[OpenWrt-Devel] [PATCH 1/3] initial support for TP-Link Archer C2600

Josh Bendavid joshbendavid at gmail.com
Thu Dec 17 11:45:31 EST 2015


(Sorry, missed the changes to tplink-safeloader in firmware tools
here, have submitted a separate patch with just those)

On 17 December 2015 at 13:34, Josh Bendavid <joshbendavid at gmail.com> wrote:
> Add initial support for Archer C2600 to Makefiles and profiles along with needed modifications to tplink-safeloader in firmware-tools.  This is sufficient to build a working factory image flashable both from stock web ui and bootloader tftp recovery.  Sysupgrade is working as well.
>
> Working: Wired network, wireless (both bands), power/status/lan/wan/usb led's
>
> Not working: wireless status led's (these are not controlled through gpio, but rather through the QCA9980 pcie chips).  Also there is no way to set the wan led to orange, which is possible in the stock firmware.  Kernel 4.1 build does not boot currently.
>
> Not tested: Hardware buttons.
>
> Signed-off-by: Josh Bendavid <joshbendavid at gmail.com>
>
> ---
>  include/image.mk                                   | 11 ++++
>  .../linux/ipq806x/base-files/etc/board.d/01_leds   |  7 +++
>  .../ipq806x/base-files/etc/board.d/02_network      |  3 +-
>  .../etc/hotplug.d/firmware/11-ath10k-caldata       | 66 ++++++++++++++++++++++
>  target/linux/ipq806x/base-files/lib/ipq806x.sh     |  3 +
>  .../ipq806x/base-files/lib/upgrade/platform.sh     | 34 ++++++++++-
>  target/linux/ipq806x/image/Makefile                | 24 +++++++-
>  target/linux/ipq806x/profiles/tplink.mk            | 20 +++++++
>  8 files changed, 165 insertions(+), 3 deletions(-)
>  create mode 100644 target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
>  create mode 100644 target/linux/ipq806x/profiles/tplink.mk
>
> diff --git a/include/image.mk b/include/image.mk
> index 6b2fb1a..70b7f4f 100644
> --- a/include/image.mk
> +++ b/include/image.mk
> @@ -327,6 +327,17 @@ define Build/netgear-dni
>         mv $@.new $@
>  endef
>
> +define Build/tplink-safe
> +       $(STAGING_DIR_HOST)/bin/tplink-safeloader \
> +               -B $(TPLINK_BOARD_ID) -V OpenWrt.$(REVISION) \
> +               -k $(word 1,$^) \
> +               -r $(word 2,$^) \
> +               -j \
> +               $(if $(findstring sysupgrade,$1),-S) \
> +               -o $@.new
> +       mv $@.new $@
> +endef
> +
>  define Build/fit
>         $(TOPDIR)/scripts/mkits.sh \
>                 -D $(DEVICE_NAME) -o $@.its -k $@ \
> diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
> index 07b5b06..46070ad6 100755
> --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
> +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
> @@ -19,6 +19,13 @@ r7500)
>         ucidef_set_led_default "wps" "WPS" "r7500:white:wps" "0"
>         ucidef_set_led_default "rfkill" "rfkill" "r7500:white:rfkill" "0"
>         ;;
> +c2600)
> +       ucidef_set_led_usbdev "usb1" "USB 1" "usb_2:blue" "2-1"
> +       ucidef_set_led_usbdev "usb2" "USB 2" "usb_4:blue" "4-1"
> +       ucidef_set_led_netdev "wan" "WAN" "wan:blue" "eth0"
> +       ucidef_set_led_netdev "lan" "LAN" "lan:blue" "br-lan"
> +       ucidef_set_led_default "general" "general" "ledgnr:blue" "1"
> +       ;;
>  *)
>         ;;
>  esac
> diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
> index 1302a55..9f061e4 100755
> --- a/target/linux/ipq806x/base-files/etc/board.d/02_network
> +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
> @@ -13,7 +13,8 @@ board=$(ipq806x_board_name)
>
>  case "$board" in
>  ap148 |\
> -r7500)
> +r7500 |\
> +c2600)
>         ucidef_add_switch "switch0" \
>                 "1:lan" "2:lan" "3:lan" "4:lan" "6 at eth1" "5:wan" "0 at eth0"
>         ;;
> diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> new file mode 100644
> index 0000000..7a423de
> --- /dev/null
> +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> @@ -0,0 +1,66 @@
> +#!/bin/sh
> +
> +ath10kcal_die() {
> +       echo "ath10cal: " "$*"
> +       exit 1
> +}
> +
> +ath10kcal_from_file() {
> +       local source=$1
> +       local offset=$2
> +       local count=$3
> +
> +       dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
> +               ath10kcal_die "failed to extract calibration data from $source"
> +}
> +
> +ath10kcal_extract() {
> +       local part=$1
> +       local offset=$2
> +       local count=$3
> +       local mtd
> +
> +       mtd=$(find_mtd_chardev $part)
> +       [ -n "$mtd" ] || \
> +               ath10kcal_die "no mtd device found for partition $part"
> +
> +       dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
> +               ath10kcal_die "failed to extract calibration data from $mtd"
> +}
> +
> +ath10kcal_patch_mac() {
> +       local mac=$1
> +
> +       [ -z "$mac" ] && return
> +
> +       macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
