[OpenWrt-Devel] [PATCH] CC: ramips: Added WIZnet WizFi630A Platfrom based on Ralink RT5350
Tobias Welz
tw at wiznet.eu
Wed Sep 30 06:58:12 EDT 2015
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
This is a backport of patch r46921
Signed-off-by: Tobias Welz <tw at wiznet.eu>
---
.../linux/ramips/base-files/etc/board.d/02_network | 11 +-
target/linux/ramips/base-files/etc/diag.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/WIZFI630A.dts | 180 ++++++++++++++++++++
target/linux/ramips/image/Makefile | 3 +
target/linux/ramips/rt305x/profiles/wiznet.mk | 17 ++
6 files changed, 214 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/WIZFI630A.dts
create mode 100644 target/linux/ramips/rt305x/profiles/wiznet.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index bc1fc0191cec..6affe9feb26e 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -156,7 +156,12 @@ ramips_setup_interfaces()
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
ucidef_add_switch_vlan "switch0" "2" "5 6t"
;;
-
+ wizfi630a)
+ ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+ ucidef_add_switch "switch0" "1" "1"
+ ucidef_add_switch_vlan "switch0" "1" "1 2 6t"
+ ucidef_add_switch_vlan "switch0" "2" "0 6t"
+ ;;
awm002-evb | \
awm003-evb | \
argus-atp52b | \
@@ -363,6 +368,10 @@ ramips_setup_macs()
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$wan_mac
;;
+ wizfi630a)
+ lan_mac=$(mtd_get_mac_binary factory 4)
+ wan_mac=$(mtd_get_mac_binary factory 40)
+ ;;
wsr-1166)
local index="$(find_mtd_index "board_data")"
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index e695778a6aa2..5fc5137ce2b4 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -175,6 +175,9 @@ get_status_led() {
whr-g300n)
status_led="whr-g300n:green:router"
;;
+ wizfi630a)
+ status_led="wizfi630a::run"
+ ;;
wmr300)
status_led="buffalo:green:status"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index cedd62bccd47..39d74d75a34d 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -103,6 +103,7 @@ platform_check_image() {
whr-300hp2 |\
whr-600d |\
whr-1166d |\
+ wizfi630a |\
wsr-600 |\
wl-330n | \
wl-330n3g | \
diff --git a/target/linux/ramips/dts/WIZFI630A.dts b/target/linux/ramips/dts/WIZFI630A.dts
new file mode 100644
index 000000000000..f2818ce9df8a
--- /dev/null
+++ b/target/linux/ramips/dts/WIZFI630A.dts
@@ -0,0 +1,180 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+ compatible = "wizfi630a", "ralink,rt5350-soc";
+ model = "WIZnet WizFi630A";
+
+ chosen {
+ bootargs = "console=ttyS1,115200";
+ };
+
+ palmbus at 10000000 {
+ gpio1: gpio at 660 {
+ status = "okay";
+ };
+
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q128";
+ reg = <0>;
+ linux,modalias = "m25p80", "w25q128";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "uboot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+ };
+ };
+
+ uart at 500 {
+ compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
+ reg = <0x500 0x100>;
+ resets = <&rstctrl 12>;
+ reset-names = "uart";
+ interrupt-parent = <&intc>;
+ interrupts = <5>;
+ reg-shift = <2>;
+ status = "okay";
+ };
+
+ uartlite at c00 {
+ compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
+ reg = <0xc00 0x100>;
+ resets = <&rstctrl 19>;
+ reset-names = "uartl";
+ interrupt-parent = <&intc>;
+ interrupts = <12>;
+ reg-shift = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uartlite_pins>;
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "i2c", "jtag" ;
+ ralink,function = "gpio";
+ };
+ };
+
+ uartf_gpio_pins: uartf_gpio {
+ uartf_gpio {
+ ralink,group = "uartf";
+ ralink,function = "uartf";
+ };
+ };
+
+ uartlite_pins: uartlite {
+ uart {
+ ralink,group = "uartlite";
+ ralink,function = "uartlite";
+ };
+ };
+ };
+
+ ethernet at 10100000 {
+ mtd-mac-address = <&factory 0x4>;
+ };
+
+ esw at 10110000 {
+ ralink,portmap = <0x17>;
+ };
+
+ wmac at 10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ ehci at 101c0000 {
+ status = "okay";
+ };
+
+ ohci at 101c1000 {
+ status = "okay";
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ run {
+ label = "wizfi630a::run";
+ gpios = <&gpio0 1 1>;
+ };
+
+ wps {
+ label = "wizfi630a::wps";
+ gpios = <&gpio0 20 1>;
+ };
+
+ uart1 {
+ label = "wizfi630a::uart1";
+ gpios = <&gpio0 18 1>;
+ };
+
+ uart2 {
+ label = "wizfi630a::uart2";
+ gpios = <&gpio0 21 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 17 1>;
+ linux,code = <0x198>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 0 1>;
+ linux,code = <0x211>;
+ };
+
+ scm1 {
+ label = "SCM1";
+ gpios = <&gpio0 19 1>;
+ linux,code = <0x100>;
+ };
+
+ scm2 {
+ label = "SCM2";
+ gpios = <&gpio0 2 1>;
+ linux,code = <0x101>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 776920ba6b98..3bfbcd0b6d93 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -627,6 +627,8 @@ endef
BuildFirmware/WHRG300N/initramfs=$(call BuildFirmware/OF/initramfs,$(1),whr-g300n,WHR-G300N)
Image/Build/Profile/WHRG300N=$(call BuildFirmware/WHRG300N/$(1),$(1))
+Image/Build/Profile/WIZFI630A=$(call BuildFirmware/Default16M/$(1),$(1),wizfi630a,WIZFI630A)
+
Image/Build/Profile/WIZARD8800=$(call BuildFirmware/Default8M/$(1),$(1),wizard-8800,WIZARD8800,Linux Kernel Image)
Image/Build/Profile/WL_330N=$(call BuildFirmware/Default4M/$(1),$(1),wl-330n,WL_330N)
@@ -761,6 +763,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/WCR150GN,$(1))
$(call Image/Build/Profile/WHRG300N,$(1))
$(call Image/Build/Profile/WIZARD8800,$(1))
+ $(call Image/Build/Profile/WIZFI630A,$(1))
$(call Image/Build/Profile/WL_330N,$(1))
$(call Image/Build/Profile/WL_330N3G,$(1))
$(call Image/Build/Profile/WL341V3,$(1))
diff --git a/target/linux/ramips/rt305x/profiles/wiznet.mk b/target/linux/ramips/rt305x/profiles/wiznet.mk
new file mode 100644
index 000000000000..83f2af0cd938
--- /dev/null
+++ b/target/linux/ramips/rt305x/profiles/wiznet.mk
@@ -0,0 +1,17 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/WIZFI630A
+ NAME:=WIZnet WizFi630A
+ PACKAGES:=\
+ kmod-usb2
+endef
+
+define Profile/WIZFI630A/Description
+ Package set for WIZnet WizFi630A board
+endef
+$(eval $(call Profile,WIZFI630A))
--
1.7.10.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list