[OpenWrt-Devel] [PATCH] ramips:Add support for ZTE Q7
郭传鈜
gch981213 at gmail.com
Tue Mar 31 07:49:17 EDT 2015
Sorry I resend this patch just because of the title...
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213 at gmail.com>
---
target/linux/ramips/base-files/etc/board.d/01_leds | 3 +
.../linux/ramips/base-files/etc/board.d/02_network | 1 +
target/linux/ramips/base-files/etc/diag.sh | 3 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/ZTE-Q7.dts | 111 +++++++++++++++++++++
target/linux/ramips/image/Makefile | 2 +
7 files changed, 124 insertions(+)
create mode 100644 target/linux/ramips/dts/ZTE-Q7.dts
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index bfe1c0c..56ba3b7 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -237,6 +237,9 @@ case $board in
set_usb_led "lenovo:blue:usb"
set_wifi_led "lenovo:blue:wifi"
;;
+ zte-q7)
+ set_wifi_led "zte:blue:status"
+ ;;
esac
board_config_flush
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 89d1681..d4ec19d 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -46,6 +46,7 @@ ramips_setup_interfaces()
3g150b | \
3g300m | \
w150m | \
+ zte-q7 | \
all0256n | \
all5002 | \
all5003 | \
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 50b6ff2..5301593 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -224,6 +224,9 @@ get_status_led() {
y1s)
status_led="lenovo:blue:power"
;;
+ zte-q7)
+ status_led="zte:red:status"
+ ;;
esac
}
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 4527414..fc6eb37 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -379,6 +379,9 @@ ramips_board_detect() {
*"ZBT WR8305RT")
name="wr8305rt"
;;
+ *"ZTE Q7")
+ name="zte-q7"
+ ;;
*"Lenovo Y1")
name="y1"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index fffbe72..a5773b5 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -114,6 +114,7 @@ platform_check_image() {
xiaomi-miwifi-mini |\
y1 |\
y1s |\
+ zte-q7 |\
zbt-wa05)
[ "$magic" != "27051956" ] && {
echo "Invalid image type."
diff --git a/target/linux/ramips/dts/ZTE-Q7.dts b/target/linux/ramips/dts/ZTE-Q7.dts
new file mode 100644
index 0000000..9efc35e
--- /dev/null
+++ b/target/linux/ramips/dts/ZTE-Q7.dts
@@ -0,0 +1,111 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+ compatible = "ZTE-Q7", "ralink,mt7620a-soc";
+ model = "ZTE Q7";
+
+ palmbus at 10000000 {
+
+ gpio0: gpio at 600 {
+ status = "okay";
+ };
+
+ gpio1: gpio at 638 {
+ status = "okay";
+ };
+
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "en25q64";
+ reg = <0 0>;
+ linux,modalias = "m25p80", "en25q64";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0x7b0000>;
+ };
+ };
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "ephy", "wled", "nd_sd";
+ ralink,function = "gpio";
+ };
+ };
+ };
+
+ ethernet at 10100000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ephy_pins>;
+ mtd-mac-address = <&factory 0x4>;
+ ralink,port-map = "wllll";
+ };
+
+ wmac at 10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ sdhci at 10130000 {
+ status = "okay";
+ };
+
+ ehci at 101c0000 {
+ status = "okay";
+ };
+
+ ohci at 101c1000 {
+ status = "okay";
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ statred {
+ label = "zte:red:status";
+ gpios = <&gpio0 13 1>;
+ };
+ statblue {
+ label = "zte:blue:status";
+ gpios = <&gpio0 9 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+ reset {
+ label = "reset";
+ gpios = <&gpio1 2 1>;
+ linux,code = <0x198>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 45ae3a5..bc1fe181 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -862,6 +862,7 @@ Image/Build/Profile/WR8305RT=$(call BuildFirmware/Default8M/$(1),$(1),wr8305rt,W
Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
Image/Build/Profile/XIAOMI-MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),xiaomi-miwifi-mini,XIAOMI-MIWIFI-MINI)
+Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
Image/Build/Profile/ArcherC20i=$(call BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
@@ -891,6 +892,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/WRTNODE,$(1))
$(call Image/Build/Profile/WT3020,$(1))
$(call Image/Build/Profile/XIAOMI-MIWIFI-MINI,$(1))
+ $(call Image/Build/Profile/ZTE-Q7,$(1))
$(call Image/Build/Profile/ZBT-WA05,$(1))
$(call Image/Build/Profile/ArcherC20i,$(1))
endef
--
2.1.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list