[OpenWrt-Devel] [PATCH 2/2] ar71xx: Add support for AirTight Networks C-55
Chris Blake
chrisrblake93 at gmail.com
Mon Sep 21 09:20:34 EDT 2015
This patch is to add support for the AirTight Networks C-55 Access Point
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
---
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh
b/target/linux/ar71xx/base-files/etc/diag.sh
index cfba6b4..5773186 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -53,6 +53,9 @@ get_status_led() {
bxu2000n-2-a1)
status_led="bhu:green:status"
;;
+ c-55)
+ status_led="c-55:green:pwr"
+ ;;
cap4200ag)
status_led="senao:green:pwr"
;;
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index b5f0588..af94cae 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -38,6 +38,10 @@ board=$(ar71xx_board_name)
case "$FIRMWARE" in
"soc_wmac.eeprom")
case $board in
+ c-55)
+ ath9k_eeprom_extract "art" 4096 2048
+ ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1)
+ ;;
r6100 | \
wndr3700v4 | \
wndr4300)
@@ -52,6 +56,10 @@ case "$FIRMWARE" in
"pci_wmac0.eeprom")
case $board in
+ c-55)
+ ath9k_eeprom_extract "art" 20480 2048
+ ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +2)
+ ;;
wndr3700v4 | \
wndr4300)
ath9k_eeprom_extract "caldata" 20480 2048
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
index fac4751..d9e45bd 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
@@ -85,6 +85,12 @@ bxu2000n-2-a1)
ucidef_set_led_wlan "wlan" "WLAN" "bhu:green:wlan" "phy0tpt"
;;
+c-55)
+ ucidef_set_led_netdev "lan_green" "LAN_GREEN" "c-55:green:lan" "eth0"
+ ucidef_set_led_wlan "wlan_amber" "WLAN_AMBER" "c-55:amber:wlan" "phy0tpt"
+ ucidef_set_led_wlan "wlan_green" "WLAN_GREEN" "c-55:green:wlan" "phy1tpt"
+ ;;
+
cap4200ag)
ucidef_set_led_default "lan_green" "LAN_GREEN" "senao:green:lan" "1"
ucidef_set_led_wlan "wlan_amber" "WLAN_AMBER" "senao:amber:wlan" "phy0tpt"
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
index 880953c..d0e1847 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
@@ -341,6 +341,7 @@ dlan-pro-1200-ac)
all0305 |\
aw-nr580 |\
bullet-m |\
+c-55 |\
cap4200ag |\
eap300v2 |\
eap7660d |\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh
b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index efb3d16..1174995 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -398,6 +398,9 @@ ar71xx_board_detect() {
*AW-NR580)
name="aw-nr580"
;;
+ *C-55)
+ name="c-55"
+ ;;
*CAP4200AG)
name="cap4200ag"
;;
diff --git a/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
b/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
index 92b3765..1d501a8 100644
--- a/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
+++ b/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
@@ -22,6 +22,10 @@ fetch_mac_from_mtd() {
preinit_set_mac_address() {
case $(ar71xx_board_name) in
+ c-55)
+ mac_lan=$(mtd_get_mac_binary art 0)
+ [ -n "$mac_lan" ] && ifconfig eth0 hw ether "$mac_lan"
+ ;;
dir-615-c1)
fetch_mac_from_mtd config lan_mac wan_mac
echo 1 > /sys/class/leds/dir-615-c1:green:wancpu/brightness
@@ -45,4 +49,3 @@ preinit_set_mac_address() {
}
boot_hook_add preinit_main preinit_set_mac_address
-
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index cad8b43..e6e3820 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -199,6 +199,7 @@ platform_check_image() {
ap81 | \
ap83 | \
ap132 | \
+ c-55 | \
cf-e316n-v2 | \
dgl-5500-a1 |\
dhp-1565-a1 |\
diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1
index 51f2f2f..f28a07a 100644
--- a/target/linux/ar71xx/config-4.1
+++ b/target/linux/ar71xx/config-4.1
@@ -49,6 +49,7 @@ CONFIG_ATH79_MACH_ARCHER_C7=y
CONFIG_ATH79_MACH_AW_NR580=y
CONFIG_ATH79_MACH_BHU_BXU2000N2_A=y
CONFIG_ATH79_MACH_BSB=y
+CONFIG_ATH79_MACH_C55=y
