[OpenWrt-Devel] [PATCH 1/2] ipq806x: Add support for Netgear R7500v2
Alexis Green
agreen at cococorp.com
Wed Mar 23 15:55:09 EDT 2016
---
.../linux/ipq806x/base-files/etc/board.d/01_leds | 19 +-
.../ipq806x/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/firmware/11-ath10k-caldata | 50 +++
target/linux/ipq806x/base-files/lib/ipq806x.sh | 3 +
.../ipq806x/base-files/lib/upgrade/platform.sh | 6 +-
target/linux/ipq806x/image/Makefile | 14 +-
...-Netgear-Nighthawk-X4-D7500v2-device-tree.patch | 363 +++++++++++++++++++++
target/linux/ipq806x/profiles/netgear.mk | 13 +
8 files changed, 460 insertions(+), 11 deletions(-)
create mode 100755 target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
create mode 100644 target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index b32c1cc..2e86118 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -10,15 +10,20 @@ board_config_update
board=$(ipq806x_board_name)
+netgear_leds() {
+ ucidef_set_led_usbdev "usb1" "USB 1" "${board}:white:usb1" "1-1"
+ ucidef_set_led_usbdev "usb2" "USB 2" "${board}:white:usb3" "3-1"
+ ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0"
+ ucidef_set_led_ide "esata" "eSATA" "${board}:amber:esata"
+ ucidef_set_led_default "wps" "WPS" "${board}:white:wps" "0"
+ ucidef_set_led_default "rfkill" "rfkill" "${board}:white:rfkill" "0"
+}
+
case "$board" in
d7800 |\
-r7500)
- ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1"
- ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1"
- ucidef_set_led_netdev "wan" "WAN" "r7500:white:wan" "eth0"
- ucidef_set_led_ide "esata" "eSATA" "r7500:amber:esata"
- ucidef_set_led_default "wps" "WPS" "r7500:white:wps" "0"
- ucidef_set_led_default "rfkill" "rfkill" "r7500:white:rfkill" "0"
+r7500 |\
+r7500v2)
+ netgear_leds
;;
*)
;;
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 6e18297..0ee6b3e 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -14,7 +14,8 @@ board=$(ipq806x_board_name)
case "$board" in
ap148 |\
d7800 |\
-r7500)
+r7500 |\
+r7500v2)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6 at eth1" "5:wan" "0 at eth0"
;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
new file mode 100755
index 0000000..0f5b32c
--- /dev/null
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -0,0 +1,50 @@
+#!/bin/sh
+
+ath10kcal_die() {
+ echo "ath10cal: " "$*"
+ exit 1
+}
+
+ath10kcal_extract() {
+ local part=$1
+ local offset=$2
+ local count=$3
+ local mtd
+
+ mtd=$(find_mtd_chardev $part)
+ [ -n "$mtd" ] || \
+ ath10kcal_die "no mtd device found for partition $part"
+
+ dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+ ath10kcal_die "failed to extract calibration data from $mtd"
+}
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/ipq806x.sh
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(ipq806x_board_name)
+
+case "$FIRMWARE" in
+"ath10k/cal-pci-0000:01:00.0.bin")
+ case $board in
+ d7800 |\
+ r7500v2 )
+ ath10kcal_extract "art" 4096 12064
+ ;;
+ esac
+ ;;
+"ath10k/cal-pci-0001:01:00.0.bin")
+ case $board in
+ d7800 |\
+ r7500v2 )
+ ath10kcal_extract "art" 20480 12064
+ ;;
+ esac
+ ;;
+*)
+ exit 1
+ ;;
+esac
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index db22708..68cffd5 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -26,6 +26,9 @@ ipq806x_board_detect() {
*"R7500")
name="r7500"
;;
+ *"R7500v2")
+ name="r7500v2"
+ ;;
esac
[ -z "$name" ] && name="unknown"
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 542b5ce..1acdfe4 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -8,7 +8,8 @@ platform_check_image() {
case "$board" in
ap148 |\
d7800 |\
- r7500)
+ r7500 |\
+ r7500v2)
nand_do_platform_check $board $1
return $?;
;;
@@ -23,7 +24,8 @@ platform_pre_upgrade() {
case "$board" in
ap148 |\
d7800 |\
- r7500)
+ r7500 |\
+ r7500v2)
nand_do_upgrade "$1"
;;
esac
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index ff8b2c7..4040955 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -133,6 +133,18 @@ define Device/R7500
