONFIG_SPARSE_IRQ=y
CONFIG_SPI=y
# CONFIG_SPI_CADENCE_QUADSPI is not set
CONFIG_SPI_MASTER=y
+CONFIG_SPI_GPIO=y
CONFIG_SPI_QUP=y
CONFIG_SPMI=y
CONFIG_SPMI_MSM_PMIC_ARB=y
diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-ex61x0v2.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-ex61x0v2.dts
new file mode 100644
index 0000000000..a2ae64a1dc
--- /dev/null
+++ b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-ex61x0v2.dts
@@ -0,0 +1,211 @@
+#include "qcom-ipq4019-ap.dk01.1.dtsi"
+#include "qcom-ipq4019-bus.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear EX61x0v2";
+ compatible = "netgear,ex61x0v2", "qcom,ipq4019";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ rsvd at 87E00000 {
+ reg = <0x87E00000 0x0200000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ led-boot = &power_amber;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+ led-upgrade = &power_amber;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ ranges;
+
+ gpio-sck = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <0>;
+
+ led_gpio: led_gpio at 0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ spi-max-frequency = <1000000>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power_amber: power_amber {
+ label = "ex61x0v2:amber:power";
+ gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power_green {
+ label = "ex61x0v2:green:power";
+ gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ right {
+ label = "ex61x0v2:blue:right";
+ gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ left {
+ label = "ex61x0v2:blue:left";
+ gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ client_green {
+ label = "ex61x0v2:green:client";
+ gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ client_red {
+ label = "ex61x0v2:red:client";
+ gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ router_green {
+ label = "ex61x0v2:green:router";
+ gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ router_red {
+ label = "ex61x0v2:red:router";
+ gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "ex61x0v2:green:wps";
+ gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&spi_0 {
+ flash at 0 {
+ compatible = "winbond,w25q128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0 at 0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition1 at 40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition2 at 60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition3 at c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition4 at d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition5 at e0000 {
+ label = "APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition6 at f0000 {
+ label = "APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition7 at 170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition8 at 180000 {
+ label = "config";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+
+ partition9 at 190000 {
+ label = "pot";
+ reg = <0x00190000 0x00010000>;
+ read-only;
+ };
+
+ partition10 at 1a0000 {
+ label = "dnidata";
+ reg = <0x001a0000 0x00010000>;
+ read-only;
+ };
+
+ partition11 at 1b0000 {
+ label = "firmware";
+ reg = <0x001b0000 0x00e10000>;
+ };
+
+ partition12 at fc0000 {
+ label = "language";
+ reg = <0x00fc0000 0x00040000>;
+ read-only;
+ };
+ };
+ };
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 2e6cb0922e..297062d8b2 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -58,7 +58,7 @@ define Device/UbiFit
IMAGE/nand-sysupgrade.tar := sysupgrade-tar | append-metadata
endef
-define Device/DniImage
+define Device/DniNandImage
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
KERNEL_SUFFIX := -uImage
@@ -71,7 +71,21 @@ define Device/DniImage
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-ubi | netgear-dni
IMAGE/sysupgrade.tar := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | sysupgrade-tar kernel=$$$$@ | append-metadata
endef
-DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
+
+define Device/DniNorImage
+ PROFILES += $$(DEVICE_NAME)
+ FILESYSTEMS := squashfs
+ KERNEL_SUFFIX := -fit-uImage.itb
+ KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FIT_CFG_NAME)
+ KERNEL_NAME := Image
+ NETGEAR_BOARD_ID :=
+ NETGEAR_HW_ID :=
+ FIT_CFG_NAME :=
+ IMAGES := sysupgrade.bin factory.img
+ IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | append-rootfs | pad-rootfs | append-metadata
+ IMAGE/factory.img := $$(IMAGE/sysupgrade.bin) | netgear-dni
+endef
+DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID FIT_CFG_NAME
define Device/TpSafeImage
PROFILES += $$(DEVICE_NAME)
@@ -136,7 +150,7 @@ endef
TARGET_DEVICES += C2600
define Device/D7800
- $(call Device/DniImage)
+ $(call Device/DniNandImage)
DEVICE_DTS := qcom-ipq8064-d7800
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := D7800
@@ -193,7 +207,7 @@ endef
TARGET_DEVICES += FRITZ4040
define Device/R7500
- $(call Device/DniImage)
+ $(call Device/DniNandImage)
DEVICE_DTS := qcom-ipq8064-r7500
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7500
@@ -207,7 +221,7 @@ endef
TARGET_DEVICES += R7500
define Device/R7500v2
- $(call Device/DniImage)
+ $(call Device/DniNandImage)
DEVICE_DTS := qcom-ipq8064-r7500v2
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7500v2
@@ -221,7 +235,7 @@ endef
TARGET_DEVICES += R7500v2
define Device/R7800
- $(call Device/DniImage)
+ $(call Device/DniNandImage)
DEVICE_DTS := qcom-ipq8065-r7800
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7800
@@ -294,4 +308,19 @@ define Device/AP-DK04.1-C1
endef
TARGET_DEVICES += AP-DK04.1-C1
+define Device/EX61x0v2
+ $(call Device/DniNorImage)
+ DEVICE_DTS := qcom-ipq4019-ex61x0v2
+ FIT_CFG_NAME := config at ap.dk01.1-c1
+ KERNEL_LOADADDR := 0x80208000
+ NETGEAR_BOARD_ID := EX6150v2series
+ NETGEAR_HW_ID := 29765285+16+0+128+2x2
+ BLOCKSIZE := 64k
+ PAGESIZE := 256
+ SUPPORTED_DEVICES := ex6100v2 ex6150v2
+ DEVICE_PACKAGES := ath10k-firmware-qca4019 ipq-wifi-ex6100v2 ipq-wifi-ex6150v2
+ DEVICE_TITLE := Netgear EX6100v2/EX6150v2
+endef
+TARGET_DEVICES += EX61x0v2
+
$(eval $(call BuildImage))
diff --git a/target/linux/ipq806x/patches-4.9/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.9/0069-arm-boot-add-dts-files.patch
index bab2808789..c4915bdd6d 100644
--- a/target/linux/ipq806x/patches-4.9/0069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq806x/patches-4.9/0069-arm-boot-add-dts-files.patch
@@ -10,13 +10,14 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -618,7 +618,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -618,7 +618,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8084-mtp.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c1.dtb \
+ qcom-ipq4019-fritz4040.dtb \
+ qcom-ipq4019-nbg6617.dtb \
+ qcom-ipq4019-rt-ac58u.dtb \
++ qcom-ipq4019-ex61x0v2.dtb \
qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-c2600.dtb \
+ qcom-ipq8064-d7800.dtb \
--
2.15.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list