[OpenWrt-Devel] ar71xx: add support for EnGenius ECB1750
Andrew Tyler
atyler at arocna3.com
Mon Nov 30 12:23:32 EST 2015
Okay. I just want to apologize for hammering this but I have been having
an issue trying to post the patch using my work email (office365). It
seemed to want to send it as an attachment with dos line endings tacked
on for some reason. I think ive got that taken care of now so here it
is: Signed-off-by: Andrew Tyler <atyler at arocna3.com>
diff --git a/package/base-files/files/bin/config_generate
b/package/base-files/files/bin/config_generate
index b6675f1..e1168d8 100755
--- a/package/base-files/files/bin/config_generate
+++ b/package/base-files/files/bin/config_generate
@@ -58,10 +58,7 @@ generate_network() {
lan)
uci -q batch <<-EOF
set network.$1.type='bridge'
- set network.$1.proto='static'
- set network.$1.ipaddr='192.168.1.1'
- set network.$1.netmask='255.255.255.0'
- set network.$1.ip6assign='60'
+ set network.$1.proto='dhcp'
EOF
;;
wan)
diff --git a/package/base-files/files/etc/config/network
b/package/base-files/files/etc/config/network
index d3cd3c6..37f6144 100644
--- a/package/base-files/files/etc/config/network
+++ b/package/base-files/files/etc/config/network
@@ -9,10 +9,7 @@ config interface loopback
config interface lan
option ifname eth0
option type bridge
- option proto static
- option ipaddr 192.168.1.1
- option netmask 255.255.255.0
- option ip6assign 60
+ option proto dhcp
config globals globals
option ula_prefix auto
diff --git a/package/base-files/files/etc/init.d/setwlanmac
b/package/base-files/files/etc/init.d/setwlanmac
new file mode 100755
index 0000000..8230595
--- /dev/null
+++ b/package/base-files/files/etc/init.d/setwlanmac
@@ -0,0 +1,16 @@
+#!/bin/sh /etc/rc.common
+# Copyright (C) 2014 OpenWrt.org
+
+START=98
+STOP=15
+
+start() {
+ grep athaddr /dev/mtdblock1 | cut -f2 -d= > /tmp/athaddr
+ grep ethaddr /dev/mtdblock1 | cut -f2 -d= > /tmp/ethaddr
+ ifconfig wlan1 down;
+ ifconfig wlan1 hw ether `grep ethaddr /dev/mtdblock1 | cut -f2
-d=`;
+ ifconfig wlan1 up;
+}
+stop() {
+ echo "Stop."
+}
diff --git
a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 74c3417..d81843c 100644
---
a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++
b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -75,6 +75,12 @@ case "$FIRMWARE" in
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat
/sys/class/net/eth0/address) +16)
;;
+ ecb1750)
+ ath10kcal_extract "art" 20480 2116
+ ifconfig eth0 hw ether `grep ethaddr /dev/mtdblock1 | cut -f2 -d=`
+ ath10kcal_patch_mac $(macaddr_add $(cat
/sys/class/net/eth0/address) +1)
+ ;;
+
esac
;;
"ath10k/cal-pci-0000:01:00.0.bin")
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh
b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index df77040..761afdf 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -491,6 +491,9 @@ ar71xx_board_detect() {
*"GL AR300")
name="gl-ar300"
;;
+ *"EnGenius ECB1750")
+ name="ecb1750"
+ ;;
*"EnGenius EPG5000")
name="epg5000"
;;
diff --git
a/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
b/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
index 92b3765..d8ede94 100644
--- a/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
+++ b/target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx
@@ -41,6 +41,8 @@ preinit_set_mac_address() {
wrt160nl)
fetch_mac_from_mtd nvram lan_hwaddr wan_hwaddr
;;
+ ecb1750)
+ fetch_mac_from_mtd u-boot-env ethaddr
esac
}
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 41886e3..d19a33c 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -216,6 +216,7 @@ platform_check_image() {
dlan-pro-1200-ac | \
dragino2 | \
epg5000 | \
+ ecb1750 | \
esr1750 | \
esr900 | \
ew-dorin | \
diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1
index eff197a..d0b0c8a 100644
