[OpenWrt-Devel] [PATCH v2] [ramips] mt7621: add support for netis WF-2881
John Crispin
blogic at openwrt.org
Sat Nov 21 13:12:40 EST 2015
Hi,
the patch does not apply. is this against trunk or CC ?
John
On 14/11/2015 15:32, YounJaeRho wrote:
> netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
> It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
> The following patch adds support for this device.
>
> Tested and working:
> * ethernet
> * both WiFi radios
> * USB 3.0
> * buttons (reset button)
> * ethernet switch and USB diag LEDs
> * UART
> * GPIOs
>
>
> Signed-off-by: YounJae Rho <luxflow at live.com>
> ---
> Violation of alphabet ordering, indentation, naming, etc from previous version are resolved.
> Thanks Piotr Dymacz.
>
>
> target/linux/ramips/base-files/etc/board.d/01_leds | 3 +-
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/etc/diag.sh | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/WF-2881.dts | 123 +++++++++++++++++++++
> target/linux/ramips/image/Makefile | 6 +-
> target/linux/ramips/mt7621/config-3.18 | 4 +-
> target/linux/ramips/mt7621/profiles/netis.mk | 18 +++
> 9 files changed, 157 insertions(+), 3 deletions(-)
> create mode 100644 target/linux/ramips/dts/WF-2881.dts
> create mode 100644 target/linux/ramips/mt7621/profiles/netis.mk
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index c75a993..f9f8e3e 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -44,7 +44,8 @@ air3gii)
> all0239-3g|\
> hw550-3g|\
> mofi3500-3gn|\
> -sap-g3200u3)
> +sap-g3200u3|\
> +wf-2881)
> set_usb_led "$board:green:usb"
> ;;
> all0256n)
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index 0732796..d3f8121 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -78,6 +78,7 @@ ramips_setup_interfaces()
> oy-0001|\
> pbr-m1|\
> sap-g3200u3|\
> + wf-2881|\
> whr-300hp2|\
> whr-600d|\
> wsr-1166|\
> diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
> index 5376759..7d16f2c 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -150,6 +150,7 @@ get_status_led() {
> tew-692gr|\
> ur-326n4g|\
> ur-336un|\
> + wf-2881|\
> wr512-3gn)
> status_led="$board:green:wps"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 340bc4c..5ee494e 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -373,6 +373,9 @@ ramips_board_detect() {
> *"WCR-150GN")
> name="wcr-150gn"
> ;;
> + *"WF-2881")
> + name="wf-2881"
> + ;;
> *"WHR-1166D")
> name="whr-1166d"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index d3d9df3..687642f 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -107,6 +107,7 @@ platform_check_image() {
> w150m|\
> w306r-v20|\
> w502u|\
> + wf-2881|\
> whr-1166d|\
> whr-300hp2|\
> whr-600d|\
> diff --git a/target/linux/ramips/dts/WF-2881.dts b/target/linux/ramips/dts/WF-2881.dts
> new file mode 100644
> index 0000000..ba4a29b
> --- /dev/null
> +++ b/target/linux/ramips/dts/WF-2881.dts
> @@ -0,0 +1,123 @@
> +/dts-v1/;
> +
> +/include/ "mt7621.dtsi"
> +
> +/ {
> + compatible = "mediatek,mt7621-eval-board", "mediatek,mt7621-soc";
> + model = "NETIS WF-2881";
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x8000000>;
> + };
> +
> + palmbus at 1E000000 {
> + spi at b00 {
> + status="disabled";
> + };
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,57600";
> + };
> +
> + nand at 1e003000 {
> + compatible = "mtk,mt7621-nand";
> + bank-width = <2>;
