[OpenWrt-Devel] [PATCH] ar71xx: add TP-LINK TL-WDR3320 v2 support
Weijie Gao
hackpascal at gmail.com
Wed Sep 9 10:56:08 EDT 2015
Signed-off-by: Weijie Gao <hackpascal at gmail.com>
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
---
target/linux/ar71xx/base-files/etc/diag.sh | 1 +
.../ar71xx/base-files/etc/uci-defaults/01_leds | 4 +
.../ar71xx/base-files/etc/uci-defaults/02_network | 1 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 6 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-4.1 | 1 +
.../files/arch/mips/ath79/mach-tl-wdr3320-v2.c | 146 +++++++++++++++++++++
target/linux/ar71xx/generic/profiles/tp-link.mk | 11 ++
target/linux/ar71xx/image/Makefile | 46 ++++++-
.../816-MIPS-ath79-add-tl-wdr3320-v2-support.patch | 40 ++++++
10 files changed, 256 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wdr3320-v2.c
create mode 100644 target/linux/ar71xx/patches-4.1/816-MIPS-ath79-add-tl-wdr3320-v2-support.patch
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 36de775..0dcc844 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -256,6 +256,7 @@ get_status_led() {
tl-wa901nd | \
tl-wa901nd-v2 | \
tl-wa901nd-v3 | \
+ tl-wdr3320-v2 | \
tl-wdr3500 | \
tl-wr1041n-v2 | \
tl-wr1043nd | \
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
index e7f7a4c..4dafc1e 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
@@ -425,6 +425,10 @@ tl-wa901nd-v2)
ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
;;
+tl-wdr3320-v2)
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "tp-link:green:wlan5g" "phy0tpt"
+ ;;
+
tl-wdr3500)
ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "tp-link:green:wlan2g" "phy0tpt"
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
index 686fce9..37d5a63 100644
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
@@ -435,6 +435,7 @@ tew-712br |\
tl-mr3220 |\
tl-mr3220-v2 |\
tl-mr3420 |\
+tl-wdr3320-v2 |\
tl-wdr3500 |\
tl-wr741nd |\
tl-wr741nd-v4 |\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index e1f345e..c5440f9 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -221,6 +221,9 @@ tplink_board_detect() {
"342000"*)
model="TP-Link TL-MR3420"
;;
+ "332000"*)
+ model="TP-Link TL-WDR3320"
+ ;;
"350000"*)
model="TP-Link TL-WDR3500"
;;
@@ -763,6 +766,9 @@ ar71xx_board_detect() {
*"TL-WA901ND v3")
name="tl-wa901nd-v3"
;;
+ *"TL-WDR3320 v2")
+ name="tl-wdr3320-v2"
+ ;;
*"TL-WDR3500")
name="tl-wdr3500"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index c1962e4..1d56d99 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -338,6 +338,7 @@ platform_check_image() {
tl-wa901nd | \
tl-wa901nd-v2 | \
tl-wa901nd-v3 | \
+ tl-wdr3320-v2 | \
tl-wdr3500 | \
tl-wdr4300 | \
tl-wdr4900-v2 | \
diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1
index 21c4601..d0a6602 100644
--- a/target/linux/ar71xx/config-4.1
+++ b/target/linux/ar71xx/config-4.1
@@ -121,6 +121,7 @@ CONFIG_ATH79_MACH_TL_WA830RE_V2=y
CONFIG_ATH79_MACH_TL_WA901ND=y
CONFIG_ATH79_MACH_TL_WA901ND_V2=y
CONFIG_ATH79_MACH_TL_WAX50RE=y
+CONFIG_ATH79_MACH_TL_WDR3320_V2=y
CONFIG_ATH79_MACH_TL_WDR3500=y
CONFIG_ATH79_MACH_TL_WDR4300=y
CONFIG_ATH79_MACH_TL_WDR6500_V2=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wdr3320-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wdr3320-v2.c
new file mode 100644
index 0000000..3e452f2
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wdr3320-v2.c
@@ -0,0 +1,146 @@
+/*
+ * TP-LINK TL-WDR3320 v2 board support
+ *
+ * Copyright (C) 2012 Gabor Juhos <juhosg at openwrt.org>
+ * Copyright (C) 2015 Weijie Gao <hackpascal at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define WDR3320_GPIO_LED_WLAN5G 12
+#define WDR3320_GPIO_LED_SYSTEM 14
