[OpenWrt-Devel] [PATCH v4 2/2] ath79: add support for devolo WiFi pro 1750c

David Bauer mail at david-bauer.net
Wed Dec 26 20:32:39 EST 2018


Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).

It is also not mentioned in the devolo manual.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail at david-bauer.net>
---
 .../ath79/base-files/etc/board.d/02_network   |  1 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata  |  3 +-
 .../ath79/dts/qca9558_devolo_dvl1750c.dts     | 46 +++++++++++++++++++
 .../ath79/dts/qca9558_devolo_dvl1xxx.dtsi     |  2 +-
 target/linux/ath79/image/generic.mk           |  8 ++++
 5 files changed, 58 insertions(+), 2 deletions(-)
 create mode 100644 target/linux/ath79/dts/qca9558_devolo_dvl1750c.dts

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 5d6a1eefcd..a258a6da61 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -10,6 +10,7 @@ ath79_setup_interfaces()
 
 	case "$board" in
 	avm,fritz300e|\
+	devolo,dvl1750c|\
 	ocedo,koala|\
 	ocedo,raccoon|\
 	pcs,cap324|\
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index e38e2a1933..885b57f6a1 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -87,7 +87,8 @@ board=$(board_name)
 case "$FIRMWARE" in
 "ath10k/cal-pci-0000:00:00.0.bin")
 	case $board in
-	devolo,dvl1200e)
+	devolo,dvl1200e|\
+	devolo,dvl1750c)
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
 		;;
diff --git a/target/linux/ath79/dts/qca9558_devolo_dvl1750c.dts b/target/linux/ath79/dts/qca9558_devolo_dvl1750c.dts
new file mode 100644
index 0000000000..b5a2954406
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_devolo_dvl1750c.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9558_devolo_dvl1xxx.dtsi"
+
+/ {
+	compatible = "devolo,dvl1750c", "qca,qca9557";
+	model = "devolo WiFi pro 1750c";
+
+	aliases {
+		led-boot = &status_blue;
+		led-failsafe = &status_red;
+		led-running = &status_blue;
+		led-upgrade = &status_red;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status_blue: status_blue {
+			label = "dvl1750c:blue:status";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		status_red: status_red {
+			label = "dvl1750c:red:status";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	beeper {
+		compatible = "gpio-beeper";
+		gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&gmac_config {
+	rxdv-delay = <3>;
+	rxd-delay = <3>;
+	txen-delay = <3>;
+	txd-delay = <3>;
+};
diff --git a/target/linux/ath79/dts/qca9558_devolo_dvl1xxx.dtsi b/target/linux/ath79/dts/qca9558_devolo_dvl1xxx.dtsi
index 185b29bdbe..9937186b1e 100644
--- a/target/linux/ath79/dts/qca9558_devolo_dvl1xxx.dtsi
+++ b/target/linux/ath79/dts/qca9558_devolo_dvl1xxx.dtsi
@@ -117,7 +117,7 @@
 	phy-handle = <&phy4>;
 	pll-data = <0xae000000 0x80000101 0x80001313>;
 
-	gmac-config {
+	gmac_config: gmac-config {
 		device = <&gmac>;
 
 		rxdv-delay = <3>;
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index ef8cf170de..b2f83ba58c 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -146,6 +146,14 @@ define Device/devolo_dvl1200e
 endef
 TARGET_DEVICES += devolo_dvl1200e
 
+define Device/devolo_dvl1750c
+  ATH_SOC := qca9558
+  DEVICE_TITLE := devolo WiFi pro 1750c
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  IMAGE_SIZE := 15936k
+endef
+TARGET_DEVICES += devolo_dvl1750c
+
 define Device/dlink_dir-825-b1
   ATH_SOC := ar7161
   DEVICE_TITLE := D-LINK DIR-825 B1
-- 
2.20.1


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list