[OpenWrt-Devel] [PATCH] ramips: add support for Planex MZK-EX750NP.
＠SRCHACK.ORG
tochiro.srchack at gmail.com
Thu Apr 28 06:47:50 EDT 2016
Hi, Dear Piotr.
Status quo, is the only way there is access in the UART.
Looking for a good way. I'm thinking.
On 2016/04/28 19:24, Piotr Dymacz wrote:
> Hello YuheiOKAWA,
>
> Just small question.
> How the user can access the device if it doesn't have Ethernet and the
> WiFi is disabled by default in OpenWrt?
>
> Cheers,
> Piotr
>
>
> 2016-04-28 11:49 GMT+02:00 YuheiOKAWA <tochiro.srchack at gmail.com>:
>> add support for Planex MZK-EX750NP.
>> MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
>> Built-in power supply.
>> 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
>>
>> Signed-off-by: YuheiOKAWA <tochiro.srchack at gmail.com>
>> ---
>> target/linux/ramips/base-files/etc/board.d/01_leds | 4 +
>> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
>> target/linux/ramips/base-files/etc/diag.sh | 3 +-
>> target/linux/ramips/base-files/lib/ramips.sh | 3 +
>> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
>> target/linux/ramips/dts/MZK-EX750NP.dts | 150 +++++++++++++++++++++
>> target/linux/ramips/image/mt7620.mk | 2 +
>> target/linux/ramips/mt7620/profiles/planex.mk | 11 ++
>> 8 files changed, 174 insertions(+), 1 deletion(-)
>> create mode 100644 target/linux/ramips/dts/MZK-EX750NP.dts
>>
>> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
>> index aeaab33..47e1e6a 100755
>> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
>> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
>> @@ -206,6 +206,10 @@ mr-102n)
>> set_wifi_led "$board:green:wlan"
>> set_usb_led "$board:green:usb"
>> ;;
>> +mzk-ex750np)
>> + ucidef_set_led_default "power" "power" "$board:red:power" "1"
>> + set_wifi_led "$board:red:wifi"
>> + ;;
>> na930)
>> set_usb_led "$board:blue:status"
>> ;;
>> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
>> index c6c740f..ee690f6 100755
>> --- a/target/linux/ramips/base-files/etc/board.d/02_network
>> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
>> @@ -165,6 +165,7 @@ ramips_setup_interfaces()
>> d105|\
>> hpm|\
>> mzk-ex300np|\
>> + mzk-ex750np|\
>> na930|\
>> wli-tx4-ag300n|\
>> wrh-300cr)
>> diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
>> index 20ff8ff..c638d16 100644
>> --- a/target/linux/ramips/base-files/etc/diag.sh
>> +++ b/target/linux/ramips/base-files/etc/diag.sh
>> @@ -41,7 +41,8 @@ get_status_led() {
>> hlk-rm04|\
>> jhr-n825r|\
>> mpr-a1|\
>> - mpr-a2)
>> + mpr-a2|\
>> + mzk-ex750np)
>> status_led="$board:red:power"
>> ;;
>> ai-br100|\
>> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
>> index 2c669c5..0ac0f68 100755
>> --- a/target/linux/ramips/base-files/lib/ramips.sh
>> +++ b/target/linux/ramips/base-files/lib/ramips.sh
>> @@ -298,6 +298,9 @@ ramips_board_detect() {
>> *"MZK-EX300NP")
>> name="mzk-ex300np"
>> ;;
>> + *"MZK-EX750NP")
>> + name="mzk-ex750np"
>> + ;;
>> *"MZK-W300NH2"*)
>> name="mzk-w300nh2"
>> ;;
>> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> index 2b24030..86ea4a3 100755
>> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
>> @@ -90,6 +90,7 @@ platform_check_image() {
>> mzk-750dhp|\
>> mzk-dp150n|\
>> mzk-ex300np|\
>> + mzk-ex750np|\
>> mzk-w300nh2|\
>> mzk-wdpr|\
>> nbg-419n|\
>> diff --git a/target/linux/ramips/dts/MZK-EX750NP.dts b/target/linux/ramips/dts/MZK-EX750NP.dts
>> new file mode 100644
>> index 0000000..9b5b418
>> --- /dev/null
>> +++ b/target/linux/ramips/dts/MZK-EX750NP.dts
>> @@ -0,0 +1,150 @@
>> +/dts-v1/;
>> +
>> +/include/ "mt7620a.dtsi"
>> +
>> +/ {
>> + compatible = "ralink,mt7620a-soc";
>> + model = "Planex MZK-EX750NP";
>> +
>> + palmbus at 10000000 {
>> + gpio2: gpio at 660 {
>> + status = "okay";
>> + };
>> +
>> + gpio3: gpio at 688 {
>> + status = "okay";
>> + };
>> +
>> + spi at b00 {
>> + status = "okay";
>> +
>> + m25p80 at 0 {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "jedec,spi-nor";
>> + reg = <0 0>;
>> + linux,modalias = "m25p80", "w25q64";
>> + spi-max-frequency = <10000000>;
>> +
>> + partition at 0 {
>> + label = "u-boot";
>> + reg = <0x0 0x30000>;
>> + read-only;
>> + };
>> +
>> + partition at 30000 {
>> + label = "u-boot-env";
>> + reg = <0x30000 0x10000>;
>> + read-only;
>> + };
>> +
>> + factory: partition at 40000 {
>> + label = "factory";