+#define WDR3320_GPIO_LED_QSS 15
+#define WDR3320_GPIO_LED_WAN 4
+#define WDR3320_GPIO_LED_LAN1 18
+#define WDR3320_GPIO_LED_LAN2 20
+#define WDR3320_GPIO_LED_LAN3 21
+#define WDR3320_GPIO_LED_LAN4 22
+
+#define WDR3320_GPIO_BTN_RESET 16
+
+#define WDR3320_KEYS_POLL_INTERVAL 20 /* msecs */
+#define WDR3320_KEYS_DEBOUNCE_INTERVAL (3 * WDR3320_KEYS_POLL_INTERVAL)
+
+#define WDR3320_WMAC_CALDATA_OFFSET 0x1000
+#define WDR3320_PCIE_CALDATA_OFFSET 0x5000
+
+static const char *wdr3320_part_probes[] = {
+ "tp-link",
+ NULL,
+};
+
+static struct flash_platform_data wdr3320_flash_data = {
+ .part_probes = wdr3320_part_probes,
+};
+
+static struct gpio_led wdr3320_leds_gpio[] __initdata = {
+ {
+ .name = "tp-link:green:qss",
+ .gpio = WDR3320_GPIO_LED_QSS,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:system",
+ .gpio = WDR3320_GPIO_LED_SYSTEM,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:wlan5g",
+ .gpio = WDR3320_GPIO_LED_WLAN5G,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button wdr3320_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = WDR3320_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = WDR3320_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static void __init wdr3320_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00);
+ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 tmpmac[ETH_ALEN];
+
+ ath79_register_m25p80(&wdr3320_flash_data);
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(wdr3320_leds_gpio),
+ wdr3320_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, WDR3320_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(wdr3320_gpio_keys),
+ wdr3320_gpio_keys);
+
+ ath79_init_mac(tmpmac, mac, 0);
+ ath79_register_wmac(art + WDR3320_WMAC_CALDATA_OFFSET, tmpmac);
+
+ ath79_init_mac(tmpmac, mac, -1);
+ ap9x_pci_setup_wmac_led_pin(0, 0);
+ ap91_pci_init(art + WDR3320_PCIE_CALDATA_OFFSET, tmpmac);
+
+ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_ONLY_MODE);
+
+ ath79_register_mdio(1, 0x0);
+
+ /* LAN */
+ ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
+
+ /* GMAC1 is connected to the internal switch */
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+
+ ath79_register_eth(1);
+
+ /* WAN */
+ ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
+
+ /* GMAC0 is connected to the PHY4 of the internal switch */
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_switch_data.phy_poll_mask = BIT(4);
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.phy_mask = BIT(4);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
+
+ ath79_register_eth(0);
+
+ ath79_register_usb();
+
+ ath79_gpio_output_select(WDR3320_GPIO_LED_LAN1,
+ AR934X_GPIO_OUT_LED_LINK0);
+ ath79_gpio_output_select(WDR3320_GPIO_LED_LAN2,
+ AR934X_GPIO_OUT_LED_LINK1);
+ ath79_gpio_output_select(WDR3320_GPIO_LED_LAN3,
+ AR934X_GPIO_OUT_LED_LINK2);
+ ath79_gpio_output_select(WDR3320_GPIO_LED_LAN4,
+ AR934X_GPIO_OUT_LED_LINK3);
+ ath79_gpio_output_select(WDR3320_GPIO_LED_WAN,
+ AR934X_GPIO_OUT_LED_LINK4);
+}
+
+MIPS_MACHINE(ATH79_MACH_TL_WDR3320_V2, "TL-WDR3320-v2",
+ "TP-LINK TL-WDR3320 v2",
+ wdr3320_setup);
diff --git a/target/linux/ar71xx/generic/profiles/tp-link.mk b/target/linux/ar71xx/generic/profiles/tp-link.mk
index 05d1019..2875290 100644
--- a/target/linux/ar71xx/generic/profiles/tp-link.mk
+++ b/target/linux/ar71xx/generic/profiles/tp-link.mk
@@ -266,6 +266,17 @@ endef
$(eval $(call Profile,TLWDR4300))
+define Profile/TLWDR3320V2
+ NAME:=TP-LINK TL-WDR3320v2
+ PACKAGES:=kmod-usb-core kmod-usb2 kmod-ledtrig-usbdev
+endef
+
+define Profile/TLWDR3320V2/Description
+ Package set optimized for the TP-LINK TL-WDR3320v2.