BOARD_NAME := r7500
endef
-TARGET_DEVICES += AP148 AP148-legacy D7800 DB149 R7500
+define Device/R7500v2
+ $(call Device/DniImage)
+ DEVICE_DTS := qcom-ipq8064-r7500v2
+ KERNEL_SIZE := 2097152
+ NETGEAR_BOARD_ID := R7500v2
+ NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
+ BLOCKSIZE := 128KiB
+ PAGESIZE := 2048
+ BOARD_NAME := r7500v2
+endef
+
+
+TARGET_DEVICES += AP148 AP148-legacy D7800 DB149 R7500 R7500v2
$(eval $(call BuildImage))
diff --git a/target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch b/target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch
new file mode 100644
index 0000000..5eff49a
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch
@@ -0,0 +1,363 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -362,6 +362,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+ qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-r7500.dtb \
++ qcom-ipq8064-r7500v2.dtb \
+ qcom-ipq8064-d7800.dtb \
+ qcom-msm8660-surf.dtb \
+ qcom-msm8960-cdp.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts
+@@ -0,0 +1,350 @@
++#include "qcom-ipq8064-v1.0.dtsi"
++
++#include <dt-bindings/input/input.h>
++
++/ {
++ model = "Netgear Nighthawk X4 R7500v2";
++ compatible = "netgear,r7500v2", "qcom,ipq8064";
++
++ memory at 0 {
++ reg = <0x42000000 0xe000000>;
++ device_type = "memory";
++ };
++
++ reserved-memory {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++ rsvd at 41200000 {
++ reg = <0x41200000 0x300000>;
++ no-map;
++ };
++ };
++
++ aliases {
++ serial0 = &uart4;
++ mdio-gpio0 = &mdio0;
++ };
++
++ chosen {
++ bootargs = "rootfstype=squashfs noinitrd";
++ linux,stdout-path = "serial0:115200n8";
++ };
++
++ soc {
++ pinmux at 800000 {
++ i2c4_pins: i2c4_pinmux {
++ pins = "gpio12", "gpio13";
++ function = "gsbi4";
++ bias-disable;
++ };
++
++ nand_pins: nand_pins {
++ mux {
++ pins = "gpio34", "gpio35", "gpio36",
++ "gpio37", "gpio38", "gpio39",
++ "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ function = "nand";
++ drive-strength = <10>;
++ bias-disable;
++ };
++ pullups {
++ pins = "gpio39";
++ bias-pull-up;
++ };
++ hold {
++ pins = "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ bias-bus-hold;
++ };
++ };
++
++ mdio0_pins: mdio0_pins {
++ mux {
++ pins = "gpio0", "gpio1";
++ function = "gpio";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++
++ rgmii2_pins: rgmii2_pins {
++ mux {
++ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++ function = "rgmii2";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++ };
++
++ gsbi at 16300000 {
++ qcom,mode = <GSBI_PROT_I2C_UART>;
++ status = "ok";
++ serial at 16340000 {
++ status = "ok";
++ };
++ /*
++ * The i2c device on gsbi4 should not be enabled.
++ * On ipq806x designs gsbi4 i2c is meant for exclusive
++ * RPM usage. Turning this on in kernel manifests as
++ * i2c failure for the RPM.
++ */
++ };
++
++ sata-phy at 1b400000 {
++ status = "ok";
++ };
++
++ sata at 29000000 {
++ status = "ok";
++ };
++
++ phy at 100f8800 { /* USB3 port 1 HS phy */
++ status = "ok";
++ };
++
++ phy at 100f8830 { /* USB3 port 1 SS phy */
++ status = "ok";
++ };
++
++ phy at 110f8800 { /* USB3 port 0 HS phy */
++ status = "ok";
++ };
++
++ phy at 110f8830 { /* USB3 port 0 SS phy */
++ status = "ok";
++ };
++
++ usb30 at 0 {
++ status = "ok";
++ };
++
++ usb30 at 1 {
++ status = "ok";
++ };
++
++ pcie0: pci at 1b500000 {
++ status = "ok";
++ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
++ pinctrl-0 = <&pcie0_pins>;
++ pinctrl-names = "default";
++ };
++
++ pcie1: pci at 1b700000 {
++ status = "ok";
++ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
++ pinctrl-0 = <&pcie1_pins>;
++ pinctrl-names = "default";
++ };
++
++ nand at 1ac00000 {
++ status = "ok";
++
++ pinctrl-0 = <&nand_pins>;
++ pinctrl-names = "default";
++
++ nand-ecc-strength = <4>;
++ nand-bus-width = <8>;
++
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ qcadata at 0 {
++ label = "qcadata";
++ reg = <0x0000000 0x0c80000>;