> + reg = <0x1e003000 0x800
> + 0x1e003800 0x800>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x1000>;
> + read-only;
> + };
> +
> + partition at 80000 {
> + label = "config";
> + reg = <0x80000 0x20000>;
> + read-only;
> + };
> +
> + factory: partition at 100000 {
> + label = "factory";
> + reg = <0x100000 0x40000>;
> + read-only;
> + };
> +
> + partition at 140000 {
> + label = "firmware";
> + reg = <0x140000 0x6EC0000>;
> + };
> + };
> +
> + pcie at 1e140000 {
> + status = "okay";
> +
> + pcie0 {
> + mt76 at 0,0 {
> + reg = <0x0000 0 0 0 0>;
> + device_type = "pci";
> + mediatek,mtd-eeprom = <&factory 0x8000>;
> + mediatek,2ghz = <0>;
> + };
> + };
> +
> + pcie1 {
> + mt76 at 1,0 {
> + reg = <0x0000 0 0 0 0>;
> + device_type = "pci";
> + mediatek,mtd-eeprom = <&factory 0x0000>;
> + mediatek,5ghz = <0>;
> + };
> + };
> + };
> +
> + ethernet at 1e100000 {
> + mtd-mac-address = <&factory 0xe006>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + usb {
> + label = "wf-2881:green:usb";
> + gpios = <&gpio0 6 1>;
> + };
> +
> + wps {
> + label = "wf-2881:green:wps";
> + gpios = <&gpio0 0 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> +
> + reset {
> + label = "reset";
> + gpios = <&gpio0 12 1>;
> + linux,code = <0x198>;
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "uart3", "jtag";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
> index c66409d..060a2a4 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -950,7 +950,7 @@ endif
> #
>
> ifeq ($(SUBTARGET),mt7621)
> - TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3
> + TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 wf-2881
> endif
>
> define Device/mt7621
> @@ -1000,6 +1000,10 @@ define Device/sap-g3200u3
> DTS := SAP-G3200U3
> endef
>
> +define Device/wf-2881
> + DTS := WF-2881
> +endef
> +
> #
> # MT7628 Profiles
> #
> diff --git a/target/linux/ramips/mt7621/config-3.18 b/target/linux/ramips/mt7621/config-3.18
> index fb05d1e..bf1b3f9 100644
> --- a/target/linux/ramips/mt7621/config-3.18
> +++ b/target/linux/ramips/mt7621/config-3.18
> @@ -117,18 +117,20 @@ CONFIG_MIPS_MT_FPAFF=y
> CONFIG_MIPS_MT_SMP=y
> CONFIG_MIPS_PERF_SHARED_TC_COUNTERS=y
> # CONFIG_MIPS_VPE_LOADER is not set
> -# CONFIG_MTK_MTD_NAND is not set
> CONFIG_MODULES_USE_ELF_REL=y
> CONFIG_MT7621_WDT=y
> # CONFIG_MTD_CFI_INTELEXT is not set
> CONFIG_MTD_CMDLINE_PARTS=y
> CONFIG_MTD_M25P80=y
> +CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC=y
> CONFIG_MTD_PHYSMAP=y
> CONFIG_MTD_SPI_NOR=y
> CONFIG_MTD_SPLIT_FIRMWARE=y
> CONFIG_MTD_SPLIT_SEAMA_FW=y
> CONFIG_MTD_SPLIT_TRX_FW=y
> CONFIG_MTD_SPLIT_UIMAGE_FW=y
> +CONFIG_MTK_MTD_NAND=y
> CONFIG_NEED_DMA_MAP_STATE=y
> CONFIG_NET_FLOW_LIMIT=y
> CONFIG_NET_RALINK=y
> diff --git a/target/linux/ramips/mt7621/profiles/netis.mk b/target/linux/ramips/mt7621/profiles/netis.mk
> new file mode 100644
> index 0000000..6de40af
> --- /dev/null
> +++ b/target/linux/ramips/mt7621/profiles/netis.mk
> @@ -0,0 +1,18 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/WF-2881
> + NAME:=NETIS WF-2881
> + PACKAGES:=\
> + kmod-usb-core kmod-usb3 kmod-usb-hid \
> + kmod-ledtrig-usbdev
> +endef
> +
> +define Profile/WF-2881/Description
> + Package set compatible with the NETIS WF-2881 board.
> +endef
> +$(eval $(call Profile,WF-2881))
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list