+endef
+$(eval $(call Profile,TLWDR3320V2))
+
+
define Profile/TLWDR4900V2
NAME:=TP-LINK TL-WDR4900v2
PACKAGES:=kmod-usb-core kmod-usb2 kmod-ledtrig-usbdev
diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile
index e6fe36a..1036399 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -53,6 +53,17 @@ define Build/mktplinkfw
$(if $(findstring sysupgrade,$1),-s) && mv $@.new $@ || rm -f $@
endef
+define Build/mktplinkfw-chn-v2
+ -$(STAGING_DIR_HOST)/bin/mktplinkfw \
+ -H $(TPLINK_HWID) -W $(TPLINK_HWREV) -F $(TPLINK_FLASHLAYOUT) -N OpenWrt -V $(REVISION) -m 2 \
+ -k $(word 1,$^) \
+ -r $@ \
+ -o $@.new \
+ -j -X 0x40000 \
+ -a $(call rootfs_align,$(FILESYSTEM)) \
+ $(if $(findstring sysupgrade,$1),-s) && mv $@.new $@ || rm -f $@
+endef
+
# -c combined image
define Build/mktplinkfw-initramfs
$(STAGING_DIR_HOST)/bin/mktplinkfw \
@@ -64,6 +75,16 @@ define Build/mktplinkfw-initramfs
@mv $@.new $@
endef
+define Build/mktplinkfw-initramfs-chn-v2
+ $(STAGING_DIR_HOST)/bin/mktplinkfw \
+ -H $(TPLINK_HWID) -W $(TPLINK_HWREV) -F $(TPLINK_FLASHLAYOUT) -N OpenWrt -V $(REVISION) -m 2 \
+ -k $@ \
+ -o $@.new \
+ -s -S \
+ -c
+ @mv $@.new $@
+endef
+
define Build/loader-common
rm -rf $@.src
$(MAKE) -C lzma-loader \
@@ -235,6 +256,15 @@ define Device/tplink
IMAGE/factory.bin := append-rootfs | mktplinkfw factory
endef
+define Device/tplink-chn-v2
+ TPLINK_HWREV := 0x1
+ KERNEL := kernel-bin | patch-cmdline | lzma
+ KERNEL_INITRAMFS := kernel-bin | patch-cmdline | lzma | mktplinkfw-initramfs-chn-v2
+ IMAGES := sysupgrade.bin factory.bin
+ IMAGE/sysupgrade.bin := append-rootfs | mktplinkfw-chn-v2 sysupgrade
+ IMAGE/factory.bin := append-rootfs | mktplinkfw-chn-v2 factory
+endef
+
define Device/tplink-nolzma
$(Device/tplink)
LOADER_FLASH_OFFS := 0x22000
@@ -274,6 +304,12 @@ $(Device/tplink)
IMAGE_SIZE := 15872k
endef
+define Device/tplink-chn-v2-4mlzma
+$(Device/tplink-chn-v2)
+ TPLINK_FLASHLAYOUT := 4Mlzma
+ IMAGE_SIZE := 3904k
+endef
+
define Device/tl-wdr4300-v1
$(Device/tplink-8mlzma)
BOARDNAME = TL-WDR4300
@@ -306,7 +342,15 @@ define Device/mw4530r-v1
$(Device/tl-wdr4300-v1)
TPLINK_HWID := 0x45300001
endef
-TARGET_DEVICES += tl-wdr3500-v1 tl-wdr3600-v1 tl-wdr4300-v1 tl-wdr4300-v1-il tl-wdr4310-v1 mw4530r-v1