CONFIG_ATH79_MACH_CAP4200AG=y
CONFIG_ATH79_MACH_CARAMBOLA2=y
CONFIG_ATH79_MACH_CF_E316N_V2=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-c55.c
b/target/linux/ar71xx/files/arch/mips/ath79/mach-c55.c
new file mode 100644
index 0000000..cbee18e
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-c55.c
@@ -0,0 +1,132 @@
+/*
+ * AirTight Networks C-55 board support
+ *
+ * Copyright (C) 2014-2015 Chris Blake <chrisrblake93 at gmail.com>
+ *
+ * Based on Senao CAP4200AG board support
+ *
+ * Copyright (C) 2012 Gabor Juhos <juhosg at openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/phy.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "pci.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-spi.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define C55_GPIO_LED_PWR_GREEN 12
+#define C55_GPIO_LED_PWR_AMBER 13
+#define C55_GPIO_LED_LAN_GREEN 14
+#define C55_GPIO_LED_LAN_AMBER 15
+#define C55_GPIO_LED_WLAN_GREEN 18
+#define C55_GPIO_LED_WLAN_AMBER 19
+
+#define C55_GPIO_BTN_RESET 17
+
+#define C55_KEYS_POLL_INTERVAL 20 /* msecs */
+#define C55_KEYS_DEBOUNCE_INTERVAL (3 * C55_KEYS_POLL_INTERVAL)
+
+#define C55_MAC_OFFSET 0
+#define C55_WMAC_CALDATA_OFFSET 0x1000
+#define C55_PCIE_CALDATA_OFFSET 0x5000
+
+static struct gpio_led c55_leds_gpio[] __initdata = {
+ {
+ .name = "c-55:green:pwr",
+ .gpio = C55_GPIO_LED_PWR_GREEN,
+ .active_low = 1,
+ },
+ {
+ .name = "c-55:amber:pwr",
+ .gpio = C55_GPIO_LED_PWR_AMBER,
+ .active_low = 1,
+ },
+ {
+ .name = "c-55:green:lan",
+ .gpio = C55_GPIO_LED_LAN_GREEN,
+ .active_low = 1,
+ },
+ {
+ .name = "c-55:amber:lan",
+ .gpio = C55_GPIO_LED_LAN_AMBER,
+ .active_low = 1,
+ },
+ {
+ .name = "c-55:green:wlan",
+ .gpio = C55_GPIO_LED_WLAN_GREEN,
+ .active_low = 1,
+ },
+ {
+ .name = "c-55:amber:wlan",
+ .gpio = C55_GPIO_LED_WLAN_AMBER,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button c55_gpio_keys[] __initdata = {
+ {
+ .desc = "Reset button",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = C55_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = C55_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static void __init c55_setup(void)
+{
+ /* SPI Storage*/
+ ath79_register_m25p80_large(NULL);
+
+ /* MDIO Interface */
+ ath79_register_mdio(0, 0x0);
+
+ /* AR8035-A Ethernet */
+ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0 |
+ AR934X_ETH_CFG_SW_ONLY_MODE);
+ ath79_init_mac(ath79_eth0_data.mac_addr, NULL, 0);
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ath79_eth0_data.phy_mask = BIT(0);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth0_pll_data.pll_1000 = 0x06000000;
+ ath79_register_eth(0);
+
+ /* LEDs & GPIO */
+ ath79_gpio_output_select(C55_GPIO_LED_LAN_GREEN,
+ AR934X_GPIO_OUT_GPIO);
+ ath79_gpio_output_select(C55_GPIO_LED_LAN_AMBER,
+ AR934X_GPIO_OUT_GPIO);
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(c55_leds_gpio),
+ c55_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, C55_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(c55_gpio_keys),
+ c55_gpio_keys);
+
+ /* WiFi */
+ ath79_wmac_disable_2ghz();
+ ath79_register_wmac_simple();
+ ap91_pci_init_simple();
+
+}
+MIPS_MACHINE(ATH79_MACH_C55, "C-55", "AirTight Networks C-55",
+ c55_setup);
diff --git a/target/linux/ar71xx/generic/profiles/airtight.mk
b/target/linux/ar71xx/generic/profiles/airtight.mk
new file mode 100644
index 0000000..00f9ce4
--- /dev/null
+++ b/target/linux/ar71xx/generic/profiles/airtight.mk
@@ -0,0 +1,17 @@
+#
+# Copyright (C) 2015 Chris Blake (chrisrblake93 at gmail.com)
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/C-55
+ NAME:=AirTight Networks C-55
+ PACKAGES:=kmod-ath9k
+endef
+
+define Profile/C-55/Description
+ Package set optimized for the AirTight Networks C-55 AP.