++ read-only;
++ };
++
++ APPSBL at c80000 {
++ label = "APPSBL";
++ reg = <0x0c80000 0x0500000>;
++ read-only;
++ };
++
++ APPSBLENV at 1180000 {
++ label = "APPSBLENV";
++ reg = <0x1180000 0x0080000>;
++ read-only;
++ };
++
++ art: art at 1200000 {
++ label = "art";
++ reg = <0x1200000 0x0140000>;
++ read-only;
++ };
++
++ artbak: art at 1340000 {
++ label = "artbak";
++ reg = <0x1340000 0x0140000>;
++ read-only;
++ };
++
++ kernel at 1480000 {
++ label = "kernel";
++ reg = <0x1480000 0x0200000>;
++ };
++
++ ubi at 1680000 {
++ label = "ubi";
++ reg = <0x1680000 0x1E00000>;
++ };
++
++ netgear at 3480000 {
++ label = "netgear";
++ reg = <0x3480000 0x4480000>;
++ read-only;
++ };
++
++ reserve at 7900000 {
++ label = "reserve";
++ reg = <0x7900000 0x0700000>;
++ read-only;
++ };
++
++ firmware at 1480000 {
++ label = "firmware";
++ reg = <0x1480000 0x2000000>;
++ };
++
++ };
++
++ mdio0: mdio {
++ compatible = "virtual,mdio-gpio";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++ pinctrl-0 = <&mdio0_pins>;
++ pinctrl-names = "default";
++
++ phy0: ethernet-phy at 0 {
++ device_type = "ethernet-phy";
++ reg = <0>;
++ qca,ar8327-initvals = <
++ 0x00004 0x7600000 /* PAD0_MODE */
++ 0x00008 0x1000000 /* PAD5_MODE */
++ 0x0000c 0x80 /* PAD6_MODE */
++ 0x000e4 0xaa545 /* MAC_POWER_SEL */
++ 0x000e0 0xc74164de /* SGMII_CTRL */
++ 0x0007c 0x4e /* PORT0_STATUS */
++ 0x00094 0x4e /* PORT6_STATUS */
++ >;
++ };
++
++ phy4: ethernet-phy at 4 {
++ device_type = "ethernet-phy";
++ reg = <4>;
++ };
++ };
++
++ gmac1: ethernet at 37200000 {
++ status = "ok";
++ phy-mode = "rgmii";
++ qcom,id = <1>;
++
++ pinctrl-0 = <&rgmii2_pins>;
++ pinctrl-names = "default";
++
++ mtd-mac-address = <&art 6>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++
++ gmac2: ethernet at 37400000 {
++ status = "ok";
++ phy-mode = "sgmii";
++ qcom,id = <2>;
++
++ mtd-mac-address = <&art 0>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ wifi {
++ label = "wifi";
++ gpios = <&qcom_pinmux 6 1>;
++ linux,code = <KEY_WLAN>;
++ };
++
++ reset {
++ label = "reset";
++ gpios = <&qcom_pinmux 54 1>;
++ linux,code = <KEY_RESTART>;
++ };
++
++ wps {
++ label = "wps";
++ gpios = <&qcom_pinmux 65 1>;
++ linux,code = <KEY_WPS_BUTTON>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ usb1 {
++ label = "r7500v2:amber:usb1";
++ gpios = <&qcom_pinmux 7 0>;
++ };
++
++ usb3 {
++ label = "r7500v2:amber:usb3";
++ gpios = <&qcom_pinmux 8 0>;
++ };
++
++ status {
++ label = "r7500v2:amber:status";
++ gpios = <&qcom_pinmux 9 0>;
++ };
++
++ internet {
++ label = "r7500v2:white:internet";
++ gpios = <&qcom_pinmux 22 0>;
++ };
++
++ wan {
++ label = "r7500v2:white:wan";
++ gpios = <&qcom_pinmux 23 0>;
++ };
++
++ wps {
++ label = "r7500v2:white:wps";
++ gpios = <&qcom_pinmux 24 0>;
++ };
++
++ esata {
++ label = "r7500v2:white:esata";
++ gpios = <&qcom_pinmux 26 0>;
++ };
++
++ power {
++ label = "r7500v2:white:power";
++ gpios = <&qcom_pinmux 53 0>;
++ default-state = "on";
++ };
++
++ rfkill {
++ label = "r7500v2:white:rfkill";
++ gpios = <&qcom_pinmux 64 0>;
++ };
++
++ };
++};
++
++&adm_dma {
++ status = "ok";
++};
diff --git a/target/linux/ipq806x/profiles/netgear.mk b/target/linux/ipq806x/profiles/netgear.mk
index 25258cd..e64831b 100644
--- a/target/linux/ipq806x/profiles/netgear.mk
+++ b/target/linux/ipq806x/profiles/netgear.mk
@@ -29,5 +29,18 @@ endef
define Profile/R7500/Description
Package set for the Netgear Nighthawk X4 R7500.
endef
+
+define Profile/R7500v2
+ NAME:=Netgear Nighthawk X4 R7500v2
+ PACKAGES:= \
+ kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \
+ kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \
+ kmod-ath10k wpad-mini ath10k-firmware-qca99x0
+endef
+
+define Profile/R7500v2/Description
+ Package set for the Netgear Nighthawk X4 R7500v2.
+endef
$(eval $(call Profile,D7800))
$(eval $(call Profile,R7500))
+$(eval $(call Profile,R7500v2))
--
2.1.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list