[OpenWrt-Devel] ATH10K VLAN firmware issue

Bruno Antunes baantunes at gmail.com
Mon Nov 7 06:54:53 EST 2016


On 4 November 2016 at 22:23, Ben Greear <greearb at candelatech.com> wrote:
> The bug appears that vlan-tx-stripping is unconditionally enabled in
> at least my firmware.  I have re-compiled w/out that flag set, and it
> appears
> to work for me.
>
> Please download this firmware, rename it firmware-2.bin, make sure you
> remove/rename
> any firmware-5.bin (etc) so mine will load, and see if that fixes your
> problem.

Thanks for the fast reply but it only solves "half"  the problem.

Now the connection between the AP and the Sta can be secure and the
driver doesn't need to be loaded in rawmode.

Unfortunatly the the throughput is still bad.

iperf3 -c 10.10.4.15
Connecting to host 10.10.4.15, port 5201
[  4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.01   sec  42.4 KBytes   345 Kbits/sec    6   1.41 KBytes
[  4]   1.01-2.01   sec  0.00 Bytes  0.00 bits/sec    1   1.41 KBytes
[  4]   2.01-3.01   sec  0.00 Bytes  0.00 bits/sec    1   1.41 KBytes
[  4]   3.01-4.01   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes
[  4]   4.01-5.01   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes
[  4]   5.01-6.01   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes
[  4]   6.01-7.01   sec  0.00 Bytes  0.00 bits/sec    1   1.41 KBytes
[  4]   7.01-8.01   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes
[  4]   8.01-9.01   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes
[  4]   9.01-10.01  sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.01  sec  42.4 KBytes  34.7 Kbits/sec    9             sender
[  4]   0.00-10.01  sec  0.00 Bytes  0.00 bits/sec                  receiver

iperf Done.

>
> Please note that it is very likely you will have to use same MAC address
> for the VLAN devices that the underlying station uses in order for this to
> work.

Can you please elaborate more?
My setup  is the folowing.
The connection between the AP and Sta is in WDS
For the moment all devices are in the same VLAN.

client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2


Thanks,
Bruno

>
> https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
>
>
> Thanks,
> Ben
>
>
>

> Ben Greear <greearb at candelatech.com>
> Candela Technologies Inc  http://www.candelatech.com
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list