--- a/target/linux/ar71xx/config-4.1
+++ b/target/linux/ar71xx/config-4.1
@@ -74,6 +74,7 @@ CONFIG_ATH79_MACH_EL_M150=y
CONFIG_ATH79_MACH_EL_MINI=y
CONFIG_ATH79_MACH_EPG5000=y
CONFIG_ATH79_MACH_ESR1750=y
+CONFIG_ATH79_MACH_ECB1750=y
CONFIG_ATH79_MACH_ESR900=y
CONFIG_ATH79_MACH_EW_DORIN=y
CONFIG_ATH79_MACH_F9K1115V2=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-ecb1750.c
b/target/linux/ar71xx/files/arch/mips/ath79/mach-ecb1750.c
new file mode 100644
index 0000000..aa3cf43
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-ecb1750.c
@@ -0,0 +1,109 @@
+/*
+ * EnGenius ECB1750 board support
+ *
+ * Andrew Tyler <atyler at arocna3.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as
published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ar8216_platform.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-gpio-buttons.h"
+#include "dev-eth.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define ECB1750_GPIO_LED_LAN 12
+#define ECB1750_GPIO_LED_WLAN_2G 13
+#define ECB1750_GPIO_LED_POWER 22
+#define ECB1750_GPIO_LED_WLAN_5G 23
+
+#define ECB1750_GPIO_BTN_RESET 17
+
+#define ECB1750_KEYS_POLL_INTERVAL 20 /* msecs */
+#define ECB1750_KEYS_DEBOUNCE_INTERVAL (3 * ECB1750_KEYS_POLL_INTERVAL)
+
+#define ECB1750_MAC0_OFFSET 0
+#define ECB1750_MAC1_OFFSET 1
+#define ECB1750_WMAC_CALDATA_OFFSET 0x1000
+#define ECB1750_PCIE_CALDATA_OFFSET 0x5000
+
+static struct gpio_led ecb1750_leds_gpio[] __initdata = {
+ {
+ .name = "ecb1750:amber:power",
+ .gpio = ECB1750_GPIO_LED_POWER,
+ .active_low = 0,
+ },
+ {
+ .name = "ecb1750:blue:lan",
+ .gpio = ECB1750_GPIO_LED_LAN,
+ .active_low = 0,
+ },
+ {
+ .name = "ecb1750:blue:wlan24",
+ .gpio = ECB1750_GPIO_LED_WLAN_2G,
+ .active_low = 0,
+ },
+ {
+ .name = "ecb1750:blue:wlan58",
+ .gpio = ECB1750_GPIO_LED_WLAN_5G,
+ .active_low = 0,
+ },
+};
+
+static struct gpio_keys_button ecb1750_gpio_keys[] __initdata = {
+ {
+ .desc = "Reset button",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = ECB1750_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = ECB1750_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static void __init ecb1750_setup(void)
+{
+ u8 *art = (u8 *)KSEG1ADDR(0x1fff0000);
+ u8 mac[6];
+
+ ath79_register_m25p80(NULL);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(ecb1750_leds_gpio),
+ ecb1750_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, ECB1750_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(ecb1750_gpio_keys),
+ ecb1750_gpio_keys);
+
+ ath79_init_mac(mac, art + ECB1750_MAC0_OFFSET, 1);
+ ath79_init_mac(ath79_eth0_data.mac_addr, art + ECB1750_MAC0_OFFSET, 0);
+ ath79_register_wmac(art + ECB1750_WMAC_CALDATA_OFFSET, NULL);
+ ath79_register_pci();
+
+ ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN);
+ ath79_register_mdio(0, 0x0);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, art + ECB1750_MAC0_OFFSET, 0);
+
+ /* GMAC0 is connected to the RMGII interface */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ath79_eth0_data.phy_mask = BIT(5);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth0_pll_data.pll_1000 = 0x9a000000;
+ ath79_eth0_pll_data.pll_100 = 0x80000101;
+ ath79_eth0_pll_data.pll_10 = 0x80001313;
+
+ath79_register_eth(0);
+}
+
+MIPS_MACHINE(ATH79_MACH_ECB1750, "ECB1750", "EnGenius ECB1750",
ecb1750_setup);
diff --git a/target/linux/ar71xx/generic/profiles/engenius.mk
b/target/linux/ar71xx/generic/profiles/engenius.mk
index 7ea93e3..2a19f58 100644
--- a/target/linux/ar71xx/generic/profiles/engenius.mk
+++ b/target/linux/ar71xx/generic/profiles/engenius.mk
@@ -16,6 +16,16 @@ endef
$(eval $(call Profile,EAP300V2))
+define Profile/ECB1750
+ NAME:=EnGenius ECB1750
+ PACKAGES:=kmod-ath9k kmod-ath10k
+endef
+
+define Profile/ECB1750/Description
+ Package set optimized for the EnGenius ECB1750.