>> + reg = <0x40000 0x10000>;
>> + read-only;
>> + };
>> +
>> + partition at 50000 {
>> + label = "firmware";
>> + reg = <0x50000 0x730000>;
>> + };
>> +
>> + partition at 780000 {
>> + label = "Udata";
>> + reg = <0x780000 0x80000>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + pinctrl {
>> + state_default: pinctrl0 {
>> + gpio {
>> + ralink,group = "uartf", "nd_sd", "rgmii2", "wled";
>> + ralink,function = "gpio";
>> + };
>> + };
>> + };
>> +
>> + ethernet at 10100000 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&ephy_pins>;
>> + mtd-mac-address = <&factory 0x4>;
>> + mediatek,portmap = "llllw";
>> + };
>> +
>> + wmac at 10180000 {
>> + ralink,mtd-eeprom = <&factory 0>;
>> + };
>> +
>> + pcie at 10140000 {
>> + status = "okay";
>> +
>> + pcie-bridge {
>> + mt76 at 0,0 {
>> + reg = <0x0000 0 0 0 0>;
>> + device_type = "pci";
>> + mediatek,mtd-eeprom = <&factory 0x8000>;
>> + mediatek,2ghz = <0>;
>> + };
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> +
>> + power {
>> + label = "mzk-ex750np:red:power";
>> + gpios = <&gpio0 14 1>;
>> + };
>> +
>> + wifi {
>> + label = "mzk-ex750np:red:wifi";
>> + gpios = <&gpio3 0 1>;
>> + };
>> +
>> + wps {
>> + label = "mzk-ex750np:green:wps";
>> + gpios = <&gpio0 10 1>;
>> + };
>> +
>> + rep {
>> + label = "mzk-ex750np:blue:rep";
>> + gpios = <&gpio2 16 1>;
>> + };
>> +
>> + wifi1 {
>> + label = "mzk-ex750np:blue:wifi1";
>> + gpios = <&gpio2 19 1>;
>> + };
>> +
>> + wifi2 {
>> + label = "mzk-ex750np:blue:wifi2";
>> + gpios = <&gpio2 18 1>;
>> + };
>> +
>> + wifi3 {
>> + label = "mzk-ex750np:blue:wifi3";
>> + gpios = <&gpio2 17 1>;
>> + };
>> + };
>> +
>> + gpio-keys-polled {
>> + compatible = "gpio-keys-polled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + poll-interval = <20>;
>> +
>> + reset {
>> + label = "reset";
>> + gpios = <&gpio0 9 1>;
>> + linux,code = <0x198>;
>> + };
>> +
>> + wps {
>> + label = "wps";
>> + gpios = <&gpio0 13 0>;
>> + linux,code = <0x211>;
>> + };
>> + };
>> +};
>> diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
>> index 35cb46a..09c0ec2 100644
>> --- a/target/linux/ramips/image/mt7620.mk
>> +++ b/target/linux/ramips/image/mt7620.mk
>> @@ -102,6 +102,7 @@ Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930
>> Image/Build/Profile/DB-WRT01=$(call BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
>> Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
>> Image/Build/Profile/MZK-EX300NP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-ex300np,MZK-EX300NP)
>> +Image/Build/Profile/MZK-EX750NP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-ex750np,MZK-EX750NP)
>> Image/Build/Profile/HC5661=$(call BuildFirmware/Default16M/$(1),$(1),hc5661,HC5661)
>> Image/Build/Profile/HC5761=$(call BuildFirmware/Default16M/$(1),$(1),hc5761,HC5761)
>> Image/Build/Profile/HC5861=$(call BuildFirmware/Default16M/$(1),$(1),hc5861,HC5861)
>> @@ -149,6 +150,7 @@ define Image/Build/Profile/Default
>> $(call Image/Build/Profile/DB-WRT01,$(1))
>> $(call Image/Build/Profile/MZK-750DHP,$(1))
>> $(call Image/Build/Profile/MZK-EX300NP,$(1))
>> + $(call Image/Build/Profile/MZK-EX750NP,$(1))
>> $(call Image/Build/Profile/NA930,$(1))
>> $(call Image/Build/Profile/HC5661,$(1))
>> $(call Image/Build/Profile/HC5761,$(1))
>> diff --git a/target/linux/ramips/mt7620/profiles/planex.mk b/target/linux/ramips/mt7620/profiles/planex.mk
>> index 157cf8d..f461aeb 100644
>> --- a/target/linux/ramips/mt7620/profiles/planex.mk
>> +++ b/target/linux/ramips/mt7620/profiles/planex.mk
>> @@ -39,3 +39,14 @@ define Profile/MZK-EX300NP/Description
>> Package set optimized for the Planex MZK-EX300NP.
>> endef
>> $(eval $(call Profile,MZK-EX300NP))
>> +
>> +
>> +define Profile/MZK-EX750NP
>> + NAME:=Planex MZK-EX750NP
>> + PACKAGES:= kmod-mt76 kmod-mt7610e
>> +endef
>> +
>> +define Profile/MZK-EX750NP/Description
>> + Package set optimized for the Planex MZK-EX750NP.
>> +endef
>> +$(eval $(call Profile,MZK-EX750NP))
>> --
>> 1.9.1
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel at lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
--
------------------------------------------------------
＠SRCHACK.ORG
tochiro.srchack at gmail.com
http://www.srchack.org/
------------------------------------------------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list