+endef
+
+$(eval $(call Profile,C-55))
diff --git a/target/linux/ar71xx/image/Makefile
b/target/linux/ar71xx/image/Makefile
index b00846f..57a9881 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -1244,6 +1244,7 @@
ap143_mtdlayout_16M=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(root
ap147_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(rootfs),1472k(kernel),64k(art),16000k at 0x50000(firmware)
ap152_mtdlayout_16M=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(rootfs),1472k(kernel),64k(art)ro,16000k at 0x50000(firmware)
bxu2000n2_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),8448k(rootfs),6016k(user),64k(cfg),64k(oem),64k(art)ro
+c55_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,128k(u-boot-env)ro,2048k(kernel),13824k(rootfs),13824k(opt)ro,2624k(failsafe)ro,64k(art)ro,15872k at 0x60000(firmware)
cameo_ap81_mtdlayout=mtdparts=spi0.0:128k(u-boot)ro,64k(config)ro,3840k(firmware),64k(art)ro
cameo_ap91_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(nvram)ro,3712k(firmware),64k(mac)ro,64k(art)ro
cameo_ap99_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(nvram)ro,3520k(firmware),64k(mac)ro,192k(lp)ro,64k(art)ro
@@ -2130,6 +2131,7 @@ $(eval $(call
SingleProfile,AthLzma,64k,AP143_8M,ap143-8M,AP143,ttyS0,115200,$$(
$(eval $(call SingleProfile,AthLzma,64k,AP143_16M,ap143-16M,AP143,ttyS0,115200,$$(ap143_mtdlayout_16M),RKuImage))
$(eval $(call SingleProfile,AthLzma,64k,AP147_010,ap147-010,AP147-010,ttyS0,115200,$$(ap147_mtdlayout),RKuImage))
$(eval $(call SingleProfile,AthLzma,64k,AP152_16M,ap152-16M,AP152,ttyS0,115200,$$(ap152_mtdlayout_16M),RKuImage))
+$(eval $(call SingleProfile,AthLzma,64k,C-55,c-55,C-55,ttyS0,115200,$$(c55_mtdlayout),KRuImage))
$(eval $(call SingleProfile,AthLzma,64k,BXU2000N2,bxu2000n-2-a1,BXU2000n-2-A1,ttyS0,115200,$$(bxu2000n2_mtdlayout),RKuImage))
$(eval $(call SingleProfile,AthLzma,64k,CAP4200AG,cap4200ag,CAP4200AG,ttyS0,115200,$$(cap4200ag_mtdlayout),KRuImage))
$(eval $(call SingleProfile,AthLzma,64k,DB120,db120,DB120,ttyS0,115200,$$(db120_mtdlayout),RKuImage))
diff --git a/target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-at-c55-support.patch
b/target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-at-c55-support.patch
new file mode 100644
index 0000000..6addcdc
--- /dev/null
+++ b/target/linux/ar71xx/patches-4.1/817-MIPS-ath79-add-at-c55-support.patch
@@ -0,0 +1,39 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -239,6 +239,16 @@ config ATH79_MACH_PB92
+ select ATH79_DEV_PB9X_PCI if PCI
+ select ATH79_DEV_USB
+
++config ATH79_MACH_C55
++ bool "AirTight Networks C-55 support"
++ select SOC_AR934X
++ select ATH79_DEV_AP9X_PCI if PCI
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
++ select ATH79_DEV_WMAC
++
+ config ATH79_MACH_AW_NR580
+ bool "AzureWave AW-NR580 board support"
+ select SOC_AR71XX
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -36,6 +36,7 @@ enum ath79_mach_type {
+ ATH79_MACH_AP81, /* Atheros AP81 reference board */
+ ATH79_MACH_AP83, /* Atheros AP83 */
+ ATH79_MACH_AP96, /* Atheros AP96 */
++ ATH79_MACH_C55, /* AirTight Networks C-55 */
+ ATH79_MACH_ARCHER_C5, /* TP-LINK Archer C5 board */
+ ATH79_MACH_ARCHER_C7, /* TP-LINK Archer C7 board */
+ ATH79_MACH_AW_NR580, /* AzureWave AW-NR580 */
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -54,6 +54,7 @@ obj-$(CONFIG_ATH79_MACH_AP152) += mach-
+ obj-$(CONFIG_ATH79_MACH_AP81) += mach-ap81.o
+ obj-$(CONFIG_ATH79_MACH_AP83) += mach-ap83.o
+ obj-$(CONFIG_ATH79_MACH_AP96) += mach-ap96.o
++obj-$(CONFIG_ATH79_MACH_C55) += mach-c55.o
+ obj-$(CONFIG_ATH79_MACH_ARCHER_C7) += mach-archer-c7.o
+ obj-$(CONFIG_ATH79_MACH_AW_NR580) += mach-aw-nr580.o
+ obj-$(CONFIG_ATH79_MACH_BHU_BXU2000N2_A)+= mach-bhu-bxu2000n2-a.o
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list