+
+define Device/tl-wdr3320-v2
+$(Device/tplink-chn-v2-4mlzma)
+ BOARDNAME = TL-WDR3320-v2
+ DEVICE_PROFILE = TLWDR3320V2
+ TPLINK_HWID := 0x33200002
+endef
+
+TARGET_DEVICES += tl-wdr3500-v1 tl-wdr3600-v1 tl-wdr4300-v1 tl-wdr4300-v1-il tl-wdr4310-v1 mw4530r-v1 tl-wdr3320-v2
define Device/archer-c5
$(Device/tplink-16mlzma)
diff --git a/target/linux/ar71xx/patches-4.1/816-MIPS-ath79-add-tl-wdr3320-v2-support.patch b/target/linux/ar71xx/patches-4.1/816-MIPS-ath79-add-tl-wdr3320-v2-support.patch
new file mode 100644
index 0000000..8d6d686
--- /dev/null
+++ b/target/linux/ar71xx/patches-4.1/816-MIPS-ath79-add-tl-wdr3320-v2-support.patch
@@ -0,0 +1,40 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -1031,6 +1031,17 @@
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_WMAC
+
++config ATH79_MACH_TL_WDR3320_V2
++ bool "TP-LINK TL-WDR3320 v2 board support"
++ select SOC_AR934X
++ select ATH79_DEV_AP9X_PCI if PCI
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
++ select ATH79_DEV_USB
++ select ATH79_DEV_WMAC
++
+ config ATH79_MACH_TL_WDR3500
+ bool "TP-LINK TL-WDR3500 board support"
+ select SOC_AR934X
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -152,6 +152,7 @@
+ ATH79_MACH_TL_WA901ND, /* TP-LINK TL-WA901ND */
+ ATH79_MACH_TL_WA901ND_V2, /* TP-LINK TL-WA901ND v2 */
+ ATH79_MACH_TL_WA901ND_V3, /* TP-LINK TL-WA901ND v3 */
++ ATH79_MACH_TL_WDR3320_V2, /* TP-LINK TL-WDR3320 v2 */
+ ATH79_MACH_TL_WDR3500, /* TP-LINK TL-WDR3500 */
+ ATH79_MACH_TL_WDR4300, /* TP-LINK TL-WDR4300 */
+ ATH79_MACH_TL_WDR6500_V2, /* TP-LINK TL-WDR6500 v2 */
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -128,6 +128,7 @@
+ obj-$(CONFIG_ATH79_MACH_TL_WA830RE_V2) += mach-tl-wa830re-v2.o
+ obj-$(CONFIG_ATH79_MACH_TL_WA901ND) += mach-tl-wa901nd.o
+ obj-$(CONFIG_ATH79_MACH_TL_WA901ND_V2) += mach-tl-wa901nd-v2.o
++obj-$(CONFIG_ATH79_MACH_TL_WDR3320_V2) += mach-tl-wdr3320-v2.o
+ obj-$(CONFIG_ATH79_MACH_TL_WDR3500) += mach-tl-wdr3500.o
+ obj-$(CONFIG_ATH79_MACH_TL_WDR4300) += mach-tl-wdr4300.o
+ obj-$(CONFIG_ATH79_MACH_TL_WDR6500_V2) += mach-tl-wdr6500-v2.o
--
2.1.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list