+endef
+
+$(eval $(call Profile,ECB1750))
define Profile/ESR900
NAME:=EnGenius ESR900
diff --git a/target/linux/ar71xx/image/Makefile
b/target/linux/ar71xx/image/Makefile
index d12ad8b..5de7d82 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -1484,6 +1484,7 @@
cameo_ap94_mtdlayout=mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,6208k(firmware)
cameo_ap94_mtdlayout_fat=mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,7808k(firmware),64k(caldata)ro,64k at 0x660000(caldata_orig),6208k at 0x50000(firmware_orig)
esr900_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),13248k(rootfs),1024k(manufacture)ro,64k(backup)ro,320k(storage)ro,64k(caldata)ro,14656k at 0x40000(firmware)
esr1750_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),13248k(rootfs),1024k(manufacture)ro,64k(backup)ro,320k(storage)ro,64k(caldata)ro,14656k at 0x40000(firmware)
+ecb1750_mtdlayout=mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),1408k(kernel),14272k(rootfs),320k(userconfig),64k(art),15680k at 0x50000(firmware)
epg5000_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),13248k(rootfs),1024k(manufacture)ro,64k(backup)ro,320k(storage)ro,64k(caldata)ro,14656k at 0x40000(firmware)
ew-dorin_mtdlayout_4M=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),3712k(firmware),64k(art)
ew-dorin_mtdlayout_16M=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
@@ -2324,6 +2325,7 @@ $(eval $(call
SingleProfile,dLANLzma,64k,dLAN_pro_1200_ac,dlan-pro-1200-ac,dLAN-
$(eval $(call
SingleProfile,EnGenius,64k,ESR900,esr900,ESR900,ttyS0,115200,$$(esr900_mtdlayout),KRuImage,,0x4e))
$(eval $(call
SingleProfile,EnGenius,64k,ESR1750,esr1750,ESR1750,ttyS0,115200,$$(esr1750_mtdlayout),KRuImage,,0x61))
+$(eval $(call
SingleProfile,EnGenius,64k,ECB1750,ecb1750,ECB1750,ttyS0,115200,$$(ecb1750_mtdlayout),KRuImage,,0x61))
$(eval $(call
SingleProfile,EnGenius,64k,EPG5000,epg5000,EPG5000,ttyS0,115200,$$(epg5000_mtdlayout),KRuImage,,0x71))
$(eval $(call
SingleProfile,HiWiFi,64k,HIWIFI_HC6361,hiwifi-hc6361,HiWiFi-HC6361,ttyATH0,115200,$$(hiwifi_hc6361_mtdlayout),KRuImage))
diff --git
a/target/linux/ar71xx/patches-4.1/914-MIPS-ath79-add-ecb1750-support.patch
b/target/linux/ar71xx/patches-4.1/914-MIPS-ath79-add-ecb1750-support.patch
new file mode 100644
index 0000000..42bb18d
--- /dev/null
+++
b/target/linux/ar71xx/patches-4.1/914-MIPS-ath79-add-ecb1750-support.patch
@@ -0,0 +1,38 @@
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -70,6 +70,7 @@
+ ATH79_MACH_EAP7660D, /* Senao EAP7660D */
+ ATH79_MACH_EL_M150, /* EasyLink EL-M150 */
+ ATH79_MACH_EL_MINI, /* EasyLink EL-MINI */
++ ATH79_MACH_ECB1750, /* EnGenius ECB1750 */
+ ATH79_MACH_ESR1750, /* EnGenius ESR1750 */
+ ATH79_MACH_EPG5000, /* EnGenius EPG5000 */
+ ATH79_MACH_F9K1115V2, /* Belkin AC1750DB */
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -83,6 +83,7 @@
+ obj-$(CONFIG_ATH79_MACH_EL_MINI) += mach-el-mini.o
+ obj-$(CONFIG_ATH79_MACH_EPG5000) += mach-epg5000.o
+ obj-$(CONFIG_ATH79_MACH_ESR1750) += mach-esr1750.o
++obj-$(CONFIG_ATH79_MACH_ECB1750) += mach-ecb1750.o
+ obj-$(CONFIG_ATH79_MACH_F9K1115V2) += mach-f9k1115v2.o
+ obj-$(CONFIG_ATH79_MACH_GL_AR150) += mach-gl-ar150.o
+ obj-$(CONFIG_ATH79_MACH_GL_AR300) += mach-gl-ar300.o
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -289,6 +289,15 @@
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
++ select ATH79_DEV_WMAC
++
++config ATH79_MACH_ECB1750
++ bool "EnGenius ECB1750 board support"
++ select SOC_QCA955X
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
+ select ATH79_DEV_WMAC
+
+ config ATH79_MACH_WHR_HP_G300N
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list