> +}
> +
> +[ -e /lib/firmware/$FIRMWARE ] && exit 0
> +
> +. /lib/ipq806x.sh
> +. /lib/functions.sh
> +. /lib/functions/system.sh
> +
> +board=$(ipq806x_board_name)
> +
> +
> +case "$FIRMWARE" in
> +"ath10k/cal-pci-0000:01:00.0.bin")
> +       case $board in
> +       c2600)
> +               ath10kcal_extract "0:ART" 4096 12064
> +               ;;
> +       esac
> +       ;;
> +"ath10k/cal-pci-0001:01:00.0.bin")
> +       case $board in
> +       c2600)
> +               ath10kcal_extract "0:ART" 20480 12064
> +               ;;
> +       esac
> +       ;;
> +*)
> +       exit 1
> +       ;;
> +esac
> diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
> index 5b27bde..262183f 100644
> --- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
> +++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
> @@ -23,6 +23,9 @@ ipq806x_board_detect() {
>         *"R7500")
>                 name="r7500"
>                 ;;
> +       *"C2600")
> +               name="c2600"
> +               ;;
>         esac
>
>         [ -z "$name" ] && name="unknown"
> diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> index c0e19a1..7fc08bb 100644
> --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
> @@ -11,6 +11,14 @@ platform_check_image() {
>                 nand_do_platform_check $board $1
>                 return $?;
>                 ;;
> +       c2600)
> +               local magic_long="$(get_magic_long "$1")"
> +               [ "$magic_long" != "27051956" ] && {
> +                       echo "Invalid image, bad magic: $magic_long"
> +                       return 1
> +               }
> +               return 0;
> +               ;;
>         *)
>                 return 1;
>         esac
> @@ -27,4 +35,28 @@ platform_pre_upgrade() {
>         esac
>  }
>
> -# use default for platform_do_upgrade()
> +platform_do_upgrade() {
> +       local board=$(ipq806x_board_name)
> +
> +       case "$board" in
> +       c2600)
> +               platform_do_upgrade_c2600 "$ARGV"
> +               ;;
> +       esac
> +}
> +
> +platform_do_upgrade_c2600() {
> +       local kernpart="0:HLOS"
> +       local rootfspart="rootfs"
> +
> +       local kernel_mtd="$(find_mtd_index $kernpart)"
> +
> +       local kerndev="/dev/mtd${kernel_mtd}"
> +       local rootfsdev=$rootfspart
> +
> +       PART_NAME="${kerndev}:${rootfsdev}"
> +       MTD_CONFIG_ARGS="-s 0x200000"
> +
> +       default_do_upgrade "$ARGV"
> +
> +}
> diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
> index 14cf442..956d724 100644
> --- a/target/linux/ipq806x/image/Makefile
> +++ b/target/linux/ipq806x/image/Makefile
> @@ -85,6 +85,19 @@ define Device/DniImage
>  endef
>  DEVICE_VARS += KERNEL_SIZE NETGEAR_BOARD_ID NETGEAR_HW_ID DEVICE_BLOCK_SIZE DEVICE_PAGE_SIZE
>
> +define Device/TpSafeImage
> +       PROFILES += $$(DEVICE_NAME)
> +       FILESYSTEMS := squashfs
> +       KERNEL_SUFFIX := -uImage
> +       KERNEL = kernel-bin | append-dtb | uImage none
> +       KERNEL_NAME := zImage
> +       TPLINK_BOARD_ID :=
> +       IMAGES := factory.bin sysupgrade.bin
> +       IMAGE/factory.bin := tplink-safe factory
> +       IMAGE/sysupgrade.bin := tplink-safe sysupgrade
> +endef
> +DEVICE_VARS += TPLINK_BOARD_ID
> +
>  define Device/AP148
>         $(call Device/FitImage)
>         $(call Device/UbiFit)
> @@ -103,6 +116,15 @@ define Device/AP148-legacy
>         BOARD_NAME := ap148
>  endef
>
> +define Device/C2600
> +       $(call Device/TpSafeImage)
> +       DEVICE_DTS := qcom-ipq8064-c2600
> +       BLOCKSIZE := 128KiB
> +       PAGESIZE := 2048
> +       BOARD_NAME := c2600
> +       TPLINK_BOARD_ID := C2600
> +endef
> +
>  define Device/DB149
>         $(call Device/FitImage)
>         DEVICE_DTS := qcom-ipq8064-db149
> @@ -121,6 +143,6 @@ define Device/R7500
>         BOARD_NAME := r7500
>  endef
>
> -TARGET_DEVICES += AP148 AP148-legacy DB149 R7500
> +TARGET_DEVICES += AP148 AP148-legacy C2600 DB149 R7500
>
>  $(eval $(call BuildImage))
> diff --git a/target/linux/ipq806x/profiles/tplink.mk b/target/linux/ipq806x/profiles/tplink.mk
> new file mode 100644
> index 0000000..d3f5a6c
> --- /dev/null
> +++ b/target/linux/ipq806x/profiles/tplink.mk
> @@ -0,0 +1,20 @@
> +#
> +# Copyright (c) 2014 The Linux Foundation. All rights reserved.
> +# Copyright (C) 2009 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/C2600
> +       NAME:=TP-Link Archer C2600
> +       PACKAGES:= \
> +               kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \
> +               kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \
> +               kmod-ath10k ath10k-firmware-qca99x0 wpad-mini
> +endef
> +
> +define Profile/C2600/Description
> +       Package set for the TP-Link Archer C2600.
> +endef
> +$(eval $(call Profile,C2600))
> --
> 2.